Parts for Ge GTE16DTHHRCC: Freezer Section Parts

The Actuator Air Foam is an OEM part for GE refrigerators responsible for redirecting the flow of air within the refrigerator's evaporator assembly, ensuring efficient cooling and temperature regulation.

A bad actuator air foam can be caused by normal wear and tear, exposure to moisture, or damage due to mishandling or impact. If you notice that your refrigerator is not cooling properly, or if there are temperature inconsistencies throughout the refrigerator compartment, it may indicate a problem with the actuator air foam.

Symptoms of a bad actuator air foam include:

• Inadequate cooling or freezing in certain areas of the refrigerator
• Temperature fluctuations within the refrigerator compartment
• Excessive frost or ice buildup on the evaporator coils
• Unusual noises coming from the refrigerator's cooling system

Replace your faulty actuator air foam with this genuine OEM part to restore your refrigerator. 

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

This reversible door plug fills the unused mounting hole when you switch the door swing on your refrigerator. It restores a finished appearance and helps keep air and moisture from entering through the opening.

• Covers the unused door hole created during a door swing reversal
• Helps maintain proper sealing and resists drafts/condensation at the opening
• Restores a clean, finished, factory look to the door
• Common symptoms: missing or cracked plug, exposed hole, cosmetic gap on door edge

• Disconnect power before servicing any door components
• Gently pry out the old plug with a plastic trim tool to avoid scratches
• Align the new plug with the opening and press until fully seated and flush
• Verify the door closes properly and the gasket seals evenly

The Air Tower and Evaporator Cover Assembly is an OEM part for GE refrigerators. This multi-piece component is located inside the refrigerator compartment and manages airflow that travels through the evaporator coil area. An attractive cover protects inner workings while directing optimal temperature control.  

Symptoms of a bad air tower assembly include:  

• Audible air disturbances accompanied by inconsistent interior temperatures
• Buildup of frost or moisture collecting outside the evaporator area
• Inability of warm food to adequately cool down inside the fridge  

Causes relate to cracks developing in thermoplastic covers after years of climate cycling strains. Closed airways may become obstructed as well affecting circulation.

This GE OEM replacement restores reliable humidity management and product cooling. Its enduring construction circulates purified air for consistent food holding at proper temperatures per federal guidelines. Compatible with GE and select Kenmore side-by-side models for direct fit airflow performance.
 

This freezer wire shelf provides a sturdy, level surface for organizing food in the freezer compartment. Replacing a bent, rusted, or missing shelf restores storage capacity and keeps items level and easy to access.

• Adds an additional storage level in the freezer for better organization and visibility
• Supports frozen items evenly to help prevent tipping
• Replaces a shelf that is broken, bent, rusted, or missing
• Resolves issues where the shelf won't sit level or securely in its supports

• Empty the shelf area; remove the old shelf by lifting/tilting and pulling forward from the side supports
• Align the new shelf with the correct slots or ledges; insert the rear, then lower the front onto the supports
• Ensure the shelf is seated level before reloading food; avoid overloading
• Disconnect power if working near internal lighting or wiring

The Evaporator Fan Rear Bracket is an OEM part for GE refrigerators. It supports and secures the evaporator fan at the rear of the refrigerator, ensuring it operates correctly to circulate air throughout the appliance.

Causes of a bad evaporator fan rear bracket can include physical damage due to impact, wear and tear from prolonged use, or corrosion from exposure to moisture.  

Symptoms of a bad evaporator fan rear bracket include:

• Unusual noises coming from the rear of the refrigerator
• Reduced cooling efficiency
• The evaporator fan becoming loose or detached
• Vibrations or rattling noises during operation

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Evaporator Fan Motor is an OEM replacement part for GE refrigerators. It is a crucial component responsible for circulating air and maintaining proper airflow within the refrigerator compartments.,This evaporator fan motor is designed to power the fan blades that draw air over the evaporator coils.

Symptoms of a faulty Evaporator Fan Motor include:

• Insufficient cooling or uneven temperature distribution within the refrigerator
• Excessive frost buildup or ice formation in the freezer compartment
• Loud or unusual noises coming from the fan area
• Complete failure of the fan to operate or turn on

Causes of a bad evaporator fan motor can include normal wear and tear over time, bearing failure, electrical malfunctions, or physical damage from foreign objects or debris.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore refrigerator models.

This is the evaporator fan blade that mounts on the freezer fan motor. It circulates cold air across the evaporator coils and throughout the compartments to maintain even, reliable temperatures. What it does:

• Moves air across the evaporator to cool and circulate airflow between freezer and fresh food sections
• Helps prevent warm spots and temperature swings inside the refrigerator
• Common failure signs include rattling/scraping noises from the freezer area
• Needed if the fan isn't moving air, the blade is cracked/loose, or cooling is weak despite the compressor running

• 1 evaporator fan blade

• Disconnect power before servicing; wear cut-resistant gloves around sharp sheet metal
• Remove shelves/drawers and the rear freezer panel to access the fan
• Pull the old blade straight off the motor shaft; transfer any clip/retainer if present
• Press the new blade fully onto the shaft; it spins freely without contacting the shroud before reassembly

The Fan Motor Grommet is an OEM replacement part for GE refrigerators. This small but essential component serves as a seal and insulator around the area where the fan motor shaft protrudes from the appliance body.

