Martin M Saratoga , CA July 10, 2017 Appliance: General Electric Microwave PEM31SM4SS Door wouldn't open pem31 ge microwave oven The door latch is opened by the lever switch, which sits on a plastic peg on the body latch - part AP3186330. This plastic peg had broken. Talking to the dealer, it sounds like a common problem. It's fairly simple to open the cabinet and remove the old part. The manual claims that the big capacitor has a self-discharging circuit, but it's best to briefly short it out with a resistor just to be sure. The biggest issue is the three electrical interlock switches that also click into place on the body latch. The little latch-tabs that hold those switches in place are quite weak, and I broke one while trying to install it - it broke way too easily in my opinion! Before removing the switches from the old unit, label them and take a few photos so you know which wires go where.. It's very hard to replace the switches when the new latch-stopper in replaced in the oven. The best option is to remove the wires from the switches, click the switches into place on the body latch outside of the oven, replace the body latch in the oven, and then re-connect the wires to the switches. Read More... 5 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: 15-30 minutes Tools: Pliers, Screwdrivers
Jeffrey A Trabuco Canyon , CA November 28, 2016 Appliance: Model PEM31SMSS Ge profile spacemaker ii microwave oven pem31smss door does not open Although it looked perfectly fine. I replaced the Body-Latch (AP3186330 / WB6X10424) and it fixed the problem. Door opens like new again. Read More... 1 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: 15-30 minutes Tools: Pliers, Screwdrivers
John S Point Roberts , WA January 08, 2018 Appliance: General Electric Microwave PEM31DM3WW Door wouldn't open The body latch is a replaceable plastic molding that hold 3 micro switches and a pivot post needed for the door opening mechanism. I suspect that post will often fail, as it did for me, by breaking off. The repair is straightforward: 1) Remove cover. You will need a security torx bit for a couple of the screws. 2) With a screwdriver push up the bottom door latch hook so that the door will open. 3) Take a picture of the body latch area so you don't get the wires mixed up. 4) Remove wires from micro switches. 5) Remove the 2 screws that hold the body latch. Remove body latch. 6) Swap micro switches and the plastic part that pivots on the post onto new body latch. 7) Install new body latch and reconnect wires. There is some movement possible around the screw holes so after tightening make sure the micro switches are engaged when the door is closed. 8) Test door closing/opening and proper functioning of the touch pad. 9 Reinstall cover. Read More... Do-It-Yourself Rating: Repair Time Estimate: 30-60 minutes Tools: Pliers, Screwdrivers
David B South San Francisco , CA October 18, 2019 Body latch pin broken With new body latch from Appliance Parts Pros.com. Read More... Do-It-Yourself Rating: Repair Time Estimate: 15-30 minutes Tools: Screwdrivers
Will R Durango , CO January 13, 2020 Appliance: Model GENERAL ELECTRIC JEM25 Microwave runs when door is opened YouTube is a great source of info on how to fix most anything. From watching a few videos, it was obvious that my microwave's problem was the door switches. When I took it apart, I noticed that the body latch (the plastic frame that holds the switches) had a broken part. Appliance Parts Pros was a good place to order parts from because I could enter the model number and easily locate the correct parts for that model. APP was a little pricey on the parts and shipping, so I opted to purchase the plastic body latch from them (I couldn't easily find the correct one elsewhere). I purchased the switches elsewhere for 1/3 the APP cost, but it took some effort to make sure I ordered the right ones. We had taken photos of the switches before we disassembled them, so that helped a lot in getting them back in the right places and the wires attached to the correct terminals. Overall, it was an easy fix and we saved our microwave for about $35 by fixing it ourselves. Read More... Do-It-Yourself Rating: Repair Time Estimate: 1-2 hours Tools: Pliers, Screwdrivers