Parts for Kenmore 795.79433213 (79579433213, 795 79433213): Ice Maker Part Parts

This replacement screw secures specified panels or components inside your appliance. Refreshing worn or missing hardware helps restore a tight fit, reduce rattling, and keep assemblies properly aligned for reliable performance.

• Provides secure fastening for brackets, panels, or internal assemblies
• Replaces stripped, rusted, or lost hardware
• Helps reduce vibration and rattling noises
• Symptoms include loose panels, shifting components, or a screw that won't tighten

• Disconnect power and allow any hot surfaces to cool before servicing
• Wear cut-resistant gloves and eye protection
• Match length and thread to the original; replace like-for-like
• Start threads by hand to avoid cross-threading; do not overtighten

This guide tube is a small routing sleeve that supports and protects a rod, shaft, cable, or line inside your appliance. It keeps the path straight to reduce friction, noise, and premature wear.

• Guides and supports a rod/shaft/cable/tube through the chassis
• Maintains alignment for smooth movement or flow
• Helps prevent chafing, kinks, and vibration-related damage
• Typical failure signs: scraping or rattling noises, binding/misalignment, or visible cracks/deformation

• Disconnect power; turn off water or gas before servicing
• Refer to your model's parts diagram for routing and mounting points
• Reuse original screws/clips unless damaged
• Route exactly like the original; avoid pinches/kinks and verify clearances before restoring power

This refrigerator ice maker assembly restores automatic ice production. It manages the fill, freeze, and harvest cycles so your freezer reliably makes and releases ice cubes into the bin.

• Produces and harvests ice cubes automatically
• Controls water fill and the freeze/eject timing for each cycle
• Pauses production when the bin is full
• Common fixes: no ice production, very low ice output, unit stuck mid-cycle, cubes not ejecting, or loud clicking from the ice maker module

• Unplug the refrigerator and turn off the water supply before servicing
• Match and seat the wire connector fully; do not force pins
• Reuse any original mounting brackets, covers, or ice-level arm if required by your model
• Align the fill tube with the ice maker fill cup; restore power and allow up to 24 hours for normal ice production

This holder assembly is a structural mounting piece that supports and secures an internal component in your appliance. Replacing a cracked or worn bracket helps restore proper alignment and keeps parts stable during everyday use.

• Provides a rigid mounting point for the attached component
• Keeps parts aligned to reduce movement and vibration
• Helps prevent rattling or noise from loose mounts
• Common signs of failure: visible cracks/broken tabs, looseness, or parts that won't stay seated

• Disconnect power and, if applicable, turn off the water supply before service
• Note the orientation of the original part to match fitment
• Reuse existing mounting screws or hardware unless the manufacturer specifies otherwise
• Do not overtighten fasteners; the secured component is fully seated and stable

Note: 90 degree elbow coupler (Fits 1/4" diameter tubing on each end) For 5/16" elbow connector, order part# 4932JA3009B.

The Water Line Union is an OEM part for LG refrigerators. This component connects sections of the water line, ensuring a secure and leak-free passage of water to the refrigerator's icemaker and water dispenser. It is an elbow tube union connector, which connects two tubes at a 90-degree angle.

Causes of a bad water line union can include wear and tear from frequent use, damage from high water pressure, or deterioration due to mineral buildup and age. A compromised union can lead to water leaks and disruption in the water supply.

Symptoms of a bad Water Line Union include:

• Water leaks around the connection points
• Reduced water flow to the icemaker or water dispenser
• Puddles or moisture near the refrigerator
• Unusual noises from the water line

This OEM LG part is also compatible with Sears/Kenmore.

This replacement injection tube routes water through the refrigerator's supply system to the ice maker or dispenser, as designed for your model. Replacing a cracked or kinked tube restores proper flow and helps prevent leaks.

• Channels water from the inlet circuit to its destination component (ice maker or dispenser, per design)
• Helps maintain a sealed path for clean, reliable water delivery
• Common symptoms: water leaking inside/behind the refrigerator
• Dispenser has slow/no flow
• Ice maker not filling or producing small/hollow ice; visible cracks, kinks, or brittle tubing

• Unplug the refrigerator and shut off the household water supply before servicing
• Note the original routing and connector types; transfer any reusable fittings or clamps from the old tube
• Insert the tube fully into existing connectors or onto barbed fittings and secure with the original clips/clamps
• Restore water, check all joints for leaks, then power on and test the dispenser/ice fill

This water inlet valve controls water flow into the appliance, restoring water delivery for the dispenser and ice system when the valve is faulty. Replaces a worn or leaking valve to help recover normal water operation. What it does:

• Opens and closes to allow water into the appliance when the dispenser or ice maker calls for water
• Stops water flow when the dispenser/ice maker is idle to prevent leaks
• Commonly linked to no water at the dispenser, no ice production, or intermittent water flow
• May leak or fail electrically if solenoids or seals wear out

• One complete water inlet valve assembly

• Disconnect power and shut off the water supply before starting any repair
• Handle water lines carefully; replace any damaged supply tubing or gaskets to prevent leaks
• Tighten fittings securely and check for leaks after restoring water and power

This water inlet valve assembly controls the flow of water from your home's supply into the refrigerator for the dispenser and ice maker. Replacing a failed valve restores reliable filling and helps prevent leaks, no-dispense, and no-ice issues.

• Regulates and routes water to the ice maker and dispenser when energized by the control system
• Resolves: no water from dispenser, no ice production, slow fill, or intermittent dispensing
• Leaks or drips from the rear valve area or water line connections
• Continuous water flow or ice maker overfill caused by a valve stuck open

• Disconnect power and shut off the water supply before servicing
• Pull the refrigerator forward to access the rear; have a towel or pan ready for residual water
• Transfer each wire connector and water tube to the matching port on the new valve; ensure all fittings lock fully
• Restore water and power, then check connections for leaks and test dispenser/ice fill