Causes of needing to replace the fan motor grommet can include normal wear and tear over time, exposure to extreme temperatures or moisture, or physical damage due to impact or improper installation.

Symptoms of a faulty or missing grommet include:

• Air leaks or drafts around the fan motor area
• Condensation buildup or frost formation near the motor shaft
• Increased noise or vibration from the fan motor assembly
• Reduced cooling efficiency due to air leakage

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore refrigerator models.

This defrost heater assembly melts frost from the evaporator during the automatic defrost cycle to keep airflow clear and temperatures stable. Replacing a failed heater helps restore consistent cooling and prevents ice buildup that blocks the freezer wall. What it does:

• Heats the evaporator coil to melt accumulated frost/ice during scheduled defrosts
• Keeps airflow paths clear to maintain proper temperatures
• Helps prevent excessive frost on the back panel or evaporator
• Common symptoms of a failed heater include heavy ice buildup, weak airflow, warmer fresh-food temps, and longer run times

• 1 defrost heater assembly

• Unplug the refrigerator before servicing; wear gloves—sheet metal edges can be sharp
• Access the heater behind the freezer's rear panel at the evaporator
• Note wire routing and connector orientation; secure the new element as originally mounted
• After installation, clear any remaining ice so airflow is restored before powering on

This element holder assembly secures an oven/range heating element and keeps it positioned for even heat delivery. It restores proper element alignment to reduce arcing and prevent rubbing or uneven baking. What it does:

• Secures the bake or broil heating element to the range/oven housing
• Keeps the element properly spaced for consistent heating performance
• Helps stop element movement, rubbing, or intermittent contact that can cause arcing
• Commonly replaced when the element is loose, misaligned, or makes noise during operation

• Disconnect power to the appliance before beginning any repair
• Handle heating elements carefully—sharp edges and fragile terminals can be damaged
• Verify element alignment and secure mounting hardware; replace only as needed
• If you see damaged element terminals or insulation, replace the element

The Air Tower and Evaporator Cover Assembly is an OEM part for GE refrigerators. This multi-piece component is located inside the refrigerator compartment and manages airflow that travels through the evaporator coil area. An attractive cover protects inner workings while directing optimal temperature control.  

Symptoms of a bad air tower assembly include:  

• Audible air disturbances accompanied by inconsistent interior temperatures
• Buildup of frost or moisture collecting outside the evaporator area
• Inability of warm food to adequately cool down inside the fridge  

Causes relate to cracks developing in thermoplastic covers after years of climate cycling strains. Closed airways may become obstructed as well affecting circulation.

This GE OEM replacement restores reliable humidity management and product cooling. Its enduring construction circulates purified air for consistent food holding at proper temperatures per federal guidelines. Compatible with GE and select Kenmore side-by-side models for direct fit airflow performance.
 

8-18 CA HX 1/2 S

This evaporator coil circulates refrigerant inside the freezer compartment to absorb heat and keep internal temperatures cold. Replacing a damaged evaporator restores proper cold transfer for reliable cooling performance. What it does:

• Absorbs heat from the freezer compartment by circulating refrigerant through the coil
• Helps maintain proper freezer and refrigerator temperatures when functioning correctly
• Common symptom: excessive frost or ice buildup on the evaporator fins
• Common symptom: warm freezer or refrigerator temps and longer run cycles
• Common symptom: compressor runs constantly or cooling becomes inconsistent

• Disconnect power to the appliance before any service to avoid electrical shock
• Refrigerant system access or refrigerant evacuation may be required; have a certified HVAC/refrigeration technician perform refrigerant work
• May require removal of interior panels, shelving, and insulation for access; follow factory service instructions
• Handle the coil carefully to avoid bending fins or damaging tubing

The Evaporator fan front bracket is an OEM replacement part for GE refrigerators. Located inside the freezer compartment, this bracket securely mounts and supports the evaporator fan assembly.

Causes of a bad front bracket include breakage from repeated fan motion, cracking from temperature fluctuations over many years, or loosening of mounting points.

Symptoms of a bad evaporator fan front bracket include:

• Abnormal rattling or vibrational noises coming from inside the refrigerator
• Reduced airflow circulation leading to ineffective cooling
• Potential shifting or misalignment of other evaporator components

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This factory screw secures brackets, panels, and internal components so assemblies stay tight and aligned. Replace a missing or damaged fastener to eliminate rattles, looseness, and misaligned parts. What it does:

• Fastens components, panels, hinges, or brackets to the appliance frame
• Helps maintain proper alignment and a solid, rattle-free fit
• Replaces stripped, rusted, or missing hardware
• Can address vibration noises and loose assemblies

• Includes 1 screw

• Unplug the appliance and shut off water before servicing
• Wear gloves; sheet-metal edges can be sharp
• Start threads by hand to avoid cross-threading; use the appropriate driver
• Tighten snugly—do not overtighten to prevent stripping