Parts for Jenn-Air GO206B-8: 03 - Escutcheon Assembly Parts

Replacement control knob that restores reliable control of your appliance's settings and provides a secure grip for changing cycles or temperatures for fast, simple repairs. What it does:

• Fits over the appliance control shaft so you can turn settings, cycles, or temperatures; replace if the knob spins freely or won't engage the control.
• Restores clear position indexing and tactile feedback; replace when the knob is cracked, broken, or the indicator no longer lines up.
• Keeps the control firmly in place during use; replace if the knob slips or won't stay seated on the shaft.

• Always disconnect power (and gas for gas appliances) before servicing controls.
• Remove the old knob by pulling straight off the control shaft; inspect the shaft for damage or debris before installing the new knob.
• Align the knob with the shaft flats/splines and press on until fully seated—do not force.
• If the knob does not seat correctly, double-check shaft type and orientation; stop.

The Oven Door Hinge is an OEM part for Whirlpool wall ovens and ranges. Located on both sides of the oven door frame, these metal hinges provide the pivoting connection that allows smooth opening and closing of the door during cooking cycles.

Causes of failure can include wear of the hinge joints from repeatedly bearing the weight of the heavy oven door over thousands of uses. Exposure to high heat during cooking may gradually deteriorate lubricating grease or materials.

Symptoms of faulty hinges include:

• Door rubbing or sticking during opening/closing
• Off-center alignment when shut or inability to fully latch
• Noisy squeaking or grinding emerging from hinges
• Hinges loosened from screws/fastenings or mechanisms seized

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.

• Fastens panels, brackets, covers, or internal parts to the chassis or frame
• Helps maintain alignment and support, reducing rattle, vibration, or looseness
• Replaces missing or damaged screws that have backed out, broken, or stripped
• Restores secure mounting after service when original hardware is lost

• Disconnect power; shut off water or gas supplies before servicing
• Use the correct driver; start threads by hand to avoid cross-threading
• Match length and thread to the original location; do not substitute with longer hardware
• Tighten snugly; do not overtighten into plastic or thin metal

Size: 8-32 x 1/4 inch.

This is a genuine lock nut replacement. This is a general piece of hardware that is often used on several types of lawn and garden equipment, including in engines, housing, and other areas. The exact application of this part will vary based on the unit. The lock nut is used to create a more secure seal than a standard nut. When properly secured, the lock nut tightens to a bolt and uses an extra locking washer with teeth to ensure a snug fit.If lock washers do get damaged or lost, they need to be replaced immediately with a genuine OEM replacement. This model is compatible with all types of machines and units since it is a generic part. The washer is sold as an individual part and manufactured by Whirlpool. Lock nuts will need to be installed using a socket wrench or adjustable wrench. Pliers, a screwdriver, or another socket wrench will be needed to hold the bolt while the lock nut is being secured in place. Be sure to thread the lock nut carefully to ensure a strong seal and avoid stripping the bolt or the nut.

Controls heat to a range's cooktop element. This infinite switch restores smooth, precise temperature control when a surface burner won't heat, only stays on high, or won't shut off.

• Regulates electrical power to the surface element for adjustable heat levels
• Provides a true OFF position to shut the burner down
• Common symptoms of a failed switch: no heat, stuck on high, or won't turn off
• Installs in the control panel and connects to the existing surface element circuit

• Disconnect power at the breaker before servicing
• Access the switch from the rear of the control panel; remove the knob and mounting hardware
• Transfer wires one at a time to matching terminals (or photograph the layout) to keep connections correct
• Reassemble, restore power, and test the burner through all settings

This part has been discontinued by the manufacturer and is no longer available.