Parts for Briggs & Stratton 445877-0502-E1: Engine Sump, Gasket Set-Engine, Lubrication Parts

Prevents oil leaks around the crankshaft in small gas engines. Replace if oil seeps from the bottom of the engine. Verify fit with your model number.

Fixes oil leaks, coolant mixing, or overheating issues. Creates seal between cylinder head and engine block. Clean surfaces before installing.

Fix oil leaks or perform routine oil changes with this engine oil drain plug. Threads into the oil tank base for secure drainage. Simple DIY repair.

Fix oil leaks and overheating with this engine oil seal. Creates a tight seal around the crankshaft to protect oil flow. Basic hand tools needed.

Replacement mounting screw for lawn and garden engines. Secures engine components and panels. Order a new screw if yours is stripped, missing, or damaged.

This O-ring seal is used in all sorts of lawn and garden equipment as a seal for the oil dipstick. It helps seal the system from debris and dirt that could otherwise reach the oil and end up in the motor. Over time, an O-ring will start to shrink, which c

This replacement valve seal is a genuine OEM part for a lawn tractor or mower. The valve stem is a type of valve that transfers oil into the cylinder and then immediately reseals due to the pressure in the chamber. However, if the seal is damaged, it will not close and oil will leak into the cylinder. If this happens, the cylinder head may become overly lubricated and not run well. This seal helps prevent that from happening. It fastens to the intake valve and valve stem keeper. Seals will naturally wear out over time due to stress and exposure to corrosive oxidizing agents in an engine. When this happens, the valve will leak oil. To test if the valve seal is compromised, look for whitish-grey smoke that indicates burning oil and also measure to see how much oil the engine is consuming. If the seal is breached, use a screwdriver and socket wrench set to change out the part. This top of the line replacement valve seal is compatible with Briggs & Stratton, Toro, and Lawn Boy lawn tractors. It is sourced from the original manufacturer and ships individually.

This replacement exhaust gasket is a certified genuine OEM part for a lawn tractor engine. This gasket helps to seal off the exhaust from the carburetor. For an engine to run, it must first mix fuel with air to prepare the fuel for combustion. By sealing off the exhaust, this gasket allows for fresh air to enter into the carburetor from outside the engine rather than from the exhaust. Gaskets often degrade over time due to the stress of pressure and heat. If the exhaust gasket breaks its seal, it can affect the engine's overall performance. Be on the lookout for an especially noisy engine that doesn't provide as much power and is less fuel efficient. There may also be a noticeable burning smell coming from the engine. To replace the exhaust gasket, use a socket wrench and wrench set to remove the air filter and blower housings, then remove the exhaust manifold and switch out the gasket. This replacement exhaust gasket is compatible with engines made by Toro, Briggs & Stratton, Murray, Snapper, and Simplicity. It comes sourced directly from its original manufacturer and does not include any additional hardware.

This oil pump cover is a genuine Midwest Engine part, sold individually. This oil pump cover can be used as a replacement part for lawnmowers, snowblowers, wood chippers, and lawn tractors. It ensures that the oil pump can deliver oil to the engine without any excessive oil leakage. Symptoms of a damaged oil pump cover can include oil leakage in and around the cover, reduced oil pressure, and oil leakage in and around the intake manifold gasket. If any of these symptoms occur and are directly attributable to the oil pump cover, the part should be immediately replaced with this genuine OEM replacement part. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This is an OEM part sourced directly from the manufacturer, and it is sold individually. This Oil pump cover is compatible with the following outdoor appliance brands: Midwest Engine, Briggs & Stratton, Toro, Simplicity, Cub Cadet, Lawn-Boy, and MTD.

Seals the cylinder head to prevent oil leaks on small engines. Replace when oil consumption increases or leaks develop. Verify fit with your model number.

Oil filter for Intek and Vanguard engines. Replace at season start or every 50 hours to protect engine from contamination. Confirm fit with your model.