Parts for Ge GFE26JYMWFFS: Freezer Door Parts

This freezer door gasket forms an airtight seal between the freezer door and cabinet. Replacing a worn seal helps keep cold air in, reduce frost and condensation, and support consistent freezer temperatures.

• Seals the door perimeter to prevent warm air leaks
• Helps maintain stable internal temperature and humidity
• Reduces frost/ice buildup and moisture around the opening
• Common symptoms of failure: torn or warped gasket, poor door seal, frost along edges, temperature fluctuations

• Unplug the refrigerator before starting; open the freezer door
• Warm the new gasket with warm water or a hair dryer on low to relax it for easier installation
• Seat the corners first, then press the gasket evenly into the channel/retainer and ensure uniform contact around the perimeter
• Perform a paper-slip test and allow the gasket to conform after closing the door for several hours

This bracket support is a small mounting bracket that secures and stabilizes appliance components, helping keep panels and assemblies aligned for proper operation and reduced vibration. It's a direct-fit replacement when the original bracket is broken or missing. What it does

• Provides a sturdy mounting point to hold panels or internal components in place
• Restores proper alignment to doors, panels or assemblies that sit on the bracket
• Reduces rattling or vibration caused by a loose or damaged bracket
• Helps prevent wear or damage from parts shifting during use

• Unplug the appliance and shut off water/gas (if applicable) before starting work
• Use the original mounting screws; replace damaged fasteners as needed
• Handle sharp sheet-metal edges carefully and wear gloves and eye protection

This is a 1/4-20 UNC machine screw used to fasten appliance components securely. It restores proper fit and stability where threaded fasteners are required, preventing loose panels or shifting parts. What it does:

• Secures panels, brackets, or assemblies that use a 1/4-20 UNC threaded hole
• Stops rattling or movement caused by a missing or damaged screw
• Restores correct mechanical connection for safe operation
• Useful when replacing stripped, corroded, or lost fasteners

• Disconnect power to the appliance before servicing.
• Start threads by hand to avoid cross-threading; tighten until snug.
• Do not overtighten — use appropriate torque for the material to avoid stripping threads or damaging parts.
• Ensure proper contact and secure fastening.

This replacement screw secures appliance brackets, panels, and components. It restores a tight, aligned fit when the original hardware is stripped, rusted, or missing, helping reduce vibration and rattling for reliable operation.

• Fastens brackets, panels, or mounts to keep components secure and aligned
• Replaces missing, stripped, or corroded hardware
• Helps reduce vibration, rattling, or loose/misaligned parts
• Matches original spec for reliable hold and fit

• Disconnect power before servicing; use proper PPE
• Match thread and length to the removed screw before installation
• Start threads by hand to prevent cross-threading; tighten until snug—do not overtighten
• Ensure parts are aligned and seating surfaces are clean before tightening

This drawer bracket secures and supports a refrigerator drawer, restoring proper alignment and smooth operation. Replace a broken or cracked bracket to prevent sagging drawers and ensure contents slide correctly. What it does:

• Supports the drawer assembly and keeps the drawer level during opening and closing
• Restores proper drawer alignment when original bracket is cracked or damaged
• Prevents drawer sagging or binding that can catch or stick
• Helps maintain smooth sliding and proper engagement with the drawer track

• One drawer bracket

• Designed for direct replacement; remove drawer and any trim to access mounting location
• Compare the part to the original before installation to confirm orientation and screw hole alignment
• Use appropriate hand tools; do not force the bracket to avoid cracking adjacent plastic parts
• Disconnect power only if accessing components where electrical parts could be disturbed

This drawer bracket secures and supports a refrigerator drawer, keeping it aligned and stable for smooth opening and closing. A direct-fit replacement that restores proper drawer function and prevents sagging or misalignment. What it does:

• Supports and stabilizes the drawer to maintain proper alignment
• Keeps the drawer track engaged for smooth sliding action
• Prevents the drawer from sagging or detaching when loaded
• Helps stop rattling or uneven movement caused by a damaged bracket

• Disconnect power to the appliance before beginning any repair
• Remove drawer contents and slide out the drawer to access the bracket area
• Inspect mounting points and hardware; replace any worn screws or clips as needed
• Tighten fasteners securely but avoid over-torquing to prevent damage

The Fastener Door Handle is an OEM component for GE refrigerators. This door handle provides a comfortable grip for accessing refrigerator shelves and bins. It attaches securely to the refrigerator door through durable metal fasteners. 

Causes for a bad door handle could be cracks, damage, or stripped fastener holes resulting in a loose or detached handle. Regularly gripping and lifting may also cause normal wear over time.

Symptoms of a failing door handle include:

• The handle detaching completely from the door  
• Looseness making the handle wobbly or unstable to hold
• Sharp edges or broken parts posing a safety risk

This OEM GE handle is also compatible with Hotpoint, RCA, and select Kenmore refrigerator models.