Parts for Ge GTE21GSHCSS: Doors Parts

A replacement reversible plug door that restores a clean, finished opening and secures the power inlet. Designed to match OEM fit and function for easy field replacement and a neat appearance. What it does:

• Covers and protects the appliance power plug opening from dust and debris
• Reversible design lets you install the hinge on either side to match cabinet/panel orientation
• Helps keep the plug area secure and prevents accidental contact with wiring
• Useful when replacing a damaged or missing plug door to restore original appearance

• One plug door

• Basic snap-in or screw-mount installation; inspect attachment points for damage before installing
• Turn off and disconnect power to the appliance before accessing the plug area
• Use common hand tools; do not force the part into place—if fit is tight, verify orientation and mounting hardware
• If mounting clips or screws are damaged or missing, replace them to ensure a secure fit

This door gasket forms an airtight seal around the freezer door, keeping cold air in and warm, humid air out. Replace a torn, warped, or compressed gasket to restore proper sealing, reduce frost, and maintain consistent freezer temperatures.

• Seals the freezer door to the cabinet to contain cold air and block warm, moist air
• Helps reduce frost/ice buildup and temperature swings
• Can address issues like visible gaps, tears, hardening/warping, condensation around the door, or the door popping open
• A worn gasket may cause longer run times and difficulty maintaining set temperatures

• Disconnect power before starting
• Remove the old gasket; depending on the model, it presses into a channel or is held by retainer screws
• Warm the new gasket (warm water or low heat) to relax folds, then seat it evenly all the way around
• Close the door and check for uniform contact; adjust seating/retainers to eliminate gaps

This stainless steel freezer door panel replaces a damaged or worn outer door surface to restore appearance and protect the freezer compartment. It's a direct-fit exterior panel that keeps the freezer looking like new. What it does

• Replaces a dented, scratched or corroded outer freezer door surface
• Restores the cabinet's finished appearance and uniform stainless look
• Provides the proper mounting surface for door hardware and trim
• Helps the door close and seal properly by returning correct panel alignment

• Disconnect power to the appliance before starting any work
• Support the door when removing or installing the panel; it may require two people
• Use appropriate hand tools and follow manufacturer fastening order to avoid damaging the finish
• Check door alignment and gasket seating after installation; replace fasteners or trim as needed

This door handle fastener secures the refrigerator's handle to its mounting points, keeping it tight and aligned. Replace a stripped or missing fastener to restore a solid, safe grip when opening and closing the door.

• Secures the handle to the door's mounting studs or brackets
• Helps prevent handle wobble, sagging, and misalignment
• Replaces broken, stripped, or missing hardware
• Common symptoms: loose or wobbly handle, handle pulls off, or handle won't stay tight

• Disconnect power to the refrigerator before servicing
• Protect the door finish and support the handle during removal
• Remove the handle per your model's instructions, replace the fastener at the mounting point, and reattach the handle
• Tighten hardware until snug; do not overtighten

This refrigerator door gasket in Dorian Gray creates a tight seal between the door and cabinet to keep cold air in and humidity out. Replace a warped, torn, or leaky gasket to restore proper cooling performance and reduce frost and moisture problems.

• Seals the door perimeter to maintain temperature and energy efficiency
• Helps prevent condensation, frost buildup, and warm spots near the door
• Replaces gaskets that are cracked, deformed, or no longer sealing
• Common symptoms: visible gaps, door won't close smoothly, moisture/ice around the door, longer run times

• Disconnect power and clear the door area before starting
• Warm the new gasket with hot water or low heat to improve flexibility; do not overheat
• Press the retainer lip fully into the door channel, working evenly around corners
• Close the door and check for uniform contact; adjust hinges/strike as needed and allow the gasket to set

This stainless-steel refrigerator door replaces a damaged or dented outer door and restores proper appearance and function. It provides the finished exterior surface and mounting points for hinges, handles, and trim. What it does

• Replaces a dented, scratched or corroded outer refrigerator door to restore the appliance's appearance
• Provides the correct mounting surface for door hinges, handle hardware and exterior trim
• Helps the door close and align properly when installed, reducing gaps that can affect cooling
• Intended for exterior cosmetic/structural replacement—not an internal liner or insulation assembly

• Disconnect power to the refrigerator and remove refrigerated contents before starting work
• Door is heavy and awkward; use two people to remove and install to avoid damage or injury
• Transfer existing hinges, handle and trim as required
• Check hinge alignment and door gap during installation; slight adjustments may be needed for proper closing

