Ikea Range / Cooktop / Oven Parts

This door hinge supports and guides the appliance door so it opens and closes smoothly and stays aligned with the latch and gasket. Replacing a worn hinge restores proper fit and closing action to reduce rubbing and poor sealing.

• Provides the pivot point and supports the door's weight during operation
• Maintains alignment for an even gap and consistent seal
• Helps correct sagging, scraping, or a door that won't close flush
• Common signs of wear: bent/cracked hinge, squeaking or popping, misalignment

• Disconnect power before servicing and support the door to prevent strain or damage
• Remove mounting fasteners; transfer any reusable screws, spacers, or covers from the old hinge
• Install and snug fasteners, then check door alignment and closure; adjust as needed
• Open and close the door several times to verify smooth operation and recheck fasteners

This oven door hinge restores smooth, controlled door movement and a proper seal. Worn hinges can cause a sagging door, poor closure, or binding—replacing the hinge helps maintain safe operation and consistent cooking performance.

• Supports the oven door with a spring mechanism for controlled opening and closing
• Helps pull the door tight against the gasket for an effective seal when closed
• Works with the opposite hinge to keep the door aligned and stable
• Common symptoms include door not closing fully, sagging or dropping, hard-to-open/close action, or heat escaping around the door

• Disconnect power and allow the oven to cool completely before servicing
• Remove the door following your model's instructions; engage hinge locks or use retaining pins if provided
• Replace the hinge in the same orientation; ensure hinge arms are fully seated in the receivers
• Reinstall the door and verify smooth motion and a complete seal

This oven door hinge restores smooth, controlled movement so the door opens easily and closes fully for a reliable seal. Replacing a worn hinge helps reduce heat loss and supports consistent cooking performance and safe operation.

• Provides the pivot and spring-assisted action for opening and closing the oven door
• Helps pull the door closed and hold it at intended stop positions
• Maintains even gasket contact to keep heat inside the cavity
• Common symptoms of a failing hinge: door won't close fully or sit flush, drops or slams open, binds or pops when moving, or shows an uneven gap

• Disconnect power and allow the oven to cool completely before servicing
• Support the door; open to the removal position and release hinge locks, then lift the door off
• Use caution—hinge springs are under tension; wear hand and eye protection
• Install in the same orientation and verify door alignment and smooth operation after reassembly

This spark module supplies the high-voltage pulses that ignite the surface burners on a gas cooktop or range. Replacing a failing module helps restore consistent clicking and spark so burners light promptly and reliably.

• Supplies high-voltage to up to five surface igniters (5+0 configuration)
• Sends spark when a burner control is turned to Lite
• Failure symptoms can include no spark on all or multiple burners
• May also cause intermittent/weak spark or continuous clicking

• Disconnect power and shut off gas before servicing
• Note wire locations; move one connector at a time to matching terminals
• Mount securely in the original position and ensure proper grounding
• After replacement, if only one burner won't ignite, inspect that burner's switch and igniter

This is a smoothtop assembly intended for use with ranges by major manufacturers. This component is located on top of the stove and protects the wiring and heating elements on the interior. The smoothtop assembly is made of strong glass. This part can become damaged and may be unsafe for use. If this happens, the smoothtop assembly will need to be replaced.A set of basic tools will be needed to replace this part. Work gloves can also be useful for preventing injuries from broken glass. First, turn off the range. Unplug it from the wall and make sure it is cool to the touch. Open the oven to remove the screws that hold the smoothtop assembly in place. Pick it up and disconnect the heating elements and wires. Next, install the new smoothtop assembly and hook back up the internal components. Plug in the appliance before use.This is an authentic OEM replacement component that is sourced directly from the manufacturer. It is sold on an individual basis. The smoothtop assembly is made to be used with ranges, ovens, and stoves created by Ikea, Frigidaire, and Crosley.

The Surface Burner Orifice Holder is an OEM part specially designed for Whirlpool gas ranges and cooktops. This part holds and positions the burner orifice above the surface burner, facilitating the mixture of gas and air required for combustion. 

Symptoms of a bad orifice holder include:

• Yellow or incomplete burner flames  
• Flames not remaining centered on the burner surface
• Burners that will not light or stay lit
• Gas leaks detected around the burner area

This is also compatible with Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, and Roper gas ranges and cooktops. 

This black glass smooth top is the flat cooking surface that covers and protects the range's heating elements, restoring a clean, level work area for cookware and improving the cooktop's appearance. What it does:

• Replaces cracked, chipped or shattered glass to restore a safe cooking surface
• Provides a smooth, easy-to-clean flat surface for pots and pans
• Protects internal burners and heating elements from spills and debris
• Helps cookware sit level for even contact with heating elements

• Disconnect power to the appliance before starting; handle glass with care and wear cut-resistant gloves
• Removal often requires lifting out burner components and removing trim; keep fasteners and brackets for reassembly
• Inspect and reuse existing gaskets or mounting hardware unless damaged

This orifice controls the flow of gas to a burner, helping produce the correct flame for safe, consistent cooking and baking. It replaces a worn or damaged gas metering jet to restore proper burner performance. What it does:

• Meter gas flow to a specific burner for correct flame size and heat output
• Helps maintain steady ignition and even cooking when functioning properly
• Commonly used when a burner shows a weak, uneven, or no flame
• Also replaces corroded or clogged jets that restrict gas flow

• Turn off the gas supply and power to the appliance before beginning work
• Use appropriate tools and avoid overtightening; match the replacement to the original part number
• Inspect for debris or corrosion and clean mating surfaces before installation

This smooth top cooktop glass assembly replaces a cracked or damaged cooktop surface to restore a flat, easy-to-clean cooking area and proper cookware contact. It fits select electric range models and restores appearance and function. What it does:

• