Need Help?
Call or text
Show parts
Usually ships within 4 - 14 days
This replacement part is an engine, and it is intended for use in different types of lawn equipment. This is a genuine replacement part made by MTD. This is a complete engine and is found in many different types of lawn mowers. The engine is arguable the most important part in and machine as it allows the entire appliance to operate. In many cases, the appliance is out of commission if the engine does not work.A new engine might be needed if the current one is not starting, or stops during use. If the user notices sounds or unfamiliar noises coming from inside the engine it might be time to replace it. There are many things that could be wrong inside the engine, be sure to check more specific parts to ensure that the entire engine needs to be replaced rather than only one smaller part. This is a genuine OEM part sourced directly from the manufacturer. This engine is sold individually.
This part is a replacement lock plate. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. This part is intended for use as a replacement for a broken or defective lock plate on snowblowers. This lock plate works by locking the auger handle securely into position when the user is adjusting the snowblower chute. Wear work gloves to protect the hands and check that equipment is powered off and cooled down before starting the repair process. Proper tools may be required to install this part. For more accurate information on how and where to install this lock plate, the appropriate owner's manual and equipment diagrams should be referenced. This lock plate is a genuine OEM part made of durable materials and is sold individually. It is suitable for use with snowblowers that have been manufactured by MTD, Yard Machines, Cub Cadet, Yard Man, Husky, and Troy-Bilt.
This is a gasket kit that contains a variety of parts utilized in many kinds of lawn and garden equipment. Each of the parts in the kit is created to seal two surfaces inside the equipment. The components in the kit include a carburetor insulator plate, a carburetor gasket, a carburetor insulator gasket, two carburetor gasket plates, an exhaust pipe gasket, a valve cover gasket, and an oil drain plug washer. If a lawn and garden tool is leaking fuel, air, or oil, these parts can be used to replace the faulty component.A socket wrench or small monkey wrench and a screwdriver will be needed to replace any parts included with the gasket kit. Make sure the lawn equipment is on a flat surface and the spark plug wire has been disconnected. Disassemble any needed components to reach the gasket or other part that needs to be replaced. Put in the new component and reassemble before use.This is an authentic OEM replacement part that is directly sourced from the manufacturer. It is sold as an individual kit. The external gasket kit is designed to be used with snowblowers manufactured by Yard-Man, Huskee, MTD, Yard Machines, Troy-Bilt, Cub Cadet, and Craftsman.
This replacement part is a pivot rod and is intended for use in a variety of lawn equipment. This is a genuine replacement part made by MTD. The pivot rod is present in many types of lawn mowers and is what connects the lift handle to the blade shaft. This allows the user to pivot the blade of the machine when the handle is moved.A new pivot rod might be needed if the current one is damaged or broken in any way. If the user is unable to control the blade movements by using the pivot rod, it is likely damaged or malfunctioning. It is possible for the pivot rod might need to be replaced after years of normal wear and tear. Be sure the equipment is completely powered down and cooled off before attempting to repair an appliance. For more detailed instructions on how to install this specific part, see the owner's manual.This is an OEM part sourced directly from the manufacturer. It is sold individually. This replacement part is compatible with different types of lawn equipment made by MTD.
This part is discontinued by the manufacturer and is no longer available for purchase.
This replacement part is a cylinder head assembly. The cylinder head assembly covers the engine head cylinder and houses the cylinder valves. Over time, the cylinder head assembly can become damaged due to excessive wear and tear. If the engine is no longer running as efficiently as it once did, the cylinder head assembly might need to be replaced. Luckily, this is a fairly simple repair.Before beginning, make sure the engine of the mower has cooled. Once cool, begin by lifting up the hood or engine cover and detach it. Remove the air filter cover. Lift out the air filter. Using a three-eighths socket or wrench remove the blower housing mounting bolts. Detach the oil drain tube and lift off the blower housing. Unthread the bolts that secure the intake manifold and detach the breather tube. Set the carburetor assembly aside. Then unthread the spark plug. Remove the mounting bracket and unthread the exhaust manifold bolts. Pull the manifold free of the muffler. Unthread the valve cover mounting bolts. Pry the cover off with a putty knife and be prepared for some oil to spill. Once the cover is off use the three-eights inch socket wrench to remove the old cylinder head mounting bolts. Pull the old cylinder assembly out of its place and replace it with the new assembly.This genuine OEM part is compatible with MTD brand lawnmowers.
