Parts for Ge GFE26JEMAFDS: Freezer Door Parts

The GE XWFE Refrigeration Water Filter is an OEM part for GE refrigerators. This advanced water filter is designed to reduce a wide range of contaminants, including chlorine, lead, cysts, and select pharmaceuticals, providing clean and safe drinking water and ice. It seamlessly integrates into the refrigerator's filtration system, ensuring optimal water quality.

You should replace this water filter if it becomes clogged or reaches the end of its lifespan, typically every six months. Common causes of a bad water filter include excessive contaminants, improper installation, or failure to follow the replacement schedule.

Symptoms of a bad water filter include:

• Reduced water flow from the dispenser
• Unpleasant taste or odor in water and ice
• Cloudy or discolored water
• The filter indicator light on the refrigerator signaling a replacement

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This freezer door gasket forms an airtight seal between the freezer door and cabinet. Replacing a worn seal helps keep cold air in, reduce frost and condensation, and support consistent freezer temperatures.

• Seals the door perimeter to prevent warm air leaks
• Helps maintain stable internal temperature and humidity
• Reduces frost/ice buildup and moisture around the opening
• Common symptoms of failure: torn or warped gasket, poor door seal, frost along edges, temperature fluctuations

• Unplug the refrigerator before starting; open the freezer door
• Warm the new gasket with warm water or a hair dryer on low to relax it for easier installation
• Seat the corners first, then press the gasket evenly into the channel/retainer and ensure uniform contact around the perimeter
• Perform a paper-slip test and allow the gasket to conform after closing the door for several hours

This bracket support is a small mounting bracket that secures and stabilizes appliance components, helping keep panels and assemblies aligned for proper operation and reduced vibration. It's a direct-fit replacement when the original bracket is broken or missing. What it does

• Provides a sturdy mounting point to hold panels or internal components in place
• Restores proper alignment to doors, panels or assemblies that sit on the bracket
• Reduces rattling or vibration caused by a loose or damaged bracket
• Helps prevent wear or damage from parts shifting during use

• Unplug the appliance and shut off water/gas (if applicable) before starting work
• Use the original mounting screws; replace damaged fasteners as needed
• Handle sharp sheet-metal edges carefully and wear gloves and eye protection

This is a 1/4-20 UNC machine screw used to fasten appliance components securely. It restores proper fit and stability where threaded fasteners are required, preventing loose panels or shifting parts. What it does:

• Secures panels, brackets, or assemblies that use a 1/4-20 UNC threaded hole
• Stops rattling or movement caused by a missing or damaged screw
• Restores correct mechanical connection for safe operation
• Useful when replacing stripped, corroded, or lost fasteners

• Disconnect power to the appliance before servicing.
• Start threads by hand to avoid cross-threading; tighten until snug.
• Do not overtighten — use appropriate torque for the material to avoid stripping threads or damaging parts.
• Ensure proper contact and secure fastening.

This replacement screw secures appliance brackets, panels, and components. It restores a tight, aligned fit when the original hardware is stripped, rusted, or missing, helping reduce vibration and rattling for reliable operation.

• Fastens brackets, panels, or mounts to keep components secure and aligned
• Replaces missing, stripped, or corroded hardware
• Helps reduce vibration, rattling, or loose/misaligned parts
• Matches original spec for reliable hold and fit

• Disconnect power before servicing; use proper PPE
• Match thread and length to the removed screw before installation
• Start threads by hand to prevent cross-threading; tighten until snug—do not overtighten
• Ensure parts are aligned and seating surfaces are clean before tightening

This drawer bracket secures and supports a refrigerator drawer, restoring proper alignment and smooth operation. Replace a broken or cracked bracket to prevent sagging drawers and ensure contents slide correctly. What it does:

• Supports the drawer assembly and keeps the drawer level during opening and closing
• Restores proper drawer alignment when original bracket is cracked or damaged
• Prevents drawer sagging or binding that can catch or stick
• Helps maintain smooth sliding and proper engagement with the drawer track

• One drawer bracket

• Designed for direct replacement; remove drawer and any trim to access mounting location
• Compare the part to the original before installation to confirm orientation and screw hole alignment
• Use appropriate hand tools; do not force the bracket to avoid cracking adjacent plastic parts
• Disconnect power only if accessing components where electrical parts could be disturbed

This drawer bracket secures and supports a refrigerator drawer, keeping it aligned and stable for smooth opening and closing. A direct-fit replacement that restores proper drawer function and prevents sagging or misalignment. What it does:

• Supports and stabilizes the drawer to maintain proper alignment
• Keeps the drawer track engaged for smooth sliding action
• Prevents the drawer from sagging or detaching when loaded
• Helps stop rattling or uneven movement caused by a damaged bracket

• Disconnect power to the appliance before beginning any repair
• Remove drawer contents and slide out the drawer to access the bracket area
• Inspect mounting points and hardware; replace any worn screws or clips as needed
• Tighten fasteners securely but avoid over-torquing to prevent damage

The Fastener Handle Assembly is an OEM part for GE refrigerators, specifically designed to securely attach the refrigerator or freezer handle to the door. This assembly includes the necessary components, such as screws or bolts, brackets, and possibly end caps, depending on the design, to ensure a sturdy and durable connection between the handle and the door. 

Causes for a Fastener Handle Assembly to fail include normal wear and tear from repeated use, excessive force applied to the handle, or corrosion of metal parts due to moisture and refrigeration environment.  

Symptoms of a bad Fastener Handle Assembly include:

• A loose handle that moves or wobbles when touched or used.
• Difficulty in opening the refrigerator or freezer door due to a compromised handle attachment.
• Visible damage or wear to the components of the fastener assembly 

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 

The Handle is an OEM part for GE refrigerators. It allows for easy opening and closing of the door. This handle is designed to provide a sturdy grip, making it convenient to access your food items.

A bad handle can be caused by wear and tear over time, excessive force applied to the handle, or damage due to accidental impact or mishandling.

Symptoms of a bad drawer handle include:

• Difficulty in opening or closing the door.
• Loose or wobbly handle.
• Cracks or breaks in the handle.

Replace your worn-out or damaged handle with this OEM part and restore your refrigerator. This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.