Parts for Ge GTE22JTNBRBB: Doors Parts

This plastic BB handle replaces a worn or damaged refrigerator/freezer drawer or door handle so you can open and close it with a secure grip. Designed as a direct-fit exterior handle replacement for a clean, finished look. What it does:

• Replaces cracked, broken, or loose BB-style exterior handles
• Restores a secure grip for opening doors or drawers
• Keeps the appliance appearance consistent and functional
• Helps prevent further damage caused by using a damaged handle

• Disconnect power to the appliance before servicing to avoid electrical or injury risk
• Handle typically secures with mounting screws or retention clips; use appropriate screwdriver and keep hardware
• Align handle carefully to avoid scratching the appliance finish

This freezer door gasket forms an airtight seal between the door and cabinet to keep cold air in and moisture out. Replace it when the original is torn, warped, or leaking to restore proper temperature and defrost performance.

• Creates a continuous seal around the freezer door to prevent air leaks
• Helps maintain set temperatures and reduces frost/condensation buildup
• Replaces a gasket that is cracked, torn, deformed, or no longer sealing
• Common symptoms: frost or moisture along the door edge, door not closing fully, warm spots near the gasket

• Disconnect power before servicing
• Let the new gasket warm up (room temperature or brief warm-water soak) to increase flexibility
• Seat the gasket fully in the retainer/channel; use low heat (hair dryer) to relax waves—do not overheat
• Check the seal with a paper/dollar-bill test around the perimeter and adjust alignment if needed

This freezer door stop cushions and limits the door's travel to protect the hinge and cabinet edge, helping the door close smoothly and preventing over-travel damage. Fits black trim locations on compatible freezers. What it does:

• Acts as a bumper to stop the freezer door from swinging too far
• Cushions impact, reducing stress on hinge components and cabinet
• Helps the door align and close flush to maintain seal performance
• Common symptom fix: door hits cabinet, scrapes, or sits unevenly

• Remove any food/obstructions and support the door before replacing the stop
• Usually a simple snap-in or screw-on replacement; small hand tools may be required
• Inspect surrounding hinge and trim for damage when replacing
• Follow all safety precautions; unplug unit or disconnect power before performing extended service

This replacement gasket seals the refrigerator's fresh food compartment in Dorian Gray. It closes gaps around the door to keep cold air in and humid air out, helping stabilize temperatures and reduce condensation for reliable cooling.

• Seals the perimeter of the fresh food door to prevent warm air leaks
• Helps maintain proper temperature and humidity in the refrigerator section
• Reduces condensation or "sweating" around the door area
• Common signs it's worn: tears, cracks, warping/shrinkage, visible gaps, or the door not sealing fully

• Unplug the refrigerator and unload the door bins
• Pull the old gasket from the retainer; on some models, slightly loosen (do not remove) liner screws to release the seal
• Warm the new gasket in hot water or with low, safe heat to relax it; seat corners first, then press the gasket fully into the retainer
• Close the door to check for even contact all around; adjust as needed and allow up to 24 hours for the gasket to conform

This refrigerator door shelf mounts on the inner door to hold condiments, jars, and bottles. Replacing a cracked or missing shelf restores secure, easy-access storage and helps keep items upright when you open and close the door.

• Snaps into the door's molded rails or end tabs to organize and retain containers
• Restores lost door storage capacity for condiments, jars, and tall bottles
• Common symptoms: cracked or broken plastic, loose or missing shelf, items falling from the door
• Visible damage or worn locking tabs prevent the shelf from staying seated

• Remove the old shelf by lifting up and out; empty contents before removal
• Align the new shelf with the door rails/end tabs and press down until fully seated—do not force
• No tools typically required; handle plastic carefully to avoid cracking
• Install in the same location as the original for proper fit and door clearance

A replacement reversible plug door that covers and protects the appliance power inlet while letting the cord exit left or right for tidy cord routing. Restores a clean back panel appearance and helps keep the power connection protected from debris. What it does:

• Covers the power inlet opening to protect the plug and inlet from dust and debris.
• Reversible design lets you route the power cord to either side to fit against the wall.
• Helps keep the cord tucked close to the appliance so the unit can sit flush with cabinetry or walls.
• Replace when the door is cracked, broken, missing, or no longer holds the plug securely.

• Always unplug the appliance before starting any repair or inspection.
• May require access to the rear panel; check your owner's manual for disassembly steps.
• Check orientation before finalizing installation to ensure correct left/right cord routing.

This kit replaces the mounting hardware that secures a refrigerator/freezer door handle to the door, restoring a solid, safe grip and clean appearance when the original fasteners are missing, damaged, or stripped.

• Provides the correct hardware to attach and secure the door handle
• Helps resolve loose, wobbly, or detached handles
• Replaces missing, damaged, or stripped handle fasteners
• Supports proper handle alignment and feel

• Disconnect power (and water, if applicable) and wear gloves.
• Support the handle while removing old hardware to prevent drops or scratches.
• Start threads by hand to avoid cross-threading; tighten evenly and do not overtighten.
• The handle is secure and the door opens/closes normally.

This black emblem badge restores the appliance's front appearance by replacing a faded, scratched, or missing logo accent. It provides a clean, finished look so the appliance matches its original styling. What it does:

• Replaces a worn or missing badge to restore factory appearance
• Hides cosmetic damage on the control bezel or exterior trim
• Helps maintain resale value and consistent styling across the appliance lineup
• Visible cosmetic part only — does not affect appliance function

• One black emblem badge

• Clean and dry the mounting area before installing to ensure proper fit
• Align carefully before seating; some badges press into place or adhere to the surface
• Use caution around sharp edges and disconnect power when working near electrical components

This plug button thimble is a small control-panel insert that secures and centers push buttons, helping keep button caps in place and reducing moisture or debris entry. It restores proper button feel and alignment on the control panel. What it does:

• Centers and retains push-button caps so buttons press and release correctly
• Helps prevent dirt and spills from entering the control-panel opening
• Replaces a cracked, worn, or missing thimble that lets buttons wobble or fall inward
• Compatible with the original push-button assembly to restore original fit and function

• Simple, non-electrical replacement—power to the appliance is not required for this exterior part, but unplugging is recommended if removing trim near live components
• Remove the button cap first, press the old thimble out from the front or back as applicable, then press the new thimble into the panel opening until fully seated
• Inspect button cap and surrounding trim for damage; replace any damaged mating parts for best fit
• Use care to avoid scratching the control panel; keep small parts away from children

The Screw is an OEM replacement part for GE brand refrigerators. It is commonly used to secure panels, handles, shelves, or other parts of the refrigerator.

Causes of a faulty refrigerator screw can include wear and tear over time, damage due to mishandling or over-tightening, or loss of thread integrity. These factors can result in loose or ineffective connections, compromising the stability or functionality of the attached components.

Symptoms of a bad refrigerator screw may include:

• Loose or wobbly panels, handles, or shelves
• Difficulty in attaching or securing components
• Visible damage or breakage of the screw

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.