Gibson Washer Parts

• Lid or door will not open
• Won't start
• Lid or door won't close

Just removed the old and put on the new,simple.On this Fridgidare washer you should lift the door as you close it which should make the striker last.. Read more

I ran a diagnostics check on the washing machine and came up with the error code E47 -Board thinks the door PTC circuit is open in spin. The washer thought the door was open and would not finish the spin. I was left with a washer full of very wet clothes. This repair was SO extremely easy. I only needed to uses a pair of needle nose pliers and a screw driver. It took less than 10 minutes, start to finish. Now the new door lock assembly registers correctly and my clothes are completely... Read more

• Will not drain
• Noisy

So, Saturday, the washer wouldn't drain, yes, I tried the Drain/Spin cycle. So I took the clothes out, rinsed them out twice in the laundry sink and dried them. After a quick Google search, I came to the conclusion that the pump was bad and ordered a pump, $125. Over the course of the next four days, expecting the new pump on Thursday, I baled out the washer, pulled it out from the wall and propped up the front (it's HEAVY), removed the front access panel, removed the drain inlet and outlet... Read more

• Spins slowly
• Burning smell
• Pumps but will not spin
• Will not agitate

I replaced the spin bearing, tub seal, washer and drive belt since I had it all apart. The video was extremely helpful...I would have tore the whole thing apart trying to figure out how the agitator came off....but it was very simple. Read more

• Will not drain

Replace the drain pump after watching a video demonstrating the process. The washing machine had run properly and emptied, so I was surprised how much water remained in the pipe after disconnecting the old pump. Plan on having 2-3 large towels underneath before removing it. The most difficult part (and most irritating) was replacing the intake and outtake hoses with the existing spring clamps. The drain hose into the pump took almost twenty minutes to attach properly. If the hardware store was... Read more

This was a fairly easy fix. The only problem I had was that the cover over the retaining nut was difficult to pull off. I changed to a larger pair of pliers and put a little more muscle to it and it popped right out. There was a little corrosion on the shaft that needed to scraped off for the new agitator to slide on easily but after that was gone the new part slid on and with some downward pressure it seated in. Read more

• Spins slowly

With more difficulty and frustration than expected but it works fine now. Things learned: 1. Order only 3 replacement pins. One comes with the shocks that you can't be sure you see in the picture. 2. A circuit board in a plastic box mounted to the floor, left rear, must be removed by two screws to be able to get pliers onto the head of the pin more easily. This helps installation too. 3. A 1/2" deep socket pushed onto the retaining tab of the pin stays there while you pull with pliers from the... Read more

I replaced the spin bearing, tub seal, washer and drive belt since I had it all apart. The video was extremely helpful...I would have tore the whole thing apart trying to figure out how the agitator came off....but it was very simple. Read more

• No hot or cold water
• Will not stop filling with water
• Will not fill with water
• Leaking

This is my third repair of this type. The first was a stand-alone washer and was very easy, because there was a plate on which the inlet valve assembly was mounted, and it was easily removed. This repair was on a Frigidaire stacked washer/dryer (laundry center). Stacked washer/dryers are typically purchased to save space and are often tucked into a closet. Be sure you can pull it out to access both front and rear. Remove drain hose from drain, detach water hoses, electricity and dryer vent... Read more

Replaced the rear drum bearing assembly and the front top felt that the drum rides on and since I has it apart installed a new belt. Simple to do and takes very little time! Read more

Replaced springs and shocks. Read more

• Shakes and moves

With more difficulty and frustration than expected but it works fine now. Things learned: 1. Order only 3 replacement pins. One comes with the shocks that you can't be sure you see in the picture. 2. A circuit board in a plastic box mounted to the floor, left rear, must be removed by two screws to be able to get pliers onto the head of the pin more easily. This helps installation too. 3. A 1/2" deep socket pushed onto the retaining tab of the pin stays there while you pull with pliers from the... Read more

• Timer will not advance

I replaced the timer Read more

• Timer will not advance

I ordered the timer and knob on Monday, they arrived around noon on Tuesday, and within an hour I had them installed and back in business. I was amazed how quickly the parts got here. The online video showing the procedure step by step was very helpful. Instead of disconnecting all the wires and having to keep up with which one went where, I moved each wire one by one and made sure I didn't get any of them in the wrong place. The only thing that slowed me down a bit was seeing which side of the... Read more

Our washer is next door the bathroom. So when, during the rinse cycle, the hose split and we found the back of the house completely flooded I initially assumed the culprit was either the toilet or the sink or possibly an interdimentional portal into a demonic netherworld of vaguely chlorine scented water. I spent the next hour mopping it all up and checking and re-checking the pipes in the bathroom with no apparent leaks. The next load of laundry left more clues as this time the flood was from... Read more

• Will not stop filling with water
• Will not fill with water

Part arrived in one day! Replaced the water valve. YouTube video for replacing water valve on Frigidaire top-loading washers was spot-on. Read more