This socket screw is a genuine MTD part, sold individually. This socket screw can be used as a replacement part in a lawn mower or a snowblower. The purpose of the socket screw in a lawn mower or a snowblower is to fasten components together.The socket screw is a small part and might be misplaced or lost within the typical lifespan of a lawn mower or snowblower. If the socket screw is missing, it should be replaced by this genuine OEM replacement part. The socket screw can also be subject to damage in the form of stripping over long-term use as a result of general wear and tear or directly the result of an accident. If this occurs, the screw should be immediately removed and replaced.This component is a genuine OEM replacement part sourced directly from the manufacturer. It is sold individually. This socket screw is compatible with the following outdoor appliance brands: MTD, Craftsman, Cub Cadet, Troy-Bilt, Yard Machines, Huskee, and Yard Man.
This lower chute is a quality replacement part that is used on several models of snowblowers. It is made of high-quality plastic for durability and is placed so it can direct snow in a certain direction when it leaves a snowblower. Over time and with regular use, this part can become damaged. If this occurs, it will need to be replaced so the discharged snow ends up in the right location.When replacing the lower chute, a wrench and work gloves will be needed. The snowblower should be placed on a flat surface, and the spark plug wire needs to be disconnected. The gearbox and the lower chute will need to be removed before the new replacement part can be installed. Line up the chute and install it used the cotter pin and flange lock nut. Replace all the components before using the snowblower.This is an authentic OEM replacement part that is sourced directly from the manufacturer. It is sold on an individual basis. The lower chute is used with snowblowers manufactured by Craftsman, Cub Cadet, Huskee, MTD, Troy-Bilt, Yard Machines, and Yard-Man.
This handle grip part is used on many kinds of lawn and garden equipment that is pushed or otherwise moved around a yard. The handle grips are made out of flexible rubber and are used on the two handles. The purpose of the handle grip is to offer a more secure grip on the power tool and lessen the feel of vibrations.Over time, one or both of the handle grips can start to experience wear. Sometimes, the grips will become damaged or broken. If the grips are very damaged, they may come off of the machinery. There is no need to use tools to replace the handle grip on yard equipment. The old part just needs to be removed from the tool so that the new component can be slipped on. Wear a pair of work gloves to make the process easier.This is a genuine OEM handle grip replacement that is sourced directly from the manufacturer. It is sold individually. The part is compatible with lawnmowers, snowblowers, tillers, and chainsaws created by MasterCut, Yard-Man, Bolens, Montgomery Wards, Huskee, MTD, Yard Machines, Murray, Troy-Bilt, Ryobi, Cub Cadet, and Craftsman.
This carriage bolt is a genuine MTD part, sold individually. This carriage bolt can be used as a replacement part in lawnmowers, snowblowers, tillers, and edgers. The purpose of the carriage bolt for one of these outdoor appliances is to work in conjunction with a nut to affix two metal components to one another or one metal component to another wood component.The carriage bolt in an outdoor appliance might have to be completely replaced if it cannot affix two or more components together. This could occur if the carriage bolt has been punctured, dented, cracked, warped, or eroded to the point that it loses its functionality. If this occurs, the carriage bolt should be removed and replaced by this genuine OEM replacement part.Sourced directly from the manufacturer, this component is a genuine replacement part that is sold individually. This carriage bolt is compatible with the following outdoor appliance brands: MTD, Craftsman, Cub Cadet, Ryobi, Troy-Bilt, Yard Machines, Huskee, Bolens, Yard-Man, and MasterCut.