This fixed freezer shelf provides a stable storage surface designed to replace a worn or broken freezer shelf, restoring organization and safe stacking for frozen foods. Fits into existing shelf supports for a straightforward swap. What it does:

• Replaces a damaged or missing fixed freezer shelf to restore storage capacity and organization
• Provides a stable surface to prevent items from falling or blocking vents
• Helps keep frozen items separated for easier access and inventory
• Works with existing shelf supports and slides into place when aligned correctly

• Remove food and packaging from the area before replacing the shelf
• Power disconnect is recommended as a general safety precaution before servicing appliances
• Align shelf with existing supports and carefully lower into place until fully seated
• If the shelf is glass, handle with care and wear gloves to reduce breakage risk

Restore a sturdy, level storage surface in your refrigerator's main compartment with this fresh food fixed shelf. Replace a cracked, broken, or missing shelf to regain intended capacity and keep items organized in the fresh food section.

• Provides a solid, level surface in the fresh food compartment
• Replaces a cracked, shattered, or missing shelf
• Addresses issues like broken frame tabs or a shelf that won't sit level
• Helps prevent items from tipping and restores proper spacing

• Disconnect power and remove food from the area before replacing the shelf
• Slide out the damaged shelf and carefully position the new shelf into the mounting slots
• Ensure the shelf is fully seated on its supports before loading items
• Handle carefully; use two hands and avoid sudden temperature changes

The Fresh Food Fixed Shelf is an OEM part for GE refrigerators. This door shelf is designed to fit within the fresh food section of your GE refrigerator, providing additional storage space for various food items. It offers a convenient place to store bottles, jars, and other items, keeping them easily accessible and organized.

A bad door shelf can occur due to wear and tear, accidental damage, or other factors. If you notice symptoms such as cracks, warping, or the shelf not attaching securely to the refrigerator door, it may be time to replace the door shelf.

Symptoms of a bad door shelf include:

• Cracks or damage
• Warping
• Shelf not attaching securely to the refrigerator door

Restore organization in your GE refrigerator by replacing the faulty door shelf with this genuine OEM part.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

The Handle Assembly is an OEM component specifically designed for GE side-by-side refrigerators. It consists of both the refrigerator and freezer door handles connected by a single mounting bracket. 

This assembly provides ergonomic grip points and a synchronized operation to smoothly open both doors at once or individually. Its precisely designed bracket ensures stable, lasting performance year after year.

Symptoms of a bad handle assembly include:

• Loose, shaky, or unstable door handles  
• Detachment of one or both handles from the fridge
• Difficulty opening both doors together
• Disconnected or misaligned handles  

Color: Stainless steel

Causes can be normal wear over extended use, unbalanced opening force, or accidental impacts damaging internal assembly parts.

Replace with this genuine OEM GE handle assembly to restore easy access and dependable dual-door functionality. Compatible also with Hotpoint, RCA, and select Kenmore models for a factory-fit replacement.
 

Badge assembly that restores the exterior nameplate on compatible refrigerators, returning factory appearance and clear appliance identification. Ideal for replacing faded, cracked or missing emblems for a like-new finish. What it does:

• Restores the appliance's exterior identification and cosmetic finish where the original emblem is faded, cracked, or missing.
• Covers the mounting area and provides the finished look customers expect from the door surface.
• Matches factory styling so the appliance maintains a consistent, OEM appearance.
• Useful whenever visible badge damage detracts from the refrigerator's appearance.

• High-level surface-mount part—inspect the door surface and remove any old adhesive or residue before installing.
• Alignment is important; position carefully and press firmly to engage any snap-in tabs or adhesive backing.
• No electrical disconnection is typically required for exterior cosmetic badges, but avoid prying behind panels that expose wiring or components.

Replacement dairy bin assembly for refrigerator door. Restores enclosed door storage to keep butter, cheese and other small items organized and contained, preventing spills and making everyday access easier. What it does:

• Replaces a cracked, broken or worn door dairy bin to restore proper storage and containment for small food items.
• Mounts to the refrigerator door shelf to secure butter, cheese and other small items so they don't fall or shift during use.
• Helps eliminate common symptoms like loose or missing door storage, items falling from the door shelf, or a chipped/ruined dairy bin.

• Remove food and any adjustable door shelves before replacing the bin to avoid spills or damage.
• Align the bin with the door shelf rails and seat it until fully engaged; some models snap or slide into place.
• Inspect door shelf rails and catches for damage and clean mounting surfaces before installing.