Parts for Craftsman 358795180: Driveshaft Parts

Designed for use with a wide range of string trimmers, this momentary switch is a genuine OEM replacement part. A momentary switch, also known as a kill switch, is a safety precaution that kills an appliance's engine in a moment, even if the engine is not set to the off position. This helps prevent accidents if the operator begins to lose control of the trimmer. At the touch of a button, the engine cuts and cannot be restarted for a short period (usually about five seconds). Momentary switches are positioned in a way that they don't often sustain damage but, over time, they can wear out. Once a switch stops working, it will need to be replaced to ensure safe operation. This is a fairly straightforward fix that only requires a screwdriver to open the tiller's handle and pliers to safely remove the wiring. This part is designed for string trimmers made by Poulan, Weed Eater, Paramount, and Husqvarna. It ships individually of any other hardware is comes sourced from the original manufacturer.

This part is a handlebar clamp that is used on line trimmers and edgers. The purpose of the handlebar clamp is to essentially clamp the handlebar to the tube shaft. This component can be adjusted up or down along the length of the tube.A new handlebar clamp will be needed if the original is cracked, broken, missing, or damaged in any way. This component may become damaged over time due to normal wear and tear over a period of time. Remember to wear gloves when operating or performing care and maintenance on any outdoor power equipment. Never perform care and maintenance on outdoor power equipment that is powered on.This handlebar clamp is a genuine Husqvarna part. It is sold individually. This particular handlebar clamp is compatible with line trimmers and edgers that are manufactured by Husqvarna, Poulan, and Weed Eater.

This part is a handlebar clamp that is used on line trimmers and edgers. The purpose of the handlebar clamp is to essentially clamp the handlebar to the tube shaft. This component can be adjusted up or down along the length of the tube.A new handlebar clamp will be needed if the original is cracked, broken, missing, or damaged in any way. This component may become damaged over time due to normal wear and tear over a period of time. Remember to wear gloves when operating or performing care and maintenance on any outdoor power equipment. Never perform care and maintenance on outdoor power equipment that is powered on.This handlebar clamp is a genuine Husqvarna part. It is sold individually. This particular handlebar clamp is compatible with line trimmers and edgers that are manufactured by Husqvarna, Poulan, and Weed Eater.

This part is a handlebar clamp that is used on line trimmers and edgers. The purpose of the handlebar clamp is to essentially clamp the handlebar to the tube shaft. This component can be adjusted up or down along the length of the tube.A new handlebar clamp will be needed if the original is cracked, broken, missing, or damaged in any way. This component may become damaged over time due to normal wear and tear over a period of time. Remember to wear gloves when operating or performing care and maintenance on any outdoor power equipment. Never perform care and maintenance on outdoor power equipment that is powered on.This handlebar clamp is a genuine Husqvarna part. It is sold individually. This particular handlebar clamp is compatible with line trimmers and edgers that are manufactured by Husqvarna, Poulan, and Weed Eater.

This screw is a genuine MTD part, sold individually. This screw can be used as a replacement part in string trimmers, edgers, chainsaws, and pole pruners.The screw in a small engine outdoor appliance might eventually have to be replaced in the case that the screw is lost, misplaced, or damaged from general wear and tear with long-term use. If the screw is lost or misplaced and its absence is noted by the operator, the screw should be replaced by this genuine OEM replacement part as soon as possible. If the screw is dented, cracked, punctured, or otherwise damaged, it should be replaced by this genuine OEM replacement part.This is a genuine OEM replacement part sourced directly from the manufacturer. It is sold individually. This screw is compatible with the following outdoor appliance brands: MTD, Craftsman, Husqvarna, Weed Eater, Poulan, and Poulan Pro.

This part is a replacement washer. This is a genuine OEM part made by Husqvarna and has been sourced directly from the manufacturer. This part can be used to replace a broken or misplaced washer in a variety of outdoor power equipment, although it is primarily intended for use with line trimmers. Washers provide a better bearing surface for a screw or bolt. Over time, washers can easily become corroded, broken, or misplaced, requiring replacement. It's important when working on or near any engine to make sure the equipment is powered off and completely cooled down before starting any repairs. For more accurate information on how and where to install this washer, the appropriate owner's manual and equipment diagrams should be referred to. As an authentic replacement part, this washer is suitable for use on several models of line trimmers and other outdoor power equipment manufactured by Husqvarna, Poulan, and other brands. This is a genuine part made of high-quality, durable metal and is sold individually.

This replacement screw is intended for use on a variety of lawn and garden tools to attach components. It is a genuine OEM part sourced directly from the manufacturer. It is used to attached the trimmer head to the shaft in weed eaters and in many other applications on other tools. Overuse and normal wear and tear can cause damage to the screw. The screw can also become stripped when it is over-tightened or bent from contact with heavy debris. The screw will need to be replaced if this happens. Routinely inspecting equipment will help reveal broken or missing screws that need to be replaced or tightened. This screw is a star-slotted screw that requires a Torx screwdriver to remove it from the machinery. If the screw is in a tight-fitting area, an extension socket with a Torx bit can be used to remove the screw and to install a new one. When replacing a screw, check the remaining screws for damage and tighten any that are loose. This screw is a silver-colored, heavy-duty metal screw sold individually. It is compatible with trimmers, leaf blowers, leaf vacuums, hedge trimmers, and other equipment manufactured by Craftsman, Weed Eater, Poulan, and Husqvarna.

This trigger is used on trimmers and pruners. By applying different levels of pressure to the trigger, the operator can control how fast or slow the motor inside the device will operate. Pulling the trigger engages the throttle, which directs the lawn equipment to work harder. Releasing pressure slows down the operation. The trigger may wear out or become damaged through use, from dropping, or by accident. A trigger replacement is required to use the equipment, as it won't function safely or correctly without it.Wear gloves when replacing the trigger. The process is completed quickly and easily by attaching the replacement trigger to the throttle cable. Be sure the throttle cable is attached to the carburetor accurately first. Check the manufacturer manual for precise instructions on installation.This trigger is a genuine OEM part that can be used in Husqvarna, Craftsman, Poulan, Weed Eater, AYP, Jonsered, RedMax, and McCulloch products. It is sold individually. The trigger is made of durable, high-quality plastic. The part is for lawn tools and equipment, including various trimmers and some pruners. If a screw is required to complete the installation, it must be purchased separately.