Parts for Ge GTS18YBMARWW: 02 - Freezer Section Parts

Refrigerator plug button that installs in the cabinet or liner. Replace this insert if the original is cracked, broken, missing, or worn from use.

This ice maker receptacle cover protects the electrical connector and housing where the ice maker plugs into the refrigerator, helping keep the connection clean and secure for reliable ice maker operation. What it does

• Covers and shields the ice maker electrical receptacle from debris and moisture
• Helps prevent accidental contact with the connector for improved safety
• Maintains proper alignment and fit of the ice maker plug to reduce connector strain
• Commonly replaced when cracked, broken, or missing, which can expose the receptacle

• Disconnect power to the appliance before inspecting or replacing the cover
• Usually snaps or screws into place; remove adjacent trim or ice bin for access if needed
• Handle gently to avoid damaging surrounding plastic housings or the connector
• If electrical damage or corrosion is present, inspect wiring and connector; replace damaged parts before reassembly

A stainless steel hex-washer-head screw used to secure panels and components on compatible appliances. Corrosion-resistant construction helps maintain a secure fit where short, strong fasteners are required. What it does

• Fastens appliance panels, trim, or brackets where an 8-18 thread and short 3/8" length are specified
• Hex washer head provides a larger bearing surface to reduce pull-through
• Stainless finish resists rust in humid appliance areas
• Common replacement when original mounting screw is stripped, missing, or corroded

• One stainless steel hex-washer-head screw

• Use the correct 8-18 thread fastener and do not force mismatched screws to avoid thread damage
• Tighten securely but avoid overtightening to prevent stripped threads or cracked panels
• Power tools may be used with appropriate bit, but start by hand to ensure proper alignment
• If installing near electrical components, disconnect power before servicing

Secures and seals water line connections in your refrigerator's dispensing system. Replace if leaking or loose to prevent water damage. Confirm fit.

This plug housing switch is the molded connector that secures and protects the appliance power cord where it plugs into the appliance. It restores a stable, insulated connection and helps prevent arcing or intermittent power. What it does:

• Houses and secures the power cord terminals to maintain a reliable electrical connection
• Protects exposed terminals from moisture and debris to reduce shorting or arcing risk
• Replaces cracked, melted, or loose housings that can cause intermittent power or appliance failure
• Commonly used when the appliance won't power on or power is intermittent at the cord connection

• One plug housing switch

• Disconnect power at the breaker or unplug the appliance before servicing
• Inspect the power cord and terminal screws for damage; replace cord if terminals are burned or wires are compromised
• Hand tools typically required; ensure terminals are fully seated and screws tightened to secure the cord

Refrigerator not cooling but freezer works? A failed evaporator fan motor stops cold air circulation. DIY-friendly repair with basic tools in 30-60 minutes.

Freezer fan loud or not spinning? This evaporator fan blade circulates cold air over the coils. DIY-friendly repair with our video guide.

The Lid Bumper is an OEM part for GE refrigerators. It is designed to provide cushioning and protection for the refrigerator lid, preventing damage and ensuring smooth, quiet closing. 

Causes of a bad Lid Bumper can include deterioration over time due to frequent use, exposure to temperature variations, or damage from accidental impacts. A worn or damaged bumper may no longer provide adequate cushioning, leading to potential damage to the lid or the refrigerator itself.

Symptoms of a bad Lid Bumper include:

• The refrigerator lid closing too hard
• Unusual noises when closing the lid
• Visible wear or cracks on the bumper

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Rubber grommet cushions and stabilizes the evaporator fan motor in your refrigerator. Replace if cracked, worn, or missing to reduce vibrations and noise.

Fix a warm fridge or freezer ice buildup. This defrost heater melts frost on evaporator coils to restore cooling. Moderate DIY repair, 1-2 hours.

This replacement defrost heater warms the freezer's evaporator area during the automatic defrost cycle. It melts accumulated frost so air can circulate, helping maintain stable temperatures and preventing ice buildup on the back wall.

• Heats the evaporator to clear frost and ice during defrost
• Helps keep airflow passages and the defrost drain path open
• Common symptoms of a failed heater: heavy frost on the back panel/coils, poor cooling or warm sections, fan noise from ice contact, cooling returns temporarily after a manual defrost
• Typically located behind the rear freezer panel

• Disconnect power before servicing; wear cut-resistant gloves
• Access the evaporator by removing the freezer's rear panel; thaw heavy ice before removal
• Transfer any clips/brackets and route wires exactly as original, keeping them away from plastic parts
• After installation, ensure wiring connections are secure and the heater is not contacting plastic surfaces

Fixes warm fridge with cold freezer caused by frosted evaporator coils. This defrost thermostat regulates defrost cycles. Moderate DIY repair, 1-2 hours.

This holder element assembly secures the appliance's heating element in the correct position so the element stays stable for consistent operation and safe performance. It's a direct-fit replacement for worn or damaged holders. What it does:

• Secures and supports the heating element inside the appliance to maintain proper alignment
• Prevents element sagging or contact with other components that can cause noise or arcing
• Helps reduce vibration and movement that can lead to intermittent heating
• Common symptom: visible holder damage, loose or shifted element, unusual noise during operation

• Disconnect power (unplug or switch off breaker) before starting any repair
• Allow appliance and element to fully cool before handling
• Handle the element and holder carefully to avoid bending or damaging the element

Drain trough that channels defrost water to the drain pan in your top-mount refrigerator. Replace if cracked, warped, or missing to prevent leaks.

Replacement screw secures panels, brackets, and trim inside your oven or range. Restores tight fit when original hardware is missing, stripped, or damaged.

Replacement mounting screw for securing panels, trim, and internal brackets. Needed when original fasteners are missing, stripped, or damaged.