Parts for Craftsman 41CDZ45C799: Engine Assembly Parts

This replacement part is a primer bulb. It is a genuine replacement part made by MTD. Primer bulbs are found in many types of machines that use engines to function. This part is a rubble button that is pressed to prime the engine before it is actually started. It also sometimes helps to fill the carburetor with the correct amount of fuel so that everything starts correctly. A new primer bulb might be needed if the user notices that the engine is not starting or slow to start. This can be because of normal wear and tear. Be sure the engine is shut down completely before replacing this part. This primer bulb is a genuine OEM replacement part to ensure long-lasting use. This part is sold individually and is sourced directly from the manufacturer to ensure proper fit.

This starter recoil is a genuine MTD part, sold individually. This starter recoil can be used as a replacement part for a string trimmer. This starter recoil facilitates the powering on of the small engine of the string trimmer through a pull system in which the pull cord is tugged by the operator of the string trimmer. If the starter recoil is not turning on the engine when the cord is pulled, it is likely that the starter recoil needs to be removed and replaced with this genuine OEM replacement part.This is an OEM part sourced directly from the manufacturer. It is sold individually. This starter recoil is compatible with the following outdoor appliance brands: MTD and Craftsman.

This part is a replacement screw. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. This part can be used to replace a stripped or misplaced screw in a variety of outdoor power equipment. This screw is a genuine piece of standard hardware that can have many potential uses. It's important to use screws sourced from the manufacturer to ensure a proper fit and high quality. Screws are essential for securing parts and holding the equipment together and should be replaced if worn, broken, or lost. It is always recommended that the appropriate safety precautions are adhered to when attempting to fix any power tools or machinery. When working on or near an engine, ensure the equipment is powered off and completely cooled down before starting any repairs. For more accurate information on how and where to install this screw, the appropriate owner's manual and included diagrams should be referenced.As an authentic replacement part, this screw is suitable for use on several different models of blowers, edgers, and trimmers manufactured by MTD, Ryobi, Yard Man, Cub Cadet, and Troy-Bilt. This is a genuine part made of high-quality, durable metal and is sold individually.

This replacement part is a boot assembly and is intended for use in different types of lawn equipment. This is a genuine replacement part made by MTD. This boot assembly is sometimes referred to as a carburetor intake boot assembly and is found specifically in line trimmers or edgers. This part helps the carburetor run and allows the engine to work properly and efficiently. A new carburetor intake boot assembly might be needed if the current one is damaged or broken in any way including being dented, cracked, chipped, or snapped. This can create problems for the carburetor and the engine can be affected. Be sure to wear work gloves during this repair and double check to make sure the engine is completely powered off and cooled down before starting. This is a genuine OEM replacement part and is sourced directly from the manufacturer to ensure a proper fit. This part is sold as a single set.

This is a screw that is used for many pieces of lawn and garden equipment in a host of different ways. Screws such as this one are used to hold two components together. If the screw is not affixed properly or if there is an issue with the screw itself, it could affect the stability of the machine. If it is missing or not tight, it might also result in added noise when the machine is in use.Screws are made from metal and can last for a long time. However, if the threads are stripped or if the head of a screw wears down, it should be replaced. There is also the chance of corrosion or of losing the screw when working on the machine.This part is sold individually, and it can work well for a range of different machines from MTD, Craftsman, Bolens, and Yard Machines. This is a genuine OEM replacement part that is from the manufacturer.

This replacement part is a boot assembly and is intended for use in different types of lawn equipment. This is a genuine replacement part made by MTD. This boot assembly is sometimes referred to as a carburetor intake boot assembly and is found specifically in line trimmers or edgers. This part helps the carburetor run and allows the engine to work properly and efficiently. A new carburetor intake boot assembly might be needed if the current one is damaged or broken in any way including being dented, cracked, chipped, or snapped. This can create problems for the carburetor and the engine can be affected. Be sure to wear work gloves during this repair and double check to make sure the engine is completely powered off and cooled down before starting. This is a genuine OEM replacement part and is sourced directly from the manufacturer to ensure a proper fit. This part is sold as a single set.

