Parts for Ge PFSF6PKXGBB: 06 - Fresh Food Section Parts

The water filter is an OEM part for GE refrigerators. This filter removes or reduces various contaminants.

Features and Benefits:

• Easy DIY replacement, typically mounted inside the refrigerator at the back of the compartment.
• Removes or reduces various contaminants in your water and ice, including lead, cysts, asbestos, atrazine, , taste and odor, chlorine, sediment, turbidity, and more
• NSF/ANSI 42 and 53 standards
• 6 Month lifespan filter
• Carbon Block media
• Micron rating: 0.5-1 micron (Class I)

When to replace your filter:

• Bad taste or odor in water and ice
• Cloudy or discolored ice
• Reduced water flow or pressure
• Refrigerator replace filter indicator light is on

Note: If replacing the Culligan metal canister design filter for the first time, a special adapter, part number AP2615702 is needed, which is not included with this part. The compatible bypass cap is part number AP6891551.

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

Replaces the freezer evaporator defrost heater to melt frost and keep the evaporator fins clear during the defrost cycle, helping restore proper airflow and more consistent cooling when frost or ice builds up. What it does:

• Heats the evaporator fins during the defrost cycle to remove accumulated frost and ice.
• Common symptom: visible frost or ice buildup on evaporator coils or freezer walls.
• Other symptoms: reduced cooling performance or fluctuating/freezer temperatures that may indicate a defrost failure.
• Works as the heating element in the refrigerator's defrost system to prevent recurring frost accumulation.

What's included: One defrost heater. Install notes:

• Always disconnect power to the appliance before servicing to avoid shock or injury.
• Heater mounts near or on the freezer evaporator; access typically requires removing interior panels and the evaporator cover.
• Inspect wiring and connectors for damage; test the old heater for continuity before replacement.

This temperature sensor monitors internal refrigerator temperatures and relays them to the control, helping the unit maintain consistent cooling. Replacing a failed sensor restores accurate temperature regulation and more reliable operation. What it does:

• Measures compartment or evaporator temperature and sends a resistance signal to the control board
• Helps the control modulate compressor and fan run times for proper cooling
• Typical failure signs: sections too warm or too cold, erratic temperatures, or running longer than normal
• Causes inaccurate temperature readings compared to setpoints

• 1 temperature sensor assembly

• Disconnect power before servicing
• Access the sensor in the affected section; release any cover/clip and unplug the connector
• Route the new sensor's wiring like the original and ensure it's fully seated in its holder or clip
• Restore power and allow up to 24 hours for temperatures to stabilize

This damper motor assembly controls the refrigerator air damper to help regulate airflow between compartments, restoring proper temperature balance and reducing uneven cooling when the original motor fails. What it does:

• Moves the air damper to open or close airflow between freezer and fresh-food sections
• Allows the fridge control to direct colder or warmer air as needed for temperature regulation
• A faulty unit can cause symptoms like warm or inconsistent fresh-food temperatures, reduced cooling performance, or unusual clicking/noise at the damper area

• Disconnect power before starting; work on powered appliances can cause shock or injury
• Access typically requires removing interior panels or shelving to reach the damper housing
• Align the motor drive and damper linkage; don't force gears or clips when installing
• After installation, restore power and verify damper movement and temperature control operation

The water filter is an OEM part for GE refrigerators. This filter removes or reduces various contaminants.

Features and Benefits:

• Easy DIY replacement, typically mounted inside the refrigerator at the back of the compartment.
• Removes or reduces various contaminants in your water and ice, including lead, cysts, asbestos, atrazine, , taste and odor, chlorine, sediment, turbidity, and more
• NSF/ANSI 42 and 53 standards
• 6 Month lifespan filter
• Carbon Block media
• Micron rating: 0.5-1 micron (Class I)

When to replace your filter:

• Bad taste or odor in water and ice
• Cloudy or discolored ice
• Reduced water flow or pressure
• Refrigerator replace filter indicator light is on

Note: If replacing the Culligan metal canister design filter for the first time, a special adapter, part number AP2615702 is needed, which is not included with this part. The compatible bypass cap is part number AP6891551.

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

A single M4 tapping screw used to secure panels and components on compatible appliances. This screw provides a reliable fastener for plastic and thin metal parts, helping restore proper fit and reduce vibration or rattling. What it does:

• Secures trim, control panels, brackets, and covers where a self-tapping fastener is required
• Replaces stripped or missing screws that cause loose panels or parts
• Restores proper alignment and reduces noise from vibrating components
• Designed to form threads in softer materials for a tight hold

• Use the correct M4 driver bit and steady pressure to start the screw straight
• Do not over-tighten; stop when the part is snug to avoid stripping or cracking
• Replace only with the same size and type of screw for proper fit and function
• Disconnect power before servicing appliances to reduce shock risk