Frigidaire Cooktop Parts

This medium crown burner sits on the gas cooktop/range burner to shape and distribute the flame for even heating. Replacing a worn or damaged crown restores reliable ignition and a consistent flame pattern on the medium-output burner.

• Distributes gas evenly around the burner for steady, uniform heat
• Works with the igniter for reliable lighting when properly seated
• Helps protect burner ports from spills and debris
• Helps with uneven or yellow flames, delayed ignition, inconsistent lighting, or visible cracks/warping

• Disconnect power and shut off gas; allow the surface to cool completely
• Remove the old crown and clean the mating surfaces
• Align the new crown with any locator pins/notches and seat it flat; if screws are present on your model, tighten gently and evenly
• Restore gas/power and test for proper ignition and flame pattern

This electrical switch restores reliable on/off control to the designated circuit in your appliance. Replacing a worn or stuck switch helps ensure lights, fans, or motors operate only when they should. What it does

• Opens and closes an electrical circuit when actuated
• Helps correct issues like a light that won't turn on/off or a component that won't run or won't stop running
• Resolves intermittent operation caused by worn contacts or a loose/broken actuator
• Addresses signs such as melted/discolored terminals or an unusually loose/tight switch feel

• 1 switch

• Disconnect power to the appliance before servicing (unplug or switch off the circuit breaker)
• Access the switch location per your model's service information
• Photograph wire positions and transfer connectors one at a time to the new switch; do not force terminals
• Secure the switch, reassemble, restore power, and test operation

The Surface Element Control Switch is an OEM part for Frigidaire ranges. It is responsible for regulating the heat output of the surface elements on your range, allowing you to adjust the temperature for different cooking needs.

A bad surface element control switch can be caused by wear and tear, electrical issues, or component failure. When the control switch becomes faulty, it can result in issues such as the surface elements not heating up, inability to adjust the temperature, or inconsistent heat output.

Symptoms of a bad surface element control switch include:

• Surface elements not heating up
• Inability to adjust the temperature of the elements
• Surface elements heating unevenly or inconsistently

Replace your faulty surface element control switch with this genuine OEM Frigidaire part to restore your range's surface elements. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

This is the glass panel used in the oven door window. Replace it to restore a clear view into the oven and maintain the door's proper heat barrier if the original pane is cracked, shattered, or damaged.

• Forms the viewing window and thermal barrier in the oven door
• Helps the oven retain heat for consistent cooking
• Direct replacement for a cracked, shattered, or missing pane
• Typical symptoms: visible cracks, shattered glass, rattling fragments, or reduced visibility

• Disconnect power or gas and allow the oven to cool completely before service
• Wear cut-resistant gloves and eye protection; handle broken glass with care
• Support the door; remove the door and any trim as outlined in your model's service information
• Transfer any reusable brackets/trim from the original glass and avoid overtightening fasteners

The Cap-Burner is an OEM replacement part for Frigidaire cooktops. It is a component located at the top of each burner element on the cooktop. The cap-burner sits directly over the burner element to distribute and maintain heat levels evenly across the heating surface. 

Causes of a bad cap-burner can include warping or distortion from excessive heat exposure over time. Wet or sticky messes can also lead to clogging or blockages.

Symptoms of a bad cap-burner include: 

• Uneven or inefficient heating of pots and pans placed on the burner surface
• Hot spots or areas of excessively high heat 
• Burner elements that do not ignite or power on as expected
• Smoke or burning smells coming from below the cap-burner

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. 

The Surface Burner Cap is an OEM part for Frigidaire ranges. It fits over the surface burner, providing a protective cover while ensuring proper gas flow and flame distribution.

A bad surface burner cap can be caused by wear and tear, damage, or improper cleaning. When the burner cap becomes faulty, it can result in issues such as uneven flames, inefficient heating, or difficulty in maintaining a consistent temperature.

