Parts for Weedeater SB180: Engine Parts

Return spring for grass line trimmer throttle lever assembly. Restores proper lever operation when original spring is broken, stretched, or missing.

Cylinder shield for gas leaf blowers and line trimmers. Protects internal engine components. Replace if cracked, broken, or missing for proper operation.

If your chainsaw won't start or stop properly, the on/off switch may have failed. This safety switch controls power to the engine. DIY repair.

Replacement screw for grass line trimmers and outdoor power equipment. Secures housing components and assemblies. Order when original is stripped or missing.

Seals the fuel tank with an airtight fit to prevent spills during operation. Replace if cracked, loose, or leaking. Verify fit with your model number.

Fuel pickup filter draws gas from tank to carburetor. Replace if engine won't start or runs poorly due to clogged filter. Verify fit with your model number.

Fix hard starting or rough running trimmers with this spark plug. Common fix for no-start conditions. Easy 5-minute replacement for most models.

Cylinder gasket with adhesive for grass line trimmers, hedge trimmers, and leaf blowers. Replace when worn or damaged to prevent air leaks and maintain engine compression. Verify fit with your model number before ordering.

Fix a loose or rattling piston with this wrist pin retainer. Secures the piston pin in trimmers, blowers, and hedge trimmers. Basic hand tools needed.

If your carburetor is loose or vibrating excessively, this mounting screw secures it to the engine assembly. Quick 5-minute fix for most models.

Wave washer for lawn and garden equipment. Replace when worn or damaged to maintain proper tension and spacing. Verify fit with your model number.

Choke spacer for grass line trimmers and other outdoor power equipment. Replaces cracked, broken, or missing spacers in the carburetor choke assembly.

Tapping screw for outdoor power equipment engines. Replaces missing, stripped, or damaged mounting screws. Consult your parts diagram for location.

Carburetor assembly kit mixes air and fuel for your chainsaw, trimmer, or blower engine. Replace when engine runs rough, stalls, or won't start. Verify fit with your model number.

Seals the carburetor to prevent debris contamination in your trimmer or blower. Replace if you notice fuel leaks or engine performance issues.

Foam seal for leaf blowers that prevents air leaks in engine compartment. Replace when worn, cracked, or damaged to maintain proper performance. Verify fit.

Replacement mounting screw for grass trimmers, hedge trimmers, blowers, and pruners. Secures housings and covers. Replace if stripped, missing, or damaged.

If your trimmer won't start or runs rough, a damaged reed valve may be blocking proper fuel-air flow. This inlet valve ensures one-way crankcase flow.

Replacement mounting screw for chainsaws and outdoor power equipment. Secures components in place. Replace if stripped, missing, or damaged during maintenance.

Engine won't start or runs rough? This leaf blower crankshaft assembly converts linear motion to rotational motion. Essential engine component.

Engine won't start or has weak power? A sheared flywheel key disrupts timing. This small metal key aligns the flywheel to the crankshaft. Easy 15-minute fix.

Engine won't start or rope pulls out completely? This starter rope kit wraps around the recoil pulley to engage the engine. Simple DIY fix, 3 feet long.

Crankshaft seal prevents oil leaks and maintains engine pressure in grass trimmers. Replace when you notice oil seepage or starting difficulties. Verify fit with your model number before ordering.

This is a carburetor rebuilt kit made for use with gas powered chainsaws. It comes with many parts, including gaskets and diaphragms, that can get a chainsaw running properly again if there are issues with the carburetor. The carburetor is an important component of the chainsaw that ensures the right amount of gas and air reach the cylinder to ignite. The main symptom of carburetor issues is an engine that won't start even when the tank is full of fuel.There's a simple test to determine if the carburetor has an issue inside the chainsaw. The air filter will need to be removed from the equipment before a small amount of fuel is added directly to the carburetor. If the carburetor has problems, the engine will start for a short time before shutting off. Replacing or repairing the carburetor will be required.This carburetor rebuild kit is a genuine OEM replacement part that is directly sourced from the manufacturer. It is sold as an individual kit with several components. The kit is made for use with chainsaws manufactured by Zama and Stihl.

Replacement mounting screw for brush cutters, chainsaws, trimmers, and blowers. Replaces lost, stripped, or broken screws during repairs or maintenance.

String trimmer won't start or recoil pulls but won't engage? This recoil starter retainer secures the pulley assembly. Quick 10-minute replacement.

Fix a leaf blower that won't start or has a stuck pull cord with this recoil starter pulley. Essential component of the pull-start mechanism.

Starter rope won't retract? This recoil spring tensions the starter pulley to retract the pull cord. Durable metal construction. DIY-friendly repair.

Replace a broken or cracked starter handle that won't recoil or pull smoothly. This handle restores easy pull-starting on your trimmer in minutes.

If your chainsaw won't start or runs then stalls, a cracked fuel line may be blocking fuel flow. This replacement line restores proper fuel delivery.