Parts for Craftsman 41CDZ47C799: Engine Assembly Parts

Replace the top housing cover on your gas line trimmer. This protective shell encases internal components and can crack, break, or wear from impact and outdoor use.

This is a replacement primer bulb, made as a genuine part compatible with select trimmers designed for outdoor use. The primer bulb is a small part that is made of plastic and rubber, in most cases. It is designed to provide a quick injection of fuel directly into the carburetor in order to fire the engine and allow the unit to start. This can be helpful after the trimmer has been sitting for a season, or just for regular use. The primer bulb can become damaged or cracked over time or due to an impact. If that happens, it will not function properly and the engine will not be able to start smoothly since it is not primed. The bulb and plastic attachment are sold as a single piece for this unit, which is manufactured by MTD. This part does not require tools to replace, although a screwdriver may be helpful in removing the old component and putting the new one in place. Wear gloves for hand protection and remember to never perform work until the appliance has cooled completely.

Won't start or cord won't retract? This recoil starter assembly enables pull-start operation on gas trimmers. DIY-friendly repair in 15-20 minutes.

Replacement screw for outdoor power equipment including lawn tractors, tillers, leaf blowers, and trimmers. Replace stripped, missing, or damaged screws.

O-ring seal for gas line trimmers. Replace when you notice fuel leaks or dried, cracked seals. Verify fit with your model number for proper sealing.

Intake insulator for gas line trimmers. Mounts between carburetor and engine block to prevent heat transfer. Replace if cracked, melted, or missing.

Carburetor intake boot assembly for gas line trimmers. Connects carburetor to engine. Replace if cracked, torn, or causing air leaks. Genuine part.

Fastener screw for tillers and lawn equipment. Secures components together for stable operation. Replace if stripped, missing, or damaged during maintenance.

Replace your gas line trimmer air cleaner assembly to filter dust and debris from the engine. Install when filter is clogged or damaged. Verify fit with model number.

Engine won't start or runs rough? This gas line trimmer carburetor mixes air and fuel for proper combustion. Includes choke and throttle controls.

This is a genuine replacement O-ring, which is a standard part on a number of engines. This O-ring is specifically designed as a replacement for the one found in the carburetor on select lawn and garden engines. The O-ring is designed to create a seal in the carburetor to ensure optimal performance and prevent leaks. It is also designed to help create the right amount of pressure. Over time, O-rings can become corroded, worn, or damaged due to their exposure to pressure and high heat. If they become broken or damaged, they can result in poor engine performance or even total engine failure. This genuine OEM O-ring is manufactured by RYOBI and compatible with a number of tillers, trimmers, and blowers from this brand. It is also designed for use with select models from Bolens, Yard Man, MTD, and Troy-Bilt. There are more than 150 models that can use this specific O-ring. It is made of durable materials and sold as an individual unit. Keep in mind that because O-rings have multiple applications and engines may have more than one type, it is important to double-check the location and application of the part to ensure the right one is being used.

Replace a cracked or leaking fuel tank causing fuel smell, poor engine performance, or visible damage. Direct fit tank keeps fuel clean and secure.

This fuel tank support is a genuine MTD part, sold individually. A fuel tank support can be used as a replacement part for outdoor appliances including tillers, string trimmers, leaf blowers, and edgers. This genuine OEM part is made out of high quality, durable materials that are specifically designed to last and hold up to possible general wear and tear over long-term usage.The fuel tank support might be subject to various forms of damage that can reduce or negate the efficacy of its function. If this occurs, the fuel tank support should be removed and replaced by this genuine OEM replacement part in order to guarantee safe continued usage of the appliance over its typical lifespan.This is a genuine OEM replacement part sourced directly from the manufacturer. It is sold individually. This fuel tank support is compatible with the following outdoor appliance brands: MTD, Craftsman, Cub Cadet, Troy-Bilt, and Yard Machines.

Throttle control cable for gas line trimmers. Connects the throttle trigger to the engine carburetor. Replace if cable is frayed, stuck, or broken.

The clutch assembly uses centrifugal force to connect the shafts and create the drive shaft motion that powers the machine. The drive shaft nests inside the other shaft, and over time these parts can wear and become damaged with regular use. Today's parts can even continue to function long past when they should, so it may not be apparent that a clutch assembly needs to be replaced until the entire unit is bad. If the engine is not performing as it should or if the drive shaft seems unstable, it may be time to replace the clutch assembly. This genuine OEM part includes everything needed for the job. This OEM clutch replacement is designed for use with various cultivators, edgers, and trimmers. It can be used on machines from MTD, RYOBI, Troy-Bilt, Bolens, Yard-Man, Cub Cadet, Murray, and Husky. This assembly includes the clutch, clutch drum, washer, and left-hand threaded screw. Always disengage the spark plug and allow the engine to cool completely before beginning repairs.

Flywheel assembly for gas leaf blowers and line trimmers. Mounts to the engine crankshaft. Replace if cracked, damaged, or missing flywheel fins.

Ignition module assembly for gas line trimmers. Replaces cracked, damaged, or malfunctioning ignition control modules. Essential component for engine operation.

Trimmer won't start or clutch exposed to debris? This clutch cover assembly shields the clutch from damage and keeps your trimmer running smoothly.

Muffler assembly for gas line trimmers. Installs on the exhaust to reduce engine noise. Replace if cracked, rusted, damaged, or excessively loud.

Replacement muffler screw that secures the muffler cover in place on lawn equipment. Needed when original screw is stripped, missing, or damaged.

Replace a cracked or seized engine block in your gas line trimmer with this short block assembly. Includes engine block and piston housing components.

Oil fill plug for gas line trimmers. Seals the oil reservoir to prevent leaks and spills. Replace if cracked, broken, stripped, or missing threads.

Oil fill tube assembly with dipstick for gas line trimmers. Replaces cracked, broken, or missing oil fill tubes that prevent proper oil level checks.

Engine won't start or runs rough? This spark plug provides reliable ignition for small engines in trimmers, blowers, and tillers. Easy DIY replacement.

If your electric start won't engage or spins freely, the chuck may be worn or damaged. This replacement chuck restores reliable starting functionality.

4-cycle engine oil for gas line trimmers and handheld equipment. Replace regularly per manufacturer schedule to ensure proper lubrication and engine performance. Verify compatibility with your model before ordering.

Restore reliable starting on your handheld equipment. This electric starter replaces worn or failed starting mechanisms. Moderate DIY repair.

Filters debris from engine intake air to protect internal components. Replace when clogged or engine runs rough. Verify fit with your trimmer model number.