Parts for Electrolux EI23CS35KW2: 15 - Ice & Water Dispenser Parts

Water supply tube that routes water through your refrigerator to the ice maker and dispenser. Replace if cracked, leaking, or damaged during moving.

Control module cover shields electronic board from moisture and dust. Protects dispenser touchpad controls from damage. Simple snap-on installation.

The Dispenser Module is an OEM part for Frigidaire refrigerators. This part controls and operates the water and ice dispenser functions.

Causes of a bad Dispenser Module can include electrical malfunctions, physical damage from impact or moisture, or general wear and tear over time.

Symptoms of a bad Dispenser Module include:

• Failure of the water or ice dispenser to operate
• Inconsistent or partial dispensing of water or ice
• Leaks or drips from the dispenser area
• Error codes or indicator lights related to the dispenser

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Replacement nameplate for your refrigerator. Installs on the exterior to display model information. Needed when original is faded, damaged, or missing.

Fix constant beeping, CE error codes, or unresponsive controls with this refrigerator switch board. Routes button commands to your control system. DIY repair.

This replacement screw secures appliance panels, brackets, and internal components. It restores a tight, rattle-free fit and proper alignment when an original fastener is missing, stripped, or corroded.

• Fastens metal or plastic parts to the cabinet/frame
• Helps maintain alignment and reduce vibration or rattling
• Direct replacement for lost, damaged, or rusted hardware
• Keeps covers and brackets safely in place

• Disconnect power before servicing; for gas appliances, also shut off gas supply
• Match one-for-one with the original screw; verify length/type before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver bit to prevent stripping the screw head

This liner sump is the molded drain pan that collects and channels defrost and condensation water inside the freezer/refrigerator cabinet, helping prevent leaks and directing moisture to the drain system. What it does:

• Collects defrost and condensation water from the evaporator area
• Channels water to the cabinet drain to avoid pooling and potential leaks
• Helps keep the freezer/refrigerator interior dry and reduces ice build-up around the evaporator
• Compatible with OEM mounting points and drainage pathways when correctly installed

• One liner sump

• Disconnect power to the appliance before beginning service
• Access may require removing interior panels or the evaporator cover; follow factory service instructions
• Handle carefully to avoid damage to the molded drain passages; ensure proper seating and seal when reinstalling
• After installation, restore power and run a short defrost or water test to ensure proper drainage

This replacement screw secures appliance panels, brackets, and internal components. It restores a tight, rattle-free fit and proper alignment when an original fastener is missing, stripped, or corroded.

• Fastens metal or plastic parts to the cabinet/frame
• Helps maintain alignment and reduce vibration or rattling
• Direct replacement for lost, damaged, or rusted hardware
• Keeps covers and brackets safely in place

• Disconnect power before servicing; for gas appliances, also shut off gas supply
• Match one-for-one with the original screw; verify length/type before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver bit to prevent stripping the screw head

Water supply tube for side-by-side refrigerators. Connects water line to dispenser or ice maker. Replace if cracked, leaking, or damaged.

Fix ice buildup and frozen water dispenser issues with this dispenser heater kit. Prevents frost clogging in the chute and valve area. Moderate DIY repair.

Routes water from supply line to dispenser and icemaker. Replace if tube is cracked, leaking, kinked, or damaged to restore proper water flow.

Replaces cracked, leaking, or melted ice maker fill tube that carries water from the supply line to the ice mold. Installs in the freezer compartment.