Symptoms of a bad surface burner cap include:

• Uneven or flickering flames
• Difficulty in reaching desired temperatures
• Excessive gas odor during burner operation

Replace your faulty surface burner cap with this genuine OEM Frigidaire part to restore your cooktop. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

This is a smoothtop assembly intended for use with ranges by major manufacturers. This component is located on top of the stove and protects the wiring and heating elements on the interior. The smoothtop assembly is made of strong glass. This part can become damaged and may be unsafe for use. If this happens, the smoothtop assembly will need to be replaced.A set of basic tools will be needed to replace this part. Work gloves can also be useful for preventing injuries from broken glass. First, turn off the range. Unplug it from the wall and make sure it is cool to the touch. Open the oven to remove the screws that hold the smoothtop assembly in place. Pick it up and disconnect the heating elements and wires. Next, install the new smoothtop assembly and hook back up the internal components. Plug in the appliance before use.This is an authentic OEM replacement component that is sourced directly from the manufacturer. It is sold on an individual basis. The smoothtop assembly is made to be used with ranges, ovens, and stoves created by Ikea, Frigidaire, and Crosley.

This ignitor orifice assembly routes gas to the oven igniter so burners light reliably. It replaces a damaged or clogged orifice to restore consistent ignition and safe burner operation. What it does:

• Directs gas flow from the manifold to the igniter/pilot so the burner can light
• Helps restore proper ignition when the burner sparks but fails to light
• Replaces corroded, clogged, or damaged orifice hardware that can weaken flame
• Works with standard oven/range ignition systems that use a separate orifice assembly

• One ignitor orifice assembly

• Turn off gas supply and disconnect power before attempting service
• Basic hand tools required; avoid overtightening fittings to prevent damage
• Check for gas leaks with a non-corrosive leak detector after installation

Used on the 2500 watt element

A safety thermostat that monitors and limits temperature at the range/stove backguard to help prevent overheating. Replaces a failed safety limiter to restore proper temperature control and safety operation. What it does:

• Acts as a temperature-limiting safety device for the range backguard assembly.
• Opens the circuit when temperatures exceed safe limits to prevent overheating.
• Commonly replaced when the oven or control fails to maintain temperature or shuts off unexpectedly.
• Helps address overheating, intermittent heating, or safety-trip symptoms tied to the backguard area.

• Disconnect power to the appliance before starting any repair to avoid shock or injury.
• Access may require removing the backguard panel and control housing; keep track of fasteners and wire routing.
• Verify electrical connections are secure and intact; replace only with correct part number.

This is a replacement screw used to secure appliance panels and components. It restores proper fastening so panels, trim, or assemblies stay tight and reduce vibration or rattling. What it does

• Fastens panels, brackets, or trim to the appliance chassis
• Helps stop loose or vibrating panels and trim pieces
• Restores proper alignment where a missing or stripped screw causes gaps or movement
• Use when the original screw is missing, damaged, or corroded

• One replacement screw as shown

• Disconnect power to the appliance before starting any repair
• Use the correct screwdriver or bit to avoid stripping the screw head
• Tighten until snug; avoid over-torquing which can strip threads or crack plastic
• Keep removed screws in a safe place; this screw matches the original before installation

This wiring harness routes power and signals between the appliance's control and various electrical components, restoring reliable electrical connections and helping the appliance operate as designed. Use it when wiring is damaged, corroded, or intermittent. What it does:

• Delivers power and signal paths between control boards, switches, and motors
• Restores lost or intermittent electrical connections that can cause failure to start or run
• Replaces burned, frayed, or broken wires and damaged connector terminals
• Helps eliminate arcing, shorts, and communication errors caused by faulty wiring

• Always disconnect all power (unplug or shut off breaker) before starting repairs
• Match connectors and wire routing to the original harness; avoid stretching or pinching wires
• Inspect mating connectors and terminals for damage before installation; replace any damaged parts
• If connectors are tight or corroded, clean or replace them rather than forcing connections