Parts for Frigidaire DE24P2WTFA: 03 - Drum And Blower Parts

This part has been discontinued by the manufacturer and is no longer available.

Mounting screw for dryer assembly and panel installation. Replace if stripped, missing, or corroded. Essential hardware for secure component attachment.

Mounting screw for dryer assembly and panel installation. Replace if stripped, missing, or corroded. Essential hardware for secure component attachment.

Mounting screw for dryer assembly and panel installation. Replace if stripped, missing, or corroded. Essential hardware for secure component attachment.

Mounting screw for dryer assembly and panel installation. Replace if stripped, missing, or corroded. Essential hardware for secure component attachment.

Mounting screw for dryer assembly and panel installation. Replace if stripped, missing, or corroded. Essential hardware for secure component attachment.

Mounting screw for dryer assembly and panel installation. Replace if stripped, missing, or corroded. Essential hardware for secure component attachment.

A small molded clip that secures appliance wiring and harnesses to the cabinet, helping keep wires in place and reducing wear or rubbing. Use this clip when a loose or shifted harness needs a reliable anchor point. What it does:

• Fastens wiring or harnesses to the cabinet to prevent movement and chafing
• Keeps wires routed away from heat, moving parts, and sharp edges
• Helps reduce vibration noise caused by loose wiring
• Can prevent intermittent electrical issues caused by damaged insulation or connectors

• Disconnect power before accessing internal wiring or panels
• Remove the panel or trim needed to reach the original clip location
• Press the clip into the factory mounting hole or snap the wire into the clip until secure
• Inspect nearby wiring and harnesses for damage; replace any damaged wiring before reassembly

This small retainer clip secures trim and components to the appliance chassis, keeping panels and assemblies properly seated for quiet, reliable operation. It's a simple replacement that restores secure fastening where the original clip has broken or worn. What it does

• Holds panels, trim pieces, or small assemblies in place to prevent looseness and rattling
• Replaces a broken, bent, or missing clip that allows parts to shift during use
• Helps maintain proper alignment of adjacent components for smooth operation
• Works where a firm, non-permanent fastener is required

• One retainer clip

• Disconnect power before servicing any appliance to avoid shock or injury
• Access the clip location by removing the appropriate trim or panel per your model's service instructions
• Use needle-nose pliers or a flat screwdriver to remove the old clip and press the new clip into place until it seats securely

Harness cable tie secures and organizes wiring inside your appliance. Replace if damaged, cracked, or no longer holding wires firmly in place.

This part has been discontinued by the manufacturer and is no longer available.

This part has been discontinued by the manufacturer and is no longer available.

If your range hood isn't venting properly or has weak airflow, a damaged blower wheel is often the cause. This wheel circulates air through your range.

Mounting screw for dryer assembly and panel installation. Replace if stripped, missing, or corroded. Essential hardware for secure component attachment.

Mounting screw for dryer assembly and panel installation. Replace if stripped, missing, or corroded. Essential hardware for secure component attachment.

Mounting screw for dryer assembly and panel installation. Replace if stripped, missing, or corroded. Essential hardware for secure component attachment.

This part has been discontinued by the manufacturer and is no longer available.

This part has been discontinued by the manufacturer and is no longer available.

This part has been discontinued by the manufacturer and is no longer available.

Mounting screw for dryer assembly and panel installation. Replace if stripped, missing, or corroded. Essential hardware for secure component attachment.

Mounting screw for dryer assembly and panel installation. Replace if stripped, missing, or corroded. Essential hardware for secure component attachment.

Mounting screw for dryer assembly and panel installation. Replace if stripped, missing, or corroded. Essential hardware for secure component attachment.

Mounting screw for dryer assembly and panel installation. Replace if stripped, missing, or corroded. Essential hardware for secure component attachment.

Mounting screw for dryer assembly and panel installation. Replace if stripped, missing, or corroded. Essential hardware for secure component attachment.

Sems screw for washer assembly. Secures internal components and panels. Replace if missing, stripped, or damaged during appliance repair or maintenance.