Parts for Frigidaire FEW30S2DCB: 05 - Drawer Parts

This warmer drawer assembly replaces a failed or damaged warming drawer to restore the appliance's ability to keep cooked foods warm and ready to serve. Fits as a direct replacement for units using this OEM drawer assembly. What it does:

• Provides the insulated, heated compartment that maintains cooked-food temperature for serving
• Replaces cracked, bent or non-sealing drawers that allow heat loss
• Restores proper drawer movement and latch engagement for safe use
• Helps eliminate intermittent or complete loss of the warming function when the drawer assembly is damaged

• Disconnect power to the appliance before starting any repairs to avoid shock
• Handle the drawer carefully—edges and mounting tabs may be sharp
• Verify proper seating and alignment; ensure connectors and mounting clips engage fully
• If wiring or heating elements are exposed or damaged, replace those components per OEM instructions.

Replacement handle for range oven doors. Mounts to the front exterior of the door for opening and closing. Replace if cracked, broken, or loose.

This metal rack fits inside the warming drawer beneath the oven, providing a flat surface to hold plates, dishes, or cooked food at a warm serving temperature. It slides in and out of the drawer on built-in guides. Replace it if the rack is bent, warped, rusted, or missing, which can prevent proper food placement and even heat distribution in the warming drawer.

This control panel is the exterior console that holds your appliance's controls and provides a finished look. Replacing a damaged panel restores button access and improves appearance. What it does:

• Houses the user controls and buttons so you can operate the appliance
• Protects the underlying electronic controls from everyday wear and spills
• Restores readable legends and button responsiveness if the panel is cracked, warped, or faded
• Helps resolve issues where buttons are stuck, missing, or cosmetically damaged

• One replacement control panel

• Disconnect power to the appliance before starting any repair
• Handle panel edges and any glass or plastic trim carefully to avoid cuts or damage
• Installation typically requires removing the console bezel and a few mounting screws
• Retain all fasteners and note wire/connector locations for reassembly

Cushioned fastener washer that protects surfaces and reduces vibration. Replace if cracked, compressed, or missing to prevent metal damage and loosening.

Mounting screw for ranges, ovens, and cooktops. Secures panels, brackets, or internal components. Replace if missing, stripped, or damaged.

Cushioned fastener washer that protects surfaces and reduces vibration. Replace if cracked, compressed, or missing to prevent metal damage and loosening.

Mounting screw for ranges, ovens, and cooktops. Secures panels, brackets, or internal components. Replace if missing, stripped, or damaged.

Specs: 8 - 18 x 0.500

Specs: 8 - 18 x 0.500

This replacement screw secures appliance panels, brackets, and internal components. It restores a tight, rattle-free fit and proper alignment when an original fastener is missing, stripped, or corroded.

• Fastens metal or plastic parts to the cabinet/frame
• Helps maintain alignment and reduce vibration or rattling
• Direct replacement for lost, damaged, or rusted hardware
• Keeps covers and brackets safely in place

• Disconnect power before servicing; for gas appliances, also shut off gas supply
• Match one-for-one with the original screw; verify length/type before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver bit to prevent stripping the screw head

This replacement screw secures appliance panels, brackets, and internal components. It restores a tight, rattle-free fit and proper alignment when an original fastener is missing, stripped, or corroded.

• Fastens metal or plastic parts to the cabinet/frame
• Helps maintain alignment and reduce vibration or rattling
• Direct replacement for lost, damaged, or rusted hardware
• Keeps covers and brackets safely in place

• Disconnect power before servicing; for gas appliances, also shut off gas supply
• Match one-for-one with the original screw; verify length/type before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver bit to prevent stripping the screw head