This replacement part is a handle panel assembly. This is a genuine replacement part made by MTD. This part is commonly found in certain types of lawn mowers and works as a control panel so that the user may operate the machine to their desired preferences. A new handle panel assembly might be needed if the current one is missing or damaged in any way. If the panel has become damaged by flying debris or an isolated incident, it is recommended that it be replaced. If the part is no longer able to stay attached to the machine, it is possible that it's been stripped down over time. This is not uncommon for parts like these.This part is sold individually and is sourced directly from the manufacturer. This handle panel assembly is a genuine OEM replacement part to ensure proper fit.
This replacement part is a lens. It is a genuine replacement part made by MTD. This type of part is typically found in snow blowers and is used to protect the light bulb. This lens allows the user to see the area in front of them while working in times that are not as well lit. A new lens might be needed if the current one is damaged or missing in any way. This can be due to normal wear and tear after many years of use. If the lens is damaged it can cause harm to the light bulb and it is recommended that it be replaced as soon as possible. This deck shell is a genuine OEM replacement part to ensure long-lasting use. This part is sold individually and is sourced directly from the manufacturer to ensure proper fit.
This is a seven-inch cable tie that is used with different types of lawn and garden equipment. It is most commonly used to secure the cable onto the handle of the lawnmower or tiller so it is secure. The cable tie is made of durable plastic but can be damaged or break. When this happens, the tie will need to be replaced to ensure the cable stays on the handle.If the cable tie needs to be replaced, no tools are needed. In the situation where other parts need to be replaced at the same time, a basic set of tools and a pair of work gloves may be required. Turn off the yard equipment and place it on a stable surface before replacing the broken cable tie. The old tie can be removed so the new one can be installed before further use.This cable tie is an authentic OEM replacement part that is directly sourced from the manufacturer. This product is sold individually. The component is designed to be compatible with lawnmowers, lawn tractors, tillers, and snowblowers manufactured by MTD, Troy-Bilt, Yard-Man, and Yard Machines.
A flange lock nut, also known as a flange lock or a lock nut, is created to be used in various types of lawn and garden equipment. This flange lock nut holds other parts in place and, when properly threaded, will resist loosening. Over time, a flange lock nut may begin to weaken and may become loose or break. If it appears to be broken or weak, a replacement is required. Flange locks can be adjusted and uninstalled after use. When replacement is required, you may need a socket set, screwdriver, hacksaw, and butane torch. The socket wrench will loosen the bolt it is connected to, while the torch is used to heat the lock nut. A socket wrench may remove the nut, but sometimes cutting it with a hacksaw is required. This flange lock nut is a genuine OEM component directly from the manufacturer and comes in an individual unit. It is made of metal, a gold color, and can be found in various areas of lawn equipment. It works with lawnmowers, trimmers, snowblowers, cultivators, tillers, and leaf blowers by Poulan, MTD, Toro, Cub Cadet, Murray, Troy-Bilt, Bolens, Yard Machines, Craftsman, and Yard-Man.
This genuine MTD speed selector cable attaches the speed control lever to the snowblower's ground drive system to regulate and maintain the speed of the snowblower.Though speed selector cables are highly durable, they can be subject to damage as a result of exposure to inclement weather, impact upon collision, and general decline. Signs of a damaged speed selector cable can include malfunctioning regulation of speed, an overheating engine, or black smoke rising from the engine. If any of these symptoms occur, the speed selector cable should be checked and replaced immediately, as the snowblower cannot function properly without it. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This speed selector cable is compatible with the following brands: MTD, Troy-Bilt, Cub Cadet, Yard Machines, and Craftsman. Part sold individually.
This is a versatile screw designed with flanged hex head and double-lead threads. It is a high-low self-tapping screw with one thread that is high and the other low for easier penetration. The twin threads also reduce the amount of material displaced when the screw is driven into the material. This type of screw also creates a firmer grip. This screw can also be used to secure a newly installed front cover or grill. This part is available as an individual replacement part. It is a genuine OEM part for use with specific models of snow throwers, lawn tractors, electric mowers, chippers, and log splitters from Bolens, Cub Cadet, Craftsman, Poulan, Ryobi, Toro, MTD, Troy-Bilt, Yard Machines, and Yard-Man.
