Parts for Frigidaire MCT1365L5: 04 - Functional Parts

Fix a microwave that won't start or stops mid-cycle with this monitor switch. Common safety component failure. Moderate DIY repair with basic tools.

Fix a noisy or overheating microwave with this blower wheel replacement. Restores proper ventilation and cooling. Moderate DIY repair in 30-45 minutes.

Replacement foot for countertop microwaves. Installs on the bottom to support and level the unit. Order if your original foot is cracked, broken, or missing.

A replacement 6-32 x 1-1/8 screw with an attached washer and pan-style head for securing appliance panels and components. Simple, direct fit for repairs that require the correct fastener to restore secure mounting. What it does:

• Fastens control panels, brackets, and trim where a 6-32 x 1-1/8 sems screw is specified
• The attached washer helps distribute load and resist loosening from vibration
• Replacing stripped or missing screws stops rattling and prevents parts from shifting
• Matches OEM fastening locations that call for a pan-head sems screw

• One replacement 6-32 x 1-1/8 pan head sems screw

• Use the correct 6-32 driver (Phillips) and turn carefully to avoid stripping the head
• Tighten until snug; avoid overtightening which can crack plastic or strip threads
• Disconnect power or follow manufacturer safety procedures before servicing electrical components
• Keep removed screws organized to ensure correct reinstallation

A single replacement mounting screw that secures the transformer to the appliance chassis. Keeps the transformer firmly attached to help maintain reliable power to the controls and reduce vibration-related noise. What it does:

• Secures the control/door transformer to the appliance chassis or bracket.
• Prevents transformer movement that can cause rattling or vibration noise.
• Helps maintain proper electrical connections by keeping the transformer stable.
• A missing or loose screw can lead to intermittent power to controls or unusual sounds.

• Always disconnect power to the appliance before starting work.
• Use the correct screwdriver to avoid stripping the head; tighten snugly but do not overtighten.
• Keep original hardware and screw length and thread match before installing.
• If the transformer or wiring looks damaged, replace or inspect components as needed before reassembly.

A single #8A x 1/2" screw used to fasten trim, panels, and internal components on compatible appliances. Small but essential, it restores secure mounting and stops loose parts from rattling or shifting. What it does:

• Secures panels, brackets, and trim to the appliance chassis
• Replaces missing, stripped, or corroded screws that cause rattling or loose fittings
• Provides proper thread engagement for consistent, reliable fastening
• Helps maintain alignment of components that depend on a correctly sized screw

• Disconnect power to the appliance before working on any electrical or mechanical components
• Use the correct screwdriver or bit to avoid stripping the head
• Thread carefully and avoid overtightening; snug is usually sufficient for sheet-metal fastening
• Keep removed fasteners in a small container to avoid loss during reassembly

This small plastic clip secures the dishwasher drain hose to the pump assembly or discharge fitting, keeping the hose in place and helping prevent leaks or disconnection during operation. What it does:

• Holds the drain hose firmly to the pump or outlet fitting to maintain a watertight connection
• Prevents the hose from slipping free during drain cycles
• Helps stop water leaks and washing chamber flooding caused by a loose hose
• Useful when replacing a cracked or broken retaining clip

• One drain hose retaining clip

• Disconnect power and water supply before accessing the dishwasher lower access area
• Remove the access panel or kickplate to reach the drain hose and pump connection
• Use pliers or a flat tool to remove the old clip and snap the new clip over the hose/fitting until fully seated
• After installation, run a short drain cycle and inspect for leaks; re-secure if necessary

The Frigidaire Touch-Up Paint is white in color in a .6 fl oz bottle. For almond order 5303321320. For black order 5303321321.

The Touch Up Paint is an OEM part for Frigidaire appliances. Whether you're dealing with scratches, chips, or other minor cosmetic damage, this touch-up paint provides an easy and effective solution for maintaining the appearance of your appliance. It's designed to adhere well to metal surfaces, offering durability and resistance to further wear and tear.

Over time, appliances can accumulate minor surface damage from regular use, cleaning, and accidental impacts. Using the Touch Up Paint not only improves the aesthetic appeal of your appliance but also helps protect exposed areas from rust and corrosion, which can extend the life of the appliance.

Symptoms of needing Touch Up Paint include:

• Visible scratches or chips on the appliance's surface.
• Areas of rust or corrosion that need to be covered after treating the rust.
• The desire to maintain or improve the appliance's appearance for aesthetic reasons or to maintain its value.