Parts for Craftsman 358791031: Handle / Driveshaft / Shield Parts

This throttle assembly cable is manufactured by Craftsman, but also used by Poulan, to regulate the flow of fuel to certain small gasoline-powered engines. This assembly houses the throttle trigger that is used by almost a dozen different machines, including not only trimmers, but also pole saws and other small gasoline-powered tools. Apart from the cutting edges of the pole saws and trimmers, the parts of these devices that sees the most wear and tear, and is most likely to fail, are the throttle assemblies. Whether banged about because of proximity to the throttle trigger or simply because it's the only part protruding from the mid-body of the typical weed cutter, the throttle assembly housing and cable are susceptible to failure. Most often, failure of the cable is the result of one of the buds, attached at the ends to clasp securely, having broken off. In this case, the gasoline engine may start, but will not rev or only does so sporadically. Replacing the cable is a matter of removing the throttle housing and trigger as well as detaching the cable from the carburetor. When replacing the cable, be sure to use one like this, which is a genuine OEM replacement part, manufactured to replicate the specs of the original.

This replacement part is a screw. This part is a genuine replacement part made by Husqvarna. Screws are small but important in many different types of machinery. Screws are able to hold different parts in place and help them stay secure during use so that the machine can operate smoothly and efficiently. A new screw might be needed if the current one is missing or damaged in any way. It is possible that the screw can become stripped over time and therefore not stay in place properly. If this is the case it is recommended that it be replaced. This repair should be fairly easy and only require a screwdriver and possible pliers. This part is sold individually and is sourced directly from the manufacturer to ensure proper fit and long-lasting use. Note that This is a genuine OEM replacement part.

This is a replacement purge bulb. This is a genuine OEM part made by Husqvarna and has been sourced directly from the manufacturer. This part is intended to replace a broken or defective purge bulb on various models of outdoor power equipment. The purge bulb purges air from the carburetor and draws in fuel from the fuel tank to allow the engine to start. Over time, the purge bulb can crack or become brittle, requiring replacement. Proper tools are required to replace this part and work gloves are advised. It is always recommended that the appropriate safety precautions are adhered to when attempting to fix any power tools or machinery. When working on or near an engine, ensure the equipment is turned off and completely cooled down before starting any repairs. For more accurate information on how and where to install this purge bulb, the appropriate owner's manual and included diagrams should be referenced. As an authentic replacement part, this purge bulb is suitable for use on several different models of small engine power equipment such as string trimmers, leaf blowers, and edgers manufactured by Husqvarna, Craftsman, WeedEater, and Poulan. This is a genuine part made of high-quality, durable, non-corrosive materials and is sold individually.

This is a throttle housing designed to go around the throttle cable, trigger, and wire to keep all of those components secure and protected. It's made of durable plastic but wear and tear or impact can damage or break the throttle housing.It's easy to determine with visual inspection if the throttle housing needs to be replaced. A pair of work gloves and an Allen wrench will be needed to complete the repair. The process involves taking out a set of four screws that hold the old throttle housing. Take it off of the equipment and install the new one using the same screws. Once the new housing is placed, the equipment can be used as normal.This is a genuine OEM replacement part that is directly sourced from the manufacturer. It is sold as an individual component. The throttle housing is made for use with string trimmers and pole pruners manufactured by Poulan, Poulan Pro, and Craftsman. This part is sold individually. This part is sold individually.

The handle assist is the handle that is held to steer and control the machine during the trimming process. As the primary touchpoint, the handle has to provide enough comfort while assisting with the machine's function. This handle is designed to be gloves-friendly with a surface rough enough to provide security against slip. Use this as a replacement for a broken, loose, or worn handle. Remember always to hold the handle firmly while operating. This part is designed for use on trimmers or weed cutters made by Craftsman, Weed Eater, Poulan, or Poulan Pro. This is a genuine OEM replacement handle that will provide extra control and less hand fatigue. It is sold individually.

This replacement part is an upper shaft and is intended for use in a variety of lawn equipment. This is a genuine replacement part made by Husqvarna. This upper shaft is typically found in hedge trimmers and is an important part to this appliance. This part is able to connect the power source from the top of the appliance to the trimmer head at the bottom so that the drive mechanisms is activated. A new upper shaft might be needed if the user is unable to control the mechanisms at the bottom of the trimmer. It is possible that the upper shaft might need to be replaced after years of normal wear and tear. Be sure the equipment is completely powered down and cooled off before attempting to repair an appliance. For more detailed instructions on how to install this specific part, see the owner's manual. This is an OEM part sourced directly from the manufacturer. It is sold individually. This replacement part is compatible with different types of lawn equipment made by Husqvarna.

The lower shaft replacement is used for lawn and garden equipment such as trimmers, gas trimmers, and pruners. The shaft is the part that will hold the spool used on these types of equipment. It also connects to the upper shaft.Some of the common problems with the lower drive shaft include worn drive shaft ends, worn bushing, breaks along the metal, or damage to the outer tube. Owners should replace the lower shaft before they use the machine. Continuing to use a trimmer with a broken lower shaft is dangerous and could result in injury or more damage to the machine. The replacement of the lower shaft is relatively simple and will require only a few tools.The replacement part works with certain models of trimmer and pruner from Husqvarna, Weed Eater, and Poulan. This is a genuine OEM replacement part sourced from the manufacturer. The kit is sold individually.

This shield kit is a genuine Husqvarna replacement part for a line trimmers and pole saws. The shield kit, also known as a guard, is a safety precaution to protect the engine from damage and to protect the appliance user from flying debris. The shield also manages the amount of string trimmer line that is spooled out. The shield kit of a line trimmer or pole saw might have to be replaced if there is significant damage to the exterior. While shield kits for line trimmers and pole saws are designed to be durable, the exterior can be gradually worn away by collisions with flying debris and small stones, causing warping and erosion to the plastic material. If the shield kit is damaged, it must be removed and replaced immediately, as it is important for safe use of the appliance. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This shield kit is compatible with the following brands: Husqvarna, Weed Eater, Craftsman, and Poulan. This part sold individually.