Parts for Ge AEQ12DPS1: 01 - Grille & Chassis Parts

This vertical louver restores proper airflow and appearance for the appliance's vent or air channel. It directs air and protects internal components while keeping the exterior looking finished. What it does:

• Directs and guides airflow through the appliance vent
• Protects internal components from large debris and improves venting performance
• Helps reduce rattling from a damaged or loose vent louver
• Restores the appliance's exterior look when the original louver is cracked or missing

• One vertical louver

• Disconnect power (or unplug) before accessing the vent area to avoid electrical hazard
• Remove any fasteners or clips holding the old louver; retain hardware
• Align the replacement louver with mounting slots or tabs and secure with original screws or clips
• If edges are sharp or fit is tight, wear gloves and test operation before reassembly

Traps dust and lint to protect your air conditioner's evaporator coil and maintain airflow. Replace when clogged to restore cooling performance.

Filter sub-assembly replaces the refrigerator's water-filter housing, holding the cartridge and directing water to the dispenser and ice maker. Restores secure cartridge seating and consistent water flow when the housing is damaged. What it does:

• Holds and seals the cartridge to help prevent leaks at the filter location.
• Directs filtered water to the dispenser and icemaker plumbing.
• Commonly replaced for leaks at the filter area, reduced water flow, or a loose/ill-fitting cartridge.
• Intended for cartridge-style refrigerator water-filter systems.

• Turn off the refrigerator water supply and relieve dispenser pressure before removing the old filter housing.
• Use basic hand tools; inspect and replace any worn O-rings or seals to ensure a proper seal.
• After installation, restore the water supply, check carefully for leaks, and run/flush water per refrigerator guidance.

Complete cabinet assembly housing for room air conditioners. Replaces cracked, damaged, or worn outer casings. Structural component for unit protection.

Cabinet connection bar secures panels to the air conditioner frame for stable alignment. Replacement needed when bar is bent, broken, or missing.

This curtain assembly replaces the inner door curtain on compatible GE over-the-range and countertop microwaves to restore the door's interior cover and help maintain proper operation and shielding. It's a direct-fit replacement sold individually. What it does:

• Replaces a cracked, warped, or missing inner door curtain that can expose internal components
• Helps restore the door interior, which can reduce visible light leaks and improve door integrity
• Addresses issues such as rattling or loose interior door panels during operation
• Compatible with service procedures that require removing and replacing the door inner curtain

• 1 curtain assembly

• Unplug or disconnect power before starting any repair; service only with unit de-energized
• Handle door components carefully to avoid damaging glass, seals, or the new curtain
• Removing the outer door and/or inner door liner may be required;

Extendable side panel that fills the gap between your window A/C and frame. Replace cracked, broken, or missing curtains to block drafts and debris.

Replacement top rail for room air conditioners. Installs along the upper edge of the unit. Needed when original rail is cracked, bent, or broken.

Gasket seal for air conditioners. Replace if you notice air leaks, reduced cooling efficiency, or visible wear. Verify fit with your model number.

This door gasket seal replaces a worn or damaged refrigerator or freezer door seal to restore a tight closure and help maintain proper temperature. It helps stop air leaks that can cause frost build-up and higher energy use. What it does:

• Forms a replacement seal around the appliance door to maintain an airtight closure
• Helps reduce interior temperature fluctuations that can lead to frost or spoiled food
• Restores proper door alignment and sealing where old gasket is cracked, torn, or compressed
• Commonly used when you see visible gaps, drafts, or persistent moisture at the door edge

• Designed for a direct OEM-fit; inspect the door channel and mounting surface before installing
• Clean the gasket channel and door edge to remove debris for best sealing contact
• Warm the gasket slightly (per OEM guidance) if needed for easier fitting; avoid open flames

Replace your air conditioner gasket seal to prevent air leaks and maintain cooling efficiency. Install when worn or damaged. Verify fit with your model.

Gasket seal for room air conditioners. Replace if you notice air leaks, reduced cooling efficiency, or visible wear. Verify compatibility with your model.

Hardware installation assembly for air conditioners. Includes screws, nuts, and washers for secure mounting. Replace missing or stripped fasteners.