Parts for Hot Point HCM9CTBCD: Freezer Parts

This freezer door hinge is a direct-fit replacement that supports and pivots the freezer door for proper alignment and smooth opening. Restores secure door movement and helps maintain an even door seal. What it does:

• Supports the freezer door and provides the pivot point for opening and closing
• Keeps the door aligned to prevent sagging and rubbing on the cabinet
• Helps maintain an even seal to reduce cool-air loss from the freezer
• Common symptoms it fixes: door sag, uneven closing, noisy or stiff hinge movement

• Designed to replace the original hinge; compare part visually before ordering
• Installation typically requires removing the door and fastening hinge hardware; follow manufacturer instructions
• Keep power off and remove food from door area if removing the door
• Inspect hinge screws and mounting surfaces; replace damaged hardware as needed

This exterior drain plug seals the washer's drain opening to prevent leaks and contain water in the tub during operation. It provides a simple replacement to restore a watertight seal at the appliance drain area. What it does:

• Seals the drain opening to help prevent water leaks from the tub or drain housing
• Helps maintain proper drainage by keeping debris out of the drain path
• Can stop visible water weeping or puddling near the base of the washer
• Replaces a cracked, worn or missing exterior drain plug to restore normal operation

• One exterior drain plug

• Disconnect power to the appliance and turn off water supply before starting any work
• Remove the appropriate access panel or lower kick plate to reach the drain opening
• Press or thread the plug into the drain opening as designed; snug by hand and avoid over-tightening
• Inspect the surrounding seal area and replace any damaged gaskets or housings if present; test for leaks after reinstalling panels and restoring power/water

The Drier is an OEM component specifically designed for GE combination refrigerator-freezers. Absorbing moisture, its treated silica particles buffer humidity within refrigerant lines. Proper drying sustains energy-efficient performance while preventing corrosion.

Causes of a faulty drier commonly relate to saturation reducing capacity. As desiccant degrades, water passes into closed system compressors requiring change. 

Symptoms of a bad drier involve:

• Frost and ice buildup impairing cooling  
• Puddling around evaporator evidencing leaks
• Higher operating costs from impaired efficiency

Causes of a bad drier involve typical saturation shortening drying cycles. Cracks release desiccant particles risking blockages necessitating timely replacement.

This OEM GE part is also compatible with some Hotpoint, RCA, and Frigidaire combination units. Replace to retain steady humidity management protecting components and maximizing freshness years of operation.
 

This compressor harness routes electrical power and signal connections to the refrigerator compressor, restoring reliable electrical connection for proper compressor operation and helping address compressor-related electrical faults. What it does:

• Provides the factory-style electrical connection between the compressor and the appliance wiring
• Carries start/run signals and power to the compressor motor
• Replaces damaged, corroded, or frayed compressor wiring to help stop intermittent operation, clicking, or failure to start
• Helps prevent shorting or arcing caused by compromised harness insulation or terminals

• One compressor harness as shown

• Disconnect power to the appliance before starting any repair
• Match connector types and terminal positions before removing the old harness
• Replace only with the harness that fits the compressor and route wires clear of sharp edges or heat sources
• If terminals are corroded or the compressor shows other faults, inspect related components as needed

The R600 Process Valve with Red Cap is an OEM part for GE refrigerators. It regulates the flow of refrigerant within the cooling system, ensuring proper cooling and temperature control.

A bad process valve can occur due to wear and tear, refrigerant leaks, or mechanical failure. If you notice symptoms such as inadequate cooling, excessive frost buildup, or unusual noises coming from the refrigerator, it may indicate a faulty or malfunctioning process valve.

Symptoms of a bad process valve include:

• Inadequate cooling or inconsistent temperature control
• Excessive frost buildup in the freezer
• Unusual noises coming from the refrigerator

Restore your refrigerator by replacing the faulty process valve with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.