Parts for Ge ZIS360NRF: 01 - Freezer Door Parts

The water filter is an OEM part for GE refrigerators. This filter removes or reduces various contaminants.

Features and Benefits:

• Easy DIY replacement, typically mounted inside the refrigerator at the back of the compartment.
• Removes or reduces various contaminants in your water and ice, including lead, cysts, asbestos, atrazine, , taste and odor, chlorine, sediment, turbidity, and more
• NSF/ANSI 42 and 53 standards
• 6 Month lifespan filter
• Carbon Block media
• Micron rating: 0.5-1 micron (Class I)

When to replace your filter:

• Bad taste or odor in water and ice
• Cloudy or discolored ice
• Reduced water flow or pressure
• Refrigerator replace filter indicator light is on

Note: If replacing the Culligan metal canister design filter for the first time, a special adapter, part number AP2615702 is needed, which is not included with this part. The compatible bypass cap is part number AP6891551.

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

This hardware pack provides the assorted fasteners needed to secure trim, panels, and small appliance components, helping replace missing or damaged screws and clips for a clean, stable fit. What it does

• Replaces lost or damaged screws, clips and small fasteners used on appliance trim and panels
• Helps stop rattling or loose panels by restoring proper fastening
• Secures small components during reassembly after maintenance or part replacement
• Useful when original mounting hardware is missing or corroded

• Disconnect power to the appliance before servicing to reduce shock risk
• Use the correct screwdriver or driver bit to avoid stripping fasteners
• Keep small parts away from children and pets; work on a covered surface to catch dropped pieces

This bottom freezer door hinge secures and guides the freezer door at the lower pivot, restoring proper door alignment and sealing for consistent cooling. Designed to replace a worn, bent or broken lower hinge. What it does:

• Provides a stable pivot point so the freezer door opens and closes smoothly
• Helps maintain an even door gap to improve seal and reduce cold air loss
• Prevents sagging or misalignment that can cause rubbing or difficulty latching
• Fits the lower/bottom position on compatible freezer doors

• Inspect hinge mounting holes and fasteners; replace any damaged screws or clips
• Support the door during removal/installation to avoid strain or injury
• Tighten fasteners snugly but avoid over-torquing to prevent damage
• If door continues to sag after replacement, check upper hinge and door gasket condition

This replacement freezer bottom hinge bushing helps the freezer door pivot smoothly and maintain proper alignment, reducing rubbing and uneven wear for more reliable closing. What it does:

• Provides a smooth pivot surface for the freezer bottom hinge
• Restores proper door alignment to help ensure a tight seal
• Reduces hinge noise, sticking, and rubbing during door movement
• Helps prevent premature wear of the hinge and door components

• One freezer bottom hinge bushing

• Disconnect power to the appliance and empty or support the door before starting
• Support the door while removing hinge fasteners to prevent falling or injury
• Inspect the hinge and shaft for wear; replace the hinge assembly if damaged
• Do not overtighten fasteners; test door operation after installation

This is the magnetic door gasket that seals the refrigerator compartment. A tight, intact gasket helps maintain proper temperature and reduces energy loss by keeping warm air out and cold air in.

• Creates an airtight seal between the refrigerator door and cabinet
• Helps prevent temperature swings, frost, and moisture around the door
• Worn, torn, or warped gaskets can cause warm spots, condensation, or doors not closing properly
• Replace if you see cracks, gaps, or if the gasket no longer holds a seal

• Unplug the appliance before service and remove door contents for easier handling
• Gently warm the gasket (hair dryer on low) to relax folds and improve fit
• Transfer and reuse any retaining hardware; seat the gasket fully in the channel
• Check door alignment and perform a dollar-bill test around the perimeter to confirm sealing

Restore secure, organized door storage with this door bin assembly. It replaces a cracked or missing bin so bottles, jars, and condiments stay in place, easy to reach, and less likely to tip or spill.

• Creates a sturdy shelf on the door to hold jars, bottles, and condiments
• Common symptoms: cracked plastic, broken/loose mounting tabs, bin falls off or won't stay seated, missing bin
• Restores original door storage capacity and organization
• "36/42" denotes the manufacturer's designated bin style for those series; confirm fit by model

• Remove items from the old bin; lift the bin straight up to release from the door rails
• Allow cold plastic to warm to room temperature before handling to reduce cracking risk
• Align new bin on the molded door ribs/rails and press down until fully seated
• Verify a secure fit before reloading; avoid overloading the bin

This refrigerator freezer bottom door trim restores the finished lower edge of the freezer door, improving appearance and sealing against drafts. It replaces damaged or cracked trim to help keep the freezer looking and functioning properly. What it does:

• Covers and protects the lower exterior edge of the freezer door from chips, dents, and wear
• Helps maintain a tidy seal line where the door meets the cabinet, reducing visible gaps
• Restores the original finished appearance after impact or aging damage
• Matches the OEM shape so the door closes and aligns correctly

• One freezer bottom door trim piece

• Designed to install with existing factory fasteners; inspect clips and screws and replace if damaged
• Remove power to the appliance and work with the door in a stable, supported position
• Use trim-safe tools to pry or align the piece to avoid scratching the finish
• If metal mounting clips are bent or broken, source replacements before installing this trim

This pack contains twelve replacement screws used to fasten appliance panels, trim, and components. They restore secure mounting and help stop rattling, loose panels, and gaps for a safer, quieter appliance. What it does:

• Secures exterior and interior panels, brackets, and trim pieces
• Restores proper fit where missing or stripped screws cause movement or noise
• Helps maintain appliance alignment and prevents parts from vibrating loose
• Used for general-purpose repairs on compatible GE appliances

• Disconnect power or unplug the appliance before performing any internal repairs
• Use the correct screwdriver bit and avoid overtightening to prevent stripping threads
• Keep remaining screws in a labeled container for future service
• If a screw does not seat easily, stop and verify correct fit to avoid damage

Replacement screw that secures panels and internal components, helping stop rattles and keep parts aligned. Use it to replace stripped, rusted, or missing fasteners and restore a secure fit. What it does:

• Secures panels, trim, or internal parts to prevent movement and vibration.
• Replaces worn, corroded, or missing screws that cause loose panels or rattling.
• Restores proper alignment for doors, covers, and mounted components.
• Provides a simple hardware fix that helps maintain safe, stable operation.

• Always disconnect power to the appliance before accessing internal components.
• Use the correct screwdriver or bit to avoid stripping the head; apply firm but controlled torque.
• Verify screw length, head style, and thread type match the original before installation.
• If threads are damaged, replace with a matching OEM screw rather than over-tightening.

This handle trim cover replaces a worn or damaged door handle end cap to restore a clean, finished look and hide fasteners. It snaps or slides into place on the door handle for a neat appearance. What it does:

• Covers the exposed end of a refrigerator/freezer door handle for a finished appearance
• Hides screws and fasteners to improve aesthetics
• Helps keep dirt and moisture out of the handle cavity
• Suitable when trim is cracked, scratched, faded, or missing

• 1 handle trim cover

• Remove the existing trim or handle before installing
• Align trim with handle end and press or slide into place until it seats securely
• Use basic hand tools; avoid forcing parts to prevent damage
• Disconnect power or follow appliance safety guidance before servicing if applicable