Need Help?
Call or text
Usually ships within 4 - 14 days
Replaced drain hose and clamp. Read more
The Washer Drain Hose is an OEM replacement part for Frigidaire washing machines. It is a flexible, 7 ½ ft plastic hose that connects the washer tub to the household drainage system. The drain hose removes water from the washer at the end of each cycle. Symptoms of a faulty drain hose include:
Causes of a bad drain hose include kinks or bends that restrict water flow, cracks or holes from wear and tear, and blockages from accumulated debris. These issues can compromise the hose's ability to drain water properly.
This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.
Simply open the top of the washer by inserting a putty knife (watch YouTube ) and then the front panel by removing two bottom philips head screws on the front. The whole front panel comes right off. Using pliers the spring clams holding each hose, they come off and each hose is replaced. The drain one was only leaking but since it has open I changed both and even the drive belt. Whole job less than 1 hour. BTW parts arrived next day! Read more
The Agitator Hub is an OEM part for Frigidaire washing machines. It connects the agitator to the drive shaft, enabling the agitator to rotate and move clothes effectively during the wash cycle.
Causes of a bad agitator hub can include wear and tear from frequent use, exposure to harsh detergents or hard water, or damage from overloading the washer.
Symptoms of a bad agitator hub include:
This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.
The agitator stopped functioning and there was a squeaking sound occurring in agitation mode. I found that if I cranked down on the agitator cap, screwing in as hard as I could, the agitator would work briefly, then the cap would loosen and agitator stop moving. I removed the agitator cap, along with which came the agitator stud cap and a rubber washer/seal which was jammed up into the underside of the cap. I lifted out the agitator from the drum and inspected it and the hub best I could.... Read more
This agitator is a genuine Frigidaire part, sold individually. This agitator can be used as a replacement part for a washing machine or a washer/dryer combination appliance. This part rotates within the tub of the washing machine so that clothes and other items are tumbled around and fully cleaned.If an agitator has been subject to damage at some point in the standard lifespan of a washing machine, symptoms of damage will manifest in the form of a washing machine that will not agitate in a normal laundry cycle. If this is occurring, the agitator should be inspected for visible signs of damage, including punctures, scrapes, tears, and erosion to the material that could preclude it from serving its function. If the agitator seems damaged upon assessment, it should be removed and replaced with this genuine OEM replacement part before using the washing machine again.This is an OEM part sourced directly from the manufacturer. It is sold individually. This agitator is compatible with the following appliance brands: Frigidaire, Kenmore, Gibson, and Kelvinator.
I own several apartments with same washer/dryer combo. A couple months ago, one of my washers stopped agitating. I hired an Appliance Repair Company. They charged my $95 for agitator, $65 for hub and $120 for service call, plus tax for a total of $310. Oh, and it took them FOUR WEEKS to get the part in and fix my washer!. Something to do with "Frigidaire shipping issues". Last week I had another unit break with same problem. Ordered parts from AppliancePartsPros.com for $80, parts arrived... Read more
We had a power surge that tripped the washer breaker. It showed an E23 error code so I replaced the main control board (part number AP4362398.) All washer activity back to normal except it still wouldn't spin and still had E23 code. I removed the tub to pump hose (part number AP3837322) to find all sorts of goodies inside such as underwires from bras, a quarter, nickel, penny, and dime stacked perfectly on top of each other inside the filter, and tangled yarn from a rug. Ended up replacing the... Read more
The trunnion is the hub that mounts the washer's inner tub to the drive shaft. Replacing a worn hub restores a solid, centered connection so the basket spins smoothly without wobble, slip, or grinding. What it does:
The seal at the bottom of the tub had started to fail. On large loads water would leak so I ordered a new one rubber seal. Getting the trunnion off the transmission shaft was hard as it was calcified and corroded. I used a wire brush to get some of it off and then used a lot of WD-40. The bolt holding the trunnion plate on sheared off when I tried to remove it on one side and the other came out ok (the bolt hole through the trunnion is not threaded so it should slide out once the plate is off... Read more
This is a transmission assembly for washing machines. The transmission assembly is the gearbox in the washing machine's motor that allows the washing machine to work at different speeds and different intensities. If the washing machine is no longer spinning properly and has lost its normal level of washing power, it could mean that the transmission assembly needs to be replaced. Luckily, replacing this part is not as difficult as it might seem at first glance.To replace the transmission assembly, begin by unplugging the washing machine. The first step is to remove the upper control panel. Pull forward on the bottom of the console and remove the two retaining clips as well as the harness connector to the lid switch. Using a flathead screwdriver remove the clips. After this, remove the entire cabinet from the back panel to gain access to the interior of the washer. Remove the 7/16 bolt from the agitator and pull it straight up to remove it from the shaft. Once completed, gain access to the motor and pump and remove by releasing the screws and tabs that attach it. Remove the wire harness attached to the transmission. Remove the bolts that secure the motor mount to the transmission and proceed to pull the old transmission out of its place. Install the new transmission and reassemble the other parts.This genuine OEM replacement part is compatible with Frigidaire, Electrolux, Gibson, Kelvinator, and Westinghouse washers. It is sold individually.
Replace with a new assy Read more
Replaced transmission. If you have a laundry center like me, you don't have alot of space. Replacing the parts want difficult. Just limited space made it harder. Also couldn't find a removal video for one of these but using a video for a frigidaire stand alone washer ouput me in the ball park and figured it out from there. Appliance parts pros had the best process too! Read more
The lady that talked to Fred gave him great help. She told him how to take the front off to replace the part. It only took a couple of minutes to do the repair. Even though I work for Sears parts dept. he didn't think I knew what I was doing.. Read more
Outer door panel that replaces a damaged or worn outer door surface, restoring the appliance's finished exterior and protecting inner door components. Ideal when the exterior is dented, scratched, or cosmetically damaged. What it does
Purchased the door panels (both sides) and replaced them both. Not sure if spending $150 on door parts for a 15 year old washer was a great investment, but the parts worked great. Took maybe five minutes to put it all back together. Read more
This replacement upper agitator restores the washer's normal wash action by moving clothes and improving water circulation for better cleaning. It fits the factory agitator location and replaces worn, cracked, or damaged agitators to restore performance. What it does:
Replaced the damaged agitator with a new one. After watching the youTube video from this website. Read more
My washer and dryer was stacked and I needed the right parts to put the tops and "feet" back on them. Read more