This is a genuine replacement O-ring, which is a standard part on a number of engines. This O-ring is specifically designed as a replacement for the one found in the carburetor on select lawn and garden engines. The O-ring is designed to create a seal in the carburetor to ensure optimal performance and prevent leaks. It is also designed to help create the right amount of pressure. Over time, O-rings can become corroded, worn, or damaged due to their exposure to pressure and high heat. If they become broken or damaged, they can result in poor engine performance or even total engine failure. This genuine OEM O-ring is manufactured by RYOBI and compatible with a number of tillers, trimmers, and blowers from this brand. It is also designed for use with select models from Bolens, Yard Man, MTD, and Troy-Bilt. There are more than 150 models that can use this specific O-ring. It is made of durable materials and sold as an individual unit. Keep in mind that because O-rings have multiple applications and engines may have more than one type, it is important to double-check the location and application of the part to ensure the right one is being used.

This replacement part is a fuel tank intended for use in lawn equipment. This is a genuine replacement part made by MTD. Fuel tanks help keep the machine fuel safe and clean while providing a holding space for the liquid. If the fuel tank is not intact it is easy for dust, dirt, and other debris to contaminate the fuel.A new fuel tank might be needed if the current one is unable properly close so that the fuel is kept clean and safe. If the fuel tank is damaged or broken in any way, especially having cracks or holes, the user should consider replacing this part immediately. The fuel tank is an essential part to many lawn equipment and appliances. This is an OEM part sourced directly from the manufacturer. It is sold individually. This replacement part is compatible with lawn equipment made by MTD.

This fuel tank support is a genuine MTD part, sold individually. A fuel tank support can be used as a replacement part for outdoor appliances including tillers, string trimmers, leaf blowers, and edgers. This genuine OEM part is made out of high quality, durable materials that are specifically designed to last and hold up to possible general wear and tear over long-term usage.The fuel tank support might be subject to various forms of damage that can reduce or negate the efficacy of its function. If this occurs, the fuel tank support should be removed and replaced by this genuine OEM replacement part in order to guarantee safe continued usage of the appliance over its typical lifespan.This is a genuine OEM replacement part sourced directly from the manufacturer. It is sold individually. This fuel tank support is compatible with the following outdoor appliance brands: MTD, Craftsman, Cub Cadet, Troy-Bilt, and Yard Machines.

This throttle cable is a genuine MTD part, sold individually. This throttle cable can be used as a replacement part for string trimmers. The purpose of a throttle cable for a string trimmer is to allow the speed of the engine to be easily regulated when pulling on and engaging the cable.The throttle cable of a string trimmer might have to be replaced at some point within the standard lifespan of a string trimmer in the event that the component is not functioning as it usually does. This could be the case if the throttle cable is damaged in the form of tearing, ripping, fraying, or erosion to the material. If the speed of the engine is not being regulated by the throttle cable when pulled or engaged, the throttle cable should be removed and replaced by this genuine OEM replacement part. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This is an OEM part sourced directly from the manufacturer. It is sold individually. This throttle cable is compatible with the following outdoor appliance brands: MTD, Troy-Bilt, Cub Cadet, and Craftsman.

The clutch assembly uses centrifugal force to connect the shafts and create the drive shaft motion that powers the machine. The drive shaft nests inside the other shaft, and over time these parts can wear and become damaged with regular use. Today's parts can even continue to function long past when they should, so it may not be apparent that a clutch assembly needs to be replaced until the entire unit is bad. If the engine is not performing as it should or if the drive shaft seems unstable, it may be time to replace the clutch assembly. This genuine OEM part includes everything needed for the job. This OEM clutch replacement is designed for use with various cultivators, edgers, and trimmers. It can be used on machines from MTD, RYOBI, Troy-Bilt, Bolens, Yard-Man, Cub Cadet, Murray, and Husky. This assembly includes the clutch, clutch drum, washer, and left-hand threaded screw. Always disengage the spark plug and allow the engine to cool completely before beginning repairs.

This is a replacement module kit for use with gas trimmers. The module is an essential part of the machine since it produces the voltage that travels from the spark plug wire to the plug and then to the engine. If the module is going bad, it will be difficult or even impossible to get the trimmer started. Check the module and replace it if needed.The module is made from metal and plastic. It is usually a long-lasting piece, but it could still need to be replaced. It might be faulty and stop working, or it could be damaged. Regardless of the reason, owners will want to make a replacement. They will need to have a screwdriver, socket wrench, and a pair of pliers to help with the repair. They should wait until the engine is completely cool before starting the repair.This module is compatible with models of trimmers from Craftsman and MTD. The part is sold individually, and it is a genuine OEM replacement part.