This screw is a genuine MTD part, sold individually. This screw can be used as a replacement part in a snowblower. The purpose of a screw in a snowblower is to fasten one or more components through the process of rotating the screw so that it pierces into the component in order to fasten it in its stable placement while the appliance is in use.The screw in a snowblower might have to be replaced if the screw is lost, misplaced, or stripped away from general wear and tear with long-term use. The screw can be easily lost or misplaced as it is a small component that can disappear from the internal mechanisms of the appliance without necessarily changing anything; the screw can also be subject to many forms of damage which can necessitate its removal and replacement with this genuine OEM replacement part.This component is a genuine OEM replacement part sourced directly from the manufacturer. It is sold individually. This screw is compatible with the following outdoor appliance brands: MTD, Craftsman, Cub Cadet, Troy-Bilt, Yard Machines, Huskee, and Yard Man.
A cotter pin, also known as a hitch pin, is used to secure pins and shafts in place. Meant for snowblowers, riding lawnmowers, and lawn tractors, this bow-tie shaped cotter pin has a double-end design making it easy to pull or push through either side of a pre-drilled hole. This pin snaps into a locked position without tension, keeping it secure during operation. Designed for lawn and garden maintenance equipment, this part ensures secure fastening. If the power equipment is used frequently, cotter pins may have to be replaced regularly so it would be practical to keep extra bow tie cotter pins on hand. It is highly recommended that work gloves be worn during the installation of this part. This part is compatible with Craftsman, Cub Cadet, Troy-Bilt, Murray, Yard Machines, MTD, Huskee, Bolens, Yard-Man, and MasterCut brands of lawn mower, snowblower, and log splitters. This is a genuine OEM replacement part that is sold individually.
This is a carriage bolt, which is found on lawnmowers, snowblowers, and many other types of lawn and garden equipment. The carriage bolt is made of metal and the location will vary based on the model of the tool. The carriage bolt is used to fasten together two components on lawn and garden equipment. It can become damaged, break, or stripped and will need to be replaced.If the carriage bolt is broken, stripped, or has damage, a wrench will be needed to replace it. Make sure that the spark plug wire has been disconnected and the tool is turned off before you begin. Use the wrench to remove the carriage bolt before installing the new part in the same location. Replace any additional disassembled components removed to gain access to the bolt before using the tool.This carriage bolt is sold as an individual component. It is a genuine OEM replacement part that is sourced directly from the manufacturer. The bolt is designed to work with lawnmowers, chainsaws, snowblowers, tillers, and leaf blowers manufactured by Yard-Man, Bolens, Montgomery Wards, Huskee, MTD, Yard Machines, Husky, Troy-Bilt, Ryobi, Cub Cadet, and Craftsman.
This part is a replacement control lever. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. This part's intended use is to replace a broken or defective control lever in snow blowers.This control lever is necessary for controlling the power and enabling the user to drive the auger. It attaches to the upper handle and will require replacement if detached, broken, or in any way ineffective. T's important when working on or near an engine to make sure the equipment is powered off and completely cooled down before starting any repairs. For more accurate information on how and where to install this control lever, reference the appropriate owner's manual and specific equipment diagrams.This is an authentic OEM replacement part made of high-quality materials. This control lever can be used with different models of snow blowers that have been manufactured by MTD, Craftsman, Troy-Bilt, and other brands. Part sold individually.
A star knob connects the upper and lower handles on an outdoor appliance, and if removed, the upper and lower handles are quick-released. This part is made of black heavy-duty black plastic, and the threads are made of steel. Over time, the threading can become worn out, making the connection loose, and causing the two handles to no longer stay in place. Star knobs are a straightforward repair that can be done in a matter of minutes. Just unscrew the original, damaged knob and screw in the new knob. The knob is designed to be unscrewed by hand, so there is no need for additional tools to make this repair. This genuine OEM replacement part is designed for a variety of outdoor appliances, including lawnmowers, edgers, chippers, tractors, trimmers, and cultivators. This star knob is compatible with Yard Machines, Yard-Man, Cub Cadet, Bolens, Craftsmen, and Ryobi products. This part ships individually.
