Parts for Ge PSB48YSXASS: 01 - Freezer Door Parts

Replace your refrigerator water filter every 6 months to maintain clean water and ice. Removes contaminants for fresh taste. Easy DIY install in minutes.

Outer door panel assembly for refrigerator freezer compartment. Replaces damaged, dented, or discolored exterior panels. Stainless steel finish.

Fix a refrigerator that won't turn on or has door light issues with this microswitch. Common repair for failed switches. Moderate DIY difficulty.

Water line cap tube for refrigerators. Connects water supply lines in the refrigeration system. Replace if cracked, leaking, or damaged during repairs.

Water line cap tube for refrigerators. Connects water supply lines in the refrigeration system. Replace if cracked, leaking, or damaged during repairs.

If your refrigerator interior light won't turn on or flickers, a faulty light socket is often the cause. This replacement socket restores reliable lighting.

Replace your refrigerator's ice dispenser door chute funnel if cracked, broken, or missing. This component directs ice from dispenser to glass.

Illuminates water and ice dispenser area for visibility in low light. Replace when bulb burns out or dispenser area stays dark. Confirm fit with model.

This strike switch is a door-latch sensing switch that completes the circuit when the door is closed, ensuring the appliance detects latch position and enables associated functions. It replaces a worn or failed switch to restore proper door sensing. What it does

• Detects when the door latch/strike engages and sends the on/off signal to the appliance control
• Prevents functions that require a closed door from running when the door is open
• Commonly fails from wear or corrosion on contacts or broken actuator
• Symptoms of failure: appliance functions not starting, interior light or controls not responding, or door-dependent features not operating

• One strike switch

• Disconnect power to the appliance before starting work to avoid shock
• Access typically requires removing a door panel or control housing; retain all fasteners and note wire locations
• Disconnect wiring harness and replace with same-terminal connections; do not force connectors
• Test door operation and related functions after reassembly

Door stop assembly that secures and positions your refrigerator door. Replace if the original is cracked, broken, or missing to restore proper door alignment.

Seals freezer door to maintain temperature and prevent frost buildup. Replace if torn, cracked, or door doesn't seal properly. Verify fit with model number.

Replace a worn or missing hinge shim on your refrigerator door. This small spacing component ensures proper door alignment and clearance at the hinge.

If your refrigerator's water or ice dispenser looks damaged or has cracked trim, this dispenser trim piece restores the professional appearance. Easy install.

Fixes inconsistent cooling or frost buildup caused by faulty temperature sensing. This refrigerator defrost thermostat restores accurate readings.

Replace your refrigerator's drip pan grille recess if the original is cracked, broken, or missing. Installs at the base to cover the drain trough.

Black dispenser drip tray for your refrigerator. Catches water and ice spills below the dispenser. Replace if cracked, broken, or missing.

A small locking retainer that secures push-fit fittings and tubing to prevent disconnection and leaks. Replaces a worn or broken clip to restore a secure connection on the water/ice plumbing assembly. What it does:

• Holds push-fit or slip fittings firmly in place to stop tubing from slipping free
• Helps prevent water leaks caused by loose or damaged retainers
• Restores proper alignment of the inlet/outlet plumbing connections
• Commonly used where a quick-release fitting needs a secondary lock

• One clip fitting lock

• Disconnect power and turn off the water supply before servicing plumbing components
• Remove the old clip and push the new clip into place until the fitting is fully retained
• After installation, restore water and power and check the connection for leaks

Replacement door handle bar for refrigerator. Installs on the door exterior. Needed when original handle is cracked, broken, or missing.

Upper thimble hinge secures the refrigerator door pivot point for smooth opening and closing. Replaces cracked, broken, or worn hinge parts that cause door misalignment or sagging.

Replace your refrigerator's nameplate if the original is cracked, faded, peeling, or missing. This cosmetic faceplate restores the model identification.

A self-tapping screw used to fasten appliance components where a threaded hole is not present. It provides a secure connection for panels, brackets, or internal assemblies to restore proper fit and reduce movement. What it does:

• Cuts its own mating thread as it is driven, securing plastic or thin metal components
• Holds panels, brackets, or assemblies in place to prevent rattling and misalignment
• Restores proper attachment when original screw is stripped, missing, or damaged
• Helps maintain electrical and mechanical component positioning for safe operation

• Use the correctly sized screwdriver or driver bit to avoid cam-out or head damage
• Drive straight and avoid over-torquing to prevent cracking or stripping the mating material
• If working near electrical components, disconnect power before servicing
• Replace like-for-like with the same part number to ensure proper fit and function