Generac Gasket & Seal

This factory washer is used in appliance assemblies to distribute load under a fastener and maintain a secure, accurate fit. Replace a missing or damaged washer to restore proper stack-up and reduce vibration, noise, or loosening.

• Distributes load and provides proper spacing in the fastener assembly
• Helps keep bolts, screws, or nuts tight to minimize vibration and rattling
• Direct replacement when the original washer is worn, bent, cracked, or missing
• Typical signs include loose panels/brackets, recurring looseness after tightening, or new vibration after service

• Unplug the appliance; shut off water supply if working near hoses or valves
• Note the original hardware stack-up and reassemble in the same order
• Inspect mating surfaces and companion hardware; replace any damaged parts
• Tighten fasteners snugly per service guidance; avoid overtightening

This is a carburetor gasket replacement that is for use with generators. The gaskets are an important feature of any engine. The gasket will help to provide an airtight seal for the carburetor. This will ensure that there is not too much air getting into the carburetor, which could cause problems with the air to fuel mixture. Too much air could mean that the engine will have trouble running. It could start to stall out. To ensure that the engine is performing properly, owners will want to check their carburetor gaskets. The gaskets will start to wear down over time. They can stretch and they can start to dry out and break. This means they will no longer provide an airtight seal. Owners should check their gaskets if they are noticing the generator's engine has trouble running and not stalling. When performing maintenance on the carburetor or rebuilding the carb, they should replace the gaskets. This is a genuine OEM part that has been sourced from Generac. The carburetor gasket is sold individually and is specifically for use with generators from Generac.

This is an authentic carb to air cleaner gasket sourced from Generac. The gasket is placed between the air cleaner and the carburetor, and it will act as another means to reduce the amount of air that is coming into the carburetor. This is important because if there is too much air, it will affect the fuel-air mixture that is going into the carburetor. This could result in problems with the engine's performance and consistency. The carb to air cleaner gasket will start to wear out the longer it has been used. It can start to dry out and crack, and parts of it could break off entirely. This would mean more air can get into the engine. To prevent this, owners will want to make sure that they check on the gasket and replace it as needed. This should be a part of the routine maintenance of the small engine. The carb to air cleaner gasket is a genuine OEM product that is sold individually. It is designed for use in certain models of Generac small engines, such as those found in generators and gas-powered pressure washers.

This Generac insulator gasket is for Generac brand generators. It is used to keep heat from the engine away from the carburetor. The longer the generator runs, the warmer it will get, and a properly functioning Generac insulator will prevent the device from overheating. After use and with normal wear and tear, these Generac insulator gaskets will begin to wear down and become ineffective. Users will notice the generator is getting too warm after running for some time, or the entire device may fail. A worn down or damaged insulator gasket must be replaced before continuing operations of the generator.Replacing a Generac insulator gasket can be done relatively quickly with the proper tools. Always wear protective gloves when repairing any engine components. Remove the old or ineffective gasket before replacing it with a new one. Ensure all parts are lined up and secure before starting the machine.This Generac insulator gasket is an authentic OEM replacement part. It is sold as an individual unit. The insulator gasket is for Generac brand generators only, and it fits several different models. The replacement part is made of high-quality, durable materials.

This carburetor gasket manages airflow around the motor. It is part of all carbureted engines and if it malfunctions, it allows air to be where it shouldn't. This alters the air to fuel ratio and can cause reduced performance or failure. If the gasket fails, it needs to be replaced promptly, because the engine will still run but will suffer damage if the gasket is allowed to leak air into or out of the motor. Replacing this part means taking apart the carburetor and cleaning all of the different components. It may also mean using the appropriate gasket sealer, though this varies based on the make and model of the engine or machine. This genuine OEM carburetor gasket is designed for Generac portable generators. It is shipped individually and will not include any other items, including sealants or oils.

The air cleaner gasket is placed between the air cleaner and the carburetor, which can help to ensure that the carb is getting the correct amount of air, while also providing some protection. The gasket can start to wear out eventually. It might become brittle and crack, or it might no longer sit properly, reducing its efficiency. If the air cleaner gasket has problems, it is important to replace it as soon as possible. Gaskets that are not working properly and that allow too much air to pass through could cause the engine to have trouble starting and operating. Replacing the filter is relatively simple. The air cleaner gasket is an authentic OEM part that is sold separately. This gasket is for use with power washers and generators from the Generac brand.

This is a replacement carburetor gasket. The gasket plays an important role in the carburetor. It helps to ensure that there is no additional air getting into the carburetor. It also ensures no dirt or other debris makes it into the carburetor. If the gasket is not working properly or has been damaged, air and other elements that get into the carburetor could cause the engine to run rough. It could also make it more difficult to start the engine.Over time, the carburetor gasket will wear down and will need to be replaced. Gaskets will dry out and crack the longer they've been used. There is also the possibility that the gasket has not been seated properly, which would require repair. Whenever owners are servicing the carburetor, they should make it a point to replace the gaskets, even if they appear to be in serviceable condition.This gasket is an OEM replacement part sourced directly from the manufacturer. It will work for certain models of carburetors from Tecumseh and Craftsman. Each of the gaskets is sold individually.

The oil seal is designed to stop fluid from leaking out, as well as to ensure that dirt and other debris do not make their way into the oil. When applied properly, it should create an impermeable seal. It also provides spacing between the crankcase and the crankshaft. If the oil seal has been damaged or has degraded because of wear and tear, it will need to be replaced. Some of the signs that the oil seal might be bad include leaks or an engine that is not performing properly. Users might also notice that the machine is going through oil quickly. This is an authentic OEM product that is sold individually. The oil seal can be used with many types of lawn and garden equipment including lawn mowers, snowblowers, tillers, pressure washers, wood chippers, generators, and other small engines. Compatible brands including Briggs & Stratton, Simplicity, Snapper, MTD, Lawn-Boy, Tecumseh, Cub Cadet, Toro, and Craftsman.

This genuine carburetor insulator gasket is designed for use with select generators. The carburetor insulator gasket is designed to be installed between the carburetor and the engine block, providing an insulated seal that keeps air out and ensures that the engine is operating at peak performance. Gaskets are subject to a lot of pressure and high heat with regular use and will degrade or warp over time. This can result in leaks and other issues, so gaskets should always be replaced immediately. This OEM carburetor insulator gasket can provide an exact fit for compatible machines. This is a genuine product that is manufactured to exact standards by Generac. It is designed for use with select models of their generators. The gasket is made from durable composite materials and is sold as an individual unit. Gaskets are typically considered a part of routine maintenance and some people will purchase an extra unit to keep on hand in case of emergency repairs. This carburetor insulator gasket does not include any hardware or additional parts. A wrench set will be required for replacement. Always wear gloves when performing engine maintenance and repair. Repairs should never be performed on a hot engine.

This genuine Tecumseh cylinder head gasket cover can be used as a replacement part for the small engine of a snowblower or a tiller. The cylinder head gasket seals off the cylinder head from the engine block. The function of a cylinder head gasket cover is to protect the cylinder head from damage and provide additional insulation.A cylinder head gasket cover might suffer damage over time from general overuse or wear and tear. This damage can come in the form of punctures, piercings, and corrosion to the cover that chip away at the gasket cover's ability to protect the cylinder head gasket and seal it off. If cylinder head gasket cover shows these signs of damage, it should be immediately removed and replaced with this genuine OEM part. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This is an OEM part sourced directly from the manufacturer. It is sold individually. This cylinder head gasket cover is compatible with the following brands: Tecumseh, Toro, Craftsman, and Husqvarna.