This is a clutch cover assembly that is intended for use with trimmers. The assembly is made to fit over the clutch. This part helps to ensure that the clutch is not damaged or covered in debris when the trimmer is being used.The clutch cover assembly is made from durable materials, but it might still need to be replaced eventually. It could become cracked or broken, which would allow debris to get into the clutch. This could make the machine difficult or impossible to operate if the clutch is compromised. Disconnect the spark plug before beginning any repairs and wear gloves for safety.The clutch cover assembly will work with select trimmers from Craftsman, Troy-Bilt, and MTD. The cover is sold individually and is a genuine OEM replacement part that was sourced from the manufacturer.

This replacement part is a muffler assembly. It is a genuine replacement part made by MTD. Mufflers are commonly found in any machine that produces loud noise while in use. A muffler is there to help minimize and reduce the sound that comes out of the machine as to not distract the user from completing a specific job.A new muffler assembly might be needed if extremely loud noises are coming from the machine, especially if the machine was not always that noisy. It is possible that the muffler can become damaged or come detached from the machine itself, which would cause louder noises than what the user is used to.This muffler assembly is sold individually and is a genuine OEM replacement part and is sourced directly from the manufacturer. This ensures proper fit over time.

This is an MTD muffler screw designed to hold the cover of the muffler in place.The muffler screw is tightened in place in the center of the muffler cover using the proper screwdriver. Do not overtighten the screw, as this can cause potential damage and stripping. There should be no need for any extra fastening components to be added to the muffler.The part listed is a genuine OEM product and is sourced directly from the manufacturer. The component is sold individually. This product is compatible with MTD and Briggs and Stratton products.

This replacement part is a short block assembly. This is a genuine replacement part made by MTD. This short block assembly is part of the engine and contains the cylinder block near the gasket. This part ensures the engine is working properly overall. A new short block assembly might be needed if the current one is missing or damaged. It is common that this part might experience damage over time after years of normal use. When replacing this part, be sure the engine is completely shut off and cooled down. It is also recommended that work gloves are used when replacing or repairing any part near or around the engine. This is a genuine OEM replacement part. This part is sold individually and is sourced directly from the manufacturer.

This part is an oil fill plug. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. This part can be used to replace a broken or misplaced oil fill plug in a variety of trimmer models. The oil fill plug prevents oil from spilling out of the oil pan while the equipment is being used. If the plug is broken or is misplaced, oil can easily leak or spill from the pan, which can cause the engine to run out of oil and lead to more serious issues. Oil leaks are also inconvenient and messy to clean up. It is always recommended that the appropriate safety precautions are adhered to when attempting to fix any power tools or machinery. No special tools are necessary to replace this part. For more accurate information on how and where to install this oil fill plug, the appropriate owner's manual and included diagrams should be referenced.As an authentic replacement part, this oil fill plug is suitable for use on several different models of trimmers manufactured by MTD, Craftsman, and Troy-Bilt. This is a genuine part made of high-quality, durable materials and is sold individually.

This spark plug is a genuine Husqvarna part, sold individually. This spark plug can be used as a replacement part for outdoor appliances with small engines such as string trimmers and leaf blowers. This spark plug provides an ignition source for the engine.The spark plug might have to be replaced at some point in the standard lifespan of the appliance if it suffers enough damage to render it useless. The spark plug might be cracked, punctured, or eroded enough to reduce its functionality. If this occurs, the spark plug should be removed and replaced with this genuine OEM replacement part before using the appliance again. Remember to wear work gloves as a safety precaution while repairing or replacing parts within an outdoor appliance. This is an OEM part sourced directly from the manufacturer. It is sold individually. This spark plug is compatible with the following outdoor appliance brands: MTD and Craftsman.

This replacement part is an air filter. This is a genuine replacement part made by MTD. This filter is able to ensure that the air coming in and out of the machine is free of dust and other debris. This part is able to keep the engine safe and allows it to run smoothly. A new air filter might be needed if the current one is damaged or too dirty to clean. If the current part does not filter air properly, it might be best to replace it. If not up to working standard, the filter can cause the engine to become damaged if too much dust or debris gets inside. Be sure that the engine is completely shut down before replacing this part. This part is a genuine OEM replacement part. This part is sold individually and is sourced directly from the manufacturer to ensure proper fit.