Parts for Ge GTS19KGNBRWW: Doors Parts

This white plastic door handle replaces a broken or worn handle on compatible refrigerators, restoring a secure grip and a clean, factory look so you can open and close the door confidently.

• Provides the handhold used to open and close the refrigerator door
• Replaces cracked, broken, loose, or missing handles to improve safety and appearance
• Attaches to existing mounting points with model-specific fasteners or set screws
• Helps eliminate wobble or rattling caused by a damaged handle

• Disconnect power at the breaker before starting for safety
• Support the handle while loosening existing fasteners; note their positions and orientation
• Align the new handle; start screws by hand, then tighten evenly without overtightening
• If your model uses trim caps, install them after tightening

The Freezer Door Gasket is an OEM component specifically designed for GE side-by-side refrigerators. This gasket helps create an air-tight seal between the freezer door and the body of the refrigerator. 

The gasket is responsible for ensuring cold air stays trapped inside the freezer compartment. Its flexible and durable design allows it to contour perfectly to the door frame. 

Symptoms of a bad gasket include:

• Cold air leaking from the freezer 
• The door not sealing properly 
• Increased frost or ice buildup
• Higher energy bills

If left unaddressed, a defective gasket can compromise cooling efficiency and negatively impact your electric bill. This OEM GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

This freezer door stop is a small plastic bumper that cushions and limits the freezer door's travel to prevent over-extension and reduce slamming. It restores proper door positioning and helps protect the cabinet edge. What it does:

• Acts as a door bumper/stop so the freezer door closes and rests correctly
• Reduces slamming and wear on the door and cabinet edge
• Helps keep the door aligned during normal opening and closing
• Can resolve symptoms like a door that over-rotates, hits the cabinet, or doesn't seat cleanly

• One white freezer door stop

• Typically installs by snapping or sliding into the hinge/cabinet mounting location; verify orientation before pressing into place
• Turn power to the appliance off only if panel removal is required; this part is non-electrical
• Use basic hand tools if needed and avoid forcing the part to prevent breakage

This refrigerator door stop cushions and limits the door swing to prevent over-travel and protect the cabinet and hinge. Durable plastic design restores proper door alignment and reduces slamming for a quieter, safer fridge. What it does

• Replaces a worn or broken door stop to stop the door from swinging too far.
• Helps prevent damage to the cabinet edge and hinge by absorbing impact.
• Reduces door noise and improves door alignment for a consistent seal.
• Commonly used where the original plastic stop is cracked, missing, or worn.

• One refrigerator door stop (white), as shown.

• Basic hand tools typically required; disconnect power only if working near electrical components.
• Keep original fasteners; replace only with like hardware if specified.
• Inspect surrounding hinge and mounting area for wear and replace if necessary.

This white gasket seals the refrigerator's fresh food compartment door. Replacing a worn or torn seal restores a tight closure, helping keep cold air in, reduce condensation, and maintain consistent temperatures for better performance and food preservation.

• Creates an air-tight seal between the fresh food door and cabinet to prevent air leaks
• Helps maintain proper temperature and humidity in the refrigerator section
• Reduces moisture, frost, and energy loss around the door opening
• Common symptoms of a failed gasket include cracks, warping, gaps, loose corners, moisture around the seal, or the door not closing flush

• Unplug the refrigerator before servicing
• Remove the old gasket from the door channel/retainer and clean the sealing surfaces
• Warm and relax the new gasket (room temperature or soak in warm water); start at the corners, then press evenly into the channel
• Close the door and check the seal with a paper test; apply gentle heat to smooth folds and improve contact if needed

This reversible door plug fills the unused mounting hole when you switch the door swing on your refrigerator. It restores a finished appearance and helps keep air and moisture from entering through the opening.

• Covers the unused door hole created during a door swing reversal
• Helps maintain proper sealing and resists drafts/condensation at the opening
• Restores a clean, finished, factory look to the door
• Common symptoms: missing or cracked plug, exposed hole, cosmetic gap on door edge

• Disconnect power before servicing any door components
• Gently pry out the old plug with a plastic trim tool to avoid scratches
• Align the new plug with the opening and press until fully seated and flush
• Verify the door closes properly and the gasket seals evenly

This kit replaces the mounting hardware that secures a refrigerator/freezer door handle to the door, restoring a solid, safe grip and clean appearance when the original fasteners are missing, damaged, or stripped.

• Provides the correct hardware to attach and secure the door handle
• Helps resolve loose, wobbly, or detached handles
• Replaces missing, damaged, or stripped handle fasteners
• Supports proper handle alignment and feel

• Disconnect power (and water, if applicable) and wear gloves.
• Support the handle while removing old hardware to prevent drops or scratches.
• Start threads by hand to avoid cross-threading; tighten evenly and do not overtighten.
• The handle is secure and the door opens/closes normally.

This plug button is a small snap-in cap used on refrigerators to cover exposed holes on door handles, liners, or trim. It restores a clean, finished look while helping keep dust and moisture out of the cabinet.

• Snaps into a screw or access hole on a handle, liner, or trim panel
• Covers fasteners and gaps for a clean, finished appearance
• Helps block dirt and moisture from open holes
• Typical symptoms: missing cap, broken or loose plug, visible screw hole or cosmetic gap

• Unplug the appliance before servicing and use caution around sharp edges
• Align the plug with the hole and press straight in by hand until fully seated and flush
• For handle screw holes, tighten fasteners first, then install the cap
• Avoid using metal tools on finished surfaces to prevent scratches

The Screw is an OEM replacement part for GE brand refrigerators. It is commonly used to secure panels, handles, shelves, or other parts of the refrigerator.

Causes of a faulty refrigerator screw can include wear and tear over time, damage due to mishandling or over-tightening, or loss of thread integrity. These factors can result in loose or ineffective connections, compromising the stability or functionality of the attached components.

Symptoms of a bad refrigerator screw may include:

• Loose or wobbly panels, handles, or shelves
• Difficulty in attaching or securing components
• Visible damage or breakage of the screw

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.