Parts for QFD15ESSN0WW: Drum Parts

Replacement screw set for securing the front panel to your dryer or washer chassis. Install when original screws are stripped, missing, or damaged.

A small replacement housing screw that secures appliance panels and brackets, restoring proper fit and preventing rattles or loose panels. Fits common appliance housings where a short ST4 x 12 self-tapping screw is required. What it does:

• Fastens housing panels, trim, or internal brackets to maintain proper alignment and reduce vibration
• Replaces missing or damaged screws that cause loose or rattling panels
• Works with sheet metal and plastic mounting points designed for ST4 thread size
• Small, low-profile head designed for appliance interiors

• One housing screw (ST4 x 12)

• Disconnect power before servicing the appliance and work on cool surfaces
• Use the correct screwdriver or bit to avoid stripping the head
• Install gently and avoid overtightening to prevent thread or panel damage

Lint buildup or poor airflow? This dryer lint filter traps debris during drying cycles and prevents blockages. Easy DIY installation in minutes.

This front air duct directs cold air from the evaporator into the refrigerator cabinet to help maintain even cooling and airflow across shelves. It replaces a cracked, warped or missing duct to restore proper air distribution. What it does

• Channels cold air from the evaporator into the fresh-food compartment for more consistent temperatures.
• Helps prevent uneven cooling and warm spots on shelves and in door bins.
• Can reduce frost or ice buildup caused by disrupted airflow when the original duct is damaged.
• Restores correct airflow paths that can affect defrost and cooling performance.

• Disconnect power to the appliance before starting any service.
• Typically installs behind the fresh-food compartment trim or evaporator cover; remove panels and shelves as needed for access.
• Handle plastic parts and mounting tabs carefully to avoid breakage; use appropriate hand tools.

This drying rack hanger is a replacement support bracket that secures the appliance's drying rack in place so the rack stays aligned and functional. It restores proper support for removable drying racks and prevents sagging. What it does:

• Secures the drying rack to the appliance frame so the rack stays level and supported
• Prevents the rack from dropping, sagging, or shifting during use
• Restores smooth rack operation when hanger wear or breakage causes instability
• Helps eliminate rubbing or catching noises caused by a loose or broken hanger

• Disconnect power to the appliance before beginning work to avoid shock or injury
• Basic tools (screwdriver, pliers) may be required; follow OEM instructions for access
• Inspect adjacent rack hardware and replace damaged clips or fasteners as needed

Secures water tubing to the washer cabinet to prevent vibration and wear. Replace if your retainer clip is cracked, broken, or missing for proper line routing.

A standard M10 hex nut used to secure M10-threaded fasteners on compatible appliances. Replaces worn or missing nuts to restore secure connections and reduce rattling or looseness. What it does:

• Secures M10 bolts or studs to hold components together
• Helps eliminate movement that can cause vibration or noise
• Restores proper fit where a damaged or missing nut caused instability
• Used anywhere an M10 nut is specified by the manufacturer

• Use the correct wrench or socket to avoid rounding the nut
• Tighten until secure—follow OEM torque specs when available
• Disconnect power and follow safety instructions when working near electrical components

A small M10 nut with an integrated gasket that secures and seals threaded appliance connections to help prevent leaks and hold fittings tight. Compact replacement for worn or damaged sealing nuts. What it does:

• Provides a sealed threaded connection between hoses or fittings and appliance ports
• Compresses the gasket to prevent water or air leaks at the joint
• Keeps fittings securely fastened to reduce vibration and loosening
• Commonly replaced when threads are corroded, gasket is crushed, or leaks are present

• One M10 nut with bonded gasket

• Disconnect power and shut off water supply before servicing
• Hand-start the nut to avoid cross-threading, then snug with the correct sized wrench
• Inspect mating threads and sealing surface; replace if damaged or corroded
• Test the connection for leaks after reassembly

Fix a noisy or wobbling dryer drum with this drum support shaft. Holds the drum wheel in place for smooth spinning and proper alignment. Simple fix.

Supports the dryer drum and allows smooth rotation. Replace if cracked, worn flat, or causing the drum to wobble. Installs on the axle at rear or front.

This M6-14 metric machine bolt secures components and panels in appliances to restore proper fit and reduce movement. It's a direct-fit fastener used where a small metric bolt is required. What it does:

• Fastens panels, brackets, or components to maintain proper alignment and stability
• Replaces missing, stripped, or damaged bolts that cause rattling or loose parts
• Helps prevent wear from parts rubbing or shifting during operation

• One M6-14 metric bolt

• Disconnect power before working on the appliance
• Use the correct metric socket or driver to avoid stripping the head
• Tighten securely but avoid over-torquing to prevent thread damage

Secures and aligns the front drum edge for smooth rotation. Replace if you notice rubbing, noise, or uneven drum movement. Confirm fit with your model number.

This flat gasket is a thin sealing strip that restores a tight seal where two appliance surfaces meet, helping reduce leaks, drafts, and heat loss. Replace a worn gasket to improve performance and maintain safe operation. What it does

• Creates a flat, compressible seal between mating surfaces to help prevent moisture, food particles, or heat transfer.
• Commonly replaced when the original gasket is cracked, flattened, or no longer seats properly.
• Can reduce odors, dripping, or reduced thermal efficiency caused by a failing seal.
• Designed to match OEM shape and thickness for a proper fit when installed as directed.

• One flat gasket (quantity: 1).

• Inspect mating surfaces and clean thoroughly before installing the new gasket to ensure a good seal.
• Handle carefully to avoid stretching or tearing the gasket during installation.
• If adhesive or fasteners are used on the original gasket, use the same type per manufacturer guidance.
• Disconnect power and follow all safety instructions for your appliance before starting repairs.

A small M6 threaded nut that secures components and panels on compatible appliances, restoring proper fit and preventing loose hardware. Fits applications that use an M6 fastener for reliable, low-profile fastening. What it does:

• Secures bolts or studs with M6 threads to hold panels, brackets, or assemblies in place
• Stops rattling or movement caused by a missing or stripped nut
• Restores proper alignment where an M6 nut is required for safe operation
• Works where a standard M6 nut is specified by the manufacturer

• One M6 nut

• Disconnect power and water before accessing the repair area
• Replace only with the same thread size (M6) and style to ensure proper fit
• Hand-start the nut to avoid cross-threading, then tighten with the appropriate wrench or socket
• Do not overtighten; follow OEM torque if specified in service documentation

Houses and secures the lint trap in your dryer. Replace if cracked, broken, or allowing lint bypass. Confirm fit with your model number before ordering.