A flange nut's unique wide flange design distributes the nut's pressure over the part it is securing. In return, it creates an even fastening surface, which reduces part damage and nut loosening. This one-piece all-metal fastener has a lock nut version that features a protruding circular flange. This drastically increases bearing surface, compatibility either for irregular or oversized holes, and surface tension reduction. Flange lock nuts are the preferred type of fastener for many lawnmower models because it can provide better fastening than regular screws, which are known to loosen under extreme vibration. However, it’s important to know that flange lock nuts are susceptible to wear and tear due to constant vibration exposure. It is essential to replace the broken flange lock nut immediately to prevent serious damage to the lawnmower. The MTD 712-04063 Flange Lock Nut OEM replacement can be used with Craftsman, White Outdoor, Yard Machines, MTD, or Columbia lawnmowers. It is a genuine or OEM MTD replacement part that measures 5/16-18. It is threaded and requires the use of a wrench. This replacement flange lock nut is sold individually. An MTD bolt carriage may also be needed and is sold separately.
This chute tilt is also called a chute tilt cable guide or a bracket. It is a genuine MTD part and it is a replacement part for various makes and models of snowblowers. On snowblowers, the chute tilt attaches the chute control lever to the chute control cable and guides the cable while the lever moves.If the chute tilt is damaged, the snowblower may not be able to perform its function. Some disassembly is required to make this repair. Be sure to allow the engine to cool completely, empty the fuel tank, and disconnect the spark plug to prevent the engine from powering on. Always wear protective gloves as well. This hub cap is a genuine OEM part that is sourced directly from the manufacturer. It is sold individually. It is made to be compatible with equipment manufactured by Cub Cadet, Yard Machines, Yard-Man, Troy-Bilt, Craftsman, Huskee, and MTD.
This clevis pin is a genuine MTD part, sold individually. This clevis pin can be used as a replacement part in a snowblower. The purpose of the clevis pin in a snowblower is to serve as a u-shaped fastening component used in the place of a bolt and rivet to secure various parts within the internal mechanisms of the appliance.The clevis pin in a lawnmower might have to be replaced if the clevis pin can no longer hold one or more components in place within the lawnmower. The clevis pin could suffer damage from general wear and tear with long-term use, due to collision with a hard object, or from exposure to the elements. If any damage occurs that reduces the functionality of the clevis pin, it should be removed and replaced by this genuine OEM replacement part.This component is a genuine OEM replacement part, sourced directly from the manufacturer. It is sold individually. This clevis pin is compatible with the following outdoor appliance brands: MTD, Craftsman, Cub Cadet, Troy-Bilt, Yard Machines, Huskee, and Yard-Man.
The Hex Head Self-Tapping Screw is an OEM part for MTD outdoor power equipment. This screw is designed to securely fasten components of your equipment, providing reliable and durable connections. The thread size is 5/16 inches for major diameter, with 18 threads. The screw is 3/4 inches long and has a hexagonal or six-sided head.
Over time, the Hex Head Self-Tapping Screw can become damaged due to corrosion, stripping of the threads, or wear from frequent tightening and loosening. This can compromise the integrity of the connections and potentially lead to equipment malfunction.
Symptoms of a bad Hex Head Self-Tapping Screw include:
This OEM replacement part is designed for use with various models of MTD outdoor power equipment.
This part is a replacement handle. This part can be used to replace a defective or broken handle in a variety of snow blower models. The handle allows the user to properly and safely control and maneuver the equipment. This part may become detached, dented, bent, or otherwise damaged over time, requiring replacement. When working on or near an engine, it is important to ensure that it is powered off and completely cool before beginning any repairs.As an authentic replacement part from MTD, this handle is suitable for use on snow blowers that have been manufactured by MTD, Craftsman, Troy-Bilt, and other brands. This is a genuine OEM part made of high-quality, durable materials and is sold individually.