Parts for Ge ZGW124EN2SS: 01 - Gas Range Parts

This small trim ring restores the finished appearance around a control or element opening and helps protect the underlying mounting area from dirt and moisture. It replaces a worn, cracked, or missing decorative bezel for a clean fit. What it does:

• Covers the gap around a control, switch, or element mount for a finished look
• Protects the exposed mounting area from debris and light moisture
• Prevents rough edges from catching or damaging knobs and controls
• Helps keep replacement parts aligned and properly seated

• Disconnect power to the appliance before starting any work to avoid shock or injury
• Typically installs by snapping into place or securing with existing screws/clips; reuse original fasteners unless new ones are provided
• Inspect adjoining seals and components for damage when replacing the trim ring

This glass-ceramic cooktop surface replaces the top cooking surface on compatible radiant electric cooktops, restoring a smooth, heat-safe work area for cookware and controls. Designed to match OEM fit and finish. What it does:

• Replaces a cracked, chipped, scratched, or otherwise damaged cooktop top to restore a smooth cooking surface
• Provides the durable, heat-resistant surface that supports cookware and transmits heat from radiant elements
• Helps prevent food and liquid from contacting internal components through a sealed cooking surface
• Restores proper alignment for burners and control openings for reliable operation

• One glass-ceramic cooktop surface

• Disconnect power to the range/cooktop at the breaker before beginning; glass parts can break if mishandled
• Handle with care and use appropriate gloves to avoid cuts; support the glass fully during removal and installation
• Partial disassembly of the cooktop and removal of trim or screws may be required

This strain relief secures the appliance power cord where it enters the cabinet, preventing pull, chafing, and wire stress for safer, more reliable power connections. It's a simple, low-cost part that helps protect wiring from damage. What it does:

• Clamps and holds the power cord to reduce strain on internal wiring and terminal connections
• Helps prevent cord pull-out, fraying, and exposed conductors that can cause intermittent power or arcing
• Keeps the cord routed and positioned to reduce vibration wear over time
• Commonly replaced when cords are loose, damaged at the entry point, or when the clamp is broken

• One strain relief clamp

• Disconnect power at the breaker or unplug the appliance before starting any work
• Remove the access panel or back panel as needed to reach the cord entry; keep fasteners for reassembly
• Position the cord, seat the strain relief in the cabinet opening, and secure per original mounting (screws or snap-fit depending on model)
• After installation, restore power and verify steady operation; stop and recheck if you see sparking, burning smell, or intermittent power

This 4-point spark igniter module supplies timed spark to four burner electrodes so a gas range lights reliably. It replaces a failed ignition control to restore consistent, on-demand sparking across the cooktop. What it does:

• Sends high-voltage spark to up to four burner electrodes to ignite gas burners
• Replaces a faulty module that causes no spark or no ignition at affected burners
• Common symptoms it can fix: burners won't light, intermittent ignition, or continuous clicking from the cooktop
• Helps stop arcing or misfiring when the control has failed

• Disconnect power to the appliance before starting work; if you smell gas, shut off gas and ventilate before proceeding
• Label or photo all wire connections before removal to ensure correct reassembly
• Handle the module and electrode leads carefully; avoid bending or contaminating electrode tips
• After installation, restore power and test each burner for proper spark; if you detect gas leaks or continued problems, stop.

This replacement back-right gas tube routes gas from the valve to the rear burner for proper combustion. It restores the correct gas flow path so the burner can light and maintain a steady flame when installed correctly. What it does:

• Directs gas from the valve to the back-right burner for ignition and operation
• Helps achieve a stable, even flame at the rear burner when functioning
• Replaces damaged, bent, or corroded tubing that can disrupt gas flow
• Can resolve symptoms like weak or no flame at the rear burner and uneven heating

• One back-right gas tube

• Turn off gas supply and power before attempting any service
• Inspect fittings and gaskets; replace any worn seals to prevent leaks
• Tighten connections to manufacturer torque specs and test for leaks with a soap solution or gas leak detector