Parts for Craftsman 917251472: Engine 460777-1297-01 (71,500) Parts

This part is a magnetron that is used on microwave units. This part is responsible for producing the microwaves that cook the food inside of the unit. In the event that the microwave does not heat, it is likely that the magnetron will need to be replaced. The magnetron could burn out if the microwave oven has been run while it was empty. If this is the case, this part will be a high-quality replacement part. Microwaves contain high-voltage capacitors that can retain a lethal electrical charge, even if the unit is unplugged. Use extreme caution when working on this product.This particular magnetron is compatible with microwave ovens that are manufactured by the Bosch brand. It is sold individually. Since it is sourced straight from the manufacturer, it is a genuine OEM replacement part.

This drip pan is a replacement moisture-collection tray that sits under the refrigerator/freezer to catch condensation and defrost water, helping prevent puddles and damage to flooring. It restores the appliance's intended water management. What it does

• Collects and channels defrost and condensation water to the drain or evaporation area.
• Helps prevent water pooling beneath the appliance that can cause stains or floor damage.
• Reduces risk of water contacting electrical components or creating odors from standing water.
• Fits into the appliance's lower cabinet area where the original pan was located.

• One replacement drip pan.

• Disconnect power to the appliance before accessing the lower cabinet or removing panels.
• Remove any kickplate or lower access panel to reach the existing pan; lift out and replace with the new pan.
• Verify proper seating and alignment so water flows to the drain/evaporation area; do not force into place.
• If you find corrosion, cracks, or related component damage, inspect surrounding drain lines and mounting hardware and replace as needed.

This replacement part is a needle and seat kit. This part is a genuine replacement part made by Midwest Engine. This part is typically used as a part of the carburetor. This kit contains a brass plug with a shaped hole to accommodate the needle that also comes with it. These parts work together so that no fuel can enter the float bowl during use. This keeps the engine running smoothly. A new needle and seat kit might be needed if the current one is not working properly. If the user notices that the carburetor is having issues, it may be due to the needle and seat kit. Be sure the engine is completely turned off before starting this repair. This part is sold individually and is sourced directly from the manufacturer to ensure proper fit. This specific part is a genuine OEM replacement part for long-lasting use.

This hinge is the OEM replacement that supports and pivots your appliance door for proper alignment and smooth opening. Replacing a worn hinge restores correct door fit and helps prevent sagging or binding. What it does:

• Provides a pivot point for the appliance door to open and close smoothly
• Maintains door alignment and seal to help prevent leaks or uneven gaps
• Worn or damaged hinges can cause the door to sag, rub, or close unevenly
• Matches OEM fit and mounting points for direct replacement

• Disconnect power and water before inspecting or replacing door hardware
• Support the door during removal to prevent dropping or damage
• Compare new hinge to the old part for correct orientation and mounting before final installation
• Tighten fasteners securely but avoid over-torquing; test door operation after installation

This replacement tube is a direct-fit connector used to route water or other fluids within the appliance, restoring proper flow and sealing to help prevent leaks and interruptions in operation. What it does:

• Routes water or fluid between components to maintain proper system flow
• Provides a sealed connection to help prevent drips and leaks
• Replaces cracked, split, or clogged tubing that can cause poor performance
• Helps stop intermittent water flow interruptions or unexpected leaks

• One replacement tube/connector as shown

• Install only when the appliance is powered off and water supply is shut off
• Confirm orientation and seating to avoid pinches or kinks that can restrict flow
• Use compatible clamps or fittings provided by the appliance manufacturer

This is a high-quality starter motor that is used for small engines installed on a variety of lawnmower models. The starter motor is responsible for providing initial motion, which causes the flywheel to engage and start the engine. The starter motor is located on the engine crankcase and makes the flywheel teeth connect with the starter motor plunger teeth to power up the engine. A bad starter motor can have many symptoms, including a clicking noise when the ignition is pressed, cranking noises without engine turnover, or a lawnmower that does not start.If the starter motor needs to be replaced, the lawnmower will need to be disassembled to access the part. Remove the shroud, disconnect the battery, and remove the fan. The flywheel can be removed using a gear puller, after which the wire and bolts should be removed. Next, remove the starter motor and replace it with a new part.This starter motor is an authentic OEM replacement component that is directly sourced from the manufacturer. It is sold as an individual part. The motor is designed for use with lawnmowers manufactured by Briggs & Stratton, Craftsman, Cub Cadet, Toro, and Simplicity.

This electronic control unit directs and coordinates the appliance's operation. It interprets inputs from the controls and sensors and switches power to key components, helping restore proper response and reliable performance when the original board fails. What it does:

• Processes user inputs and sensor signals to manage functions and timing
• Drives relays/switching to power components such as motors, heaters, valves, or fans
• Stores the control logic for modes and settings
• Typical symptoms include no response to controls, won't start, intermittent shutdowns, or error codes

• 1 electronic control unit (board/module)

• Disconnect power at the breaker or unplug the appliance before servicing
• Use ESD precautions; handle the board by the edges to avoid static damage
• Label/photograph all connectors and transfer any brackets or covers from the original board
• Ensure all connectors are fully seated before reassembly and testing

This is an oil filter that facilitates the removal of harmful contaminants from the engine oil. This part is designed to help maintain the optimum performance of an engine in compliance with the necessary EPA emissions regulations. It is recommended that the oil filter is replaced annually or every 100 hours. Remember to prepare something to catch the oil when replacing the oil filter. The old one will need to be unscrewed to replace it, but be sure to coat the seal of the new filter with oil before installing it. To ensure that the new oil filter is in place, make sure it touches the plate it seals against by giving the filter a firm turn to tighten it down. This replacement part is an individual genuine OEM part. It is compatible with small engines, lawnmowers, generators, snowblowers, and wood chippers from Toro, Lawn-Boy, Simplicity, Snapper, and Briggs & Stratton.