Parts for Ge HCM9CWBCD: Freezer Parts

This freezer door hinge is a direct-fit replacement that supports and pivots the freezer door for proper alignment and smooth opening. Restores secure door movement and helps maintain an even door seal. What it does:

• Supports the freezer door and provides the pivot point for opening and closing
• Keeps the door aligned to prevent sagging and rubbing on the cabinet
• Helps maintain an even seal to reduce cool-air loss from the freezer
• Common symptoms it fixes: door sag, uneven closing, noisy or stiff hinge movement

• Designed to replace the original hinge; compare part visually before ordering
• Installation typically requires removing the door and fastening hinge hardware; follow manufacturer instructions
• Keep power off and remove food from door area if removing the door
• Inspect hinge screws and mounting surfaces; replace damaged hardware as needed

Storage basket for chest freezers. Hangs inside freezer compartment to organize smaller items. Replace if basket is cracked, bent, or missing.

This drain plug seals the tub drain opening to prevent water from leaking or pooling beneath the appliance. Replacing a damaged plug helps keep the tub watertight during fill and drain cycles. What it does:

• Seals the tub drain opening to stop leaks and water under the appliance.
• Commonly replaced when you see water pooling beneath the unit or a cracked/missing plug.
• Restores a watertight seal after tub or pump service.
• Small, simple part — inspect for cracks, splits, or hardening that cause leaks.

• Disconnect power and turn off the water supply before servicing the appliance.
• Drain any remaining water from the tub or pump to avoid spills when replacing the plug.
• Remove the old plug and install the new plug, ensuring it is fully seated and sealed; check for leaks after restoring power/water.

Green power indicator light shows your chest freezer is running. Replace if light fails to illuminate or stays dim. Confirm fit with your model number.

This sealed component removes moisture and contaminants from the R600 refrigerant system, typically located in the sealed system behind the refrigerator. Replace if the refrigerator isn't cooling properly, runs constantly, or if a technician identifies refrigerant system contamination.

This compressor harness routes electrical power and signal connections to the refrigerator compressor, restoring reliable electrical connection for proper compressor operation and helping address compressor-related electrical faults. What it does:

• Provides the factory-style electrical connection between the compressor and the appliance wiring
• Carries start/run signals and power to the compressor motor
• Replaces damaged, corroded, or frayed compressor wiring to help stop intermittent operation, clicking, or failure to start
• Helps prevent shorting or arcing caused by compromised harness insulation or terminals

• One compressor harness as shown

• Disconnect power to the appliance before starting any repair
• Match connector types and terminal positions before removing the old harness
• Replace only with the harness that fits the compressor and route wires clear of sharp edges or heat sources
• If terminals are corroded or the compressor shows other faults, inspect related components as needed

This is a self-tapping ST3.5 x 9.5 screw used to secure panels, trim and small appliance components. It replaces missing or damaged screws to restore proper fit and prevent rattling or loose parts. What it does:

• Fastens control panels, brackets, trim pieces and light assemblies
• Replaces stripped, corroded or missing screws that allow parts to shift
• Restores secure mounting and helps eliminate vibration noise
• Small size for low-profile applications where a compact fastener is required

• Use the correct sized Phillips or Pozidriv driver to avoid cam-out
• Start screws straight and drive until snug; avoid overtightening to prevent stripping
• Disconnect power and remove any sharp panels before working to stay safe
• Keep a small parts tray to avoid losing tiny screws during repair

A replacement harness door cover that protects and secures the wire harness at the appliance door, preventing chafing and moisture exposure for reliable electrical connections. What it does:

• Covers and organizes the door wiring harness to reduce rubbing and wear
• Helps keep wiring routed away from moving parts and sharp edges
• Protects harness from dirt and moisture near the door area
• Can resolve intermittent door-related electrical issues caused by damaged wiring

• One harness door cover

• Disconnect power to the appliance before starting any repair
• Install requires access to the door wiring area; panel removal may be necessary
• Handle carefully to avoid damaging adjacent wiring or connectors

Can't lock your freezer door or need child-safety access control? This door lock key engages the latch mechanism to secure the door and restrict access.

Fix cooling issues in your refrigerator with this process valve. Regulates refrigerant flow for proper temperature control. Red cap design for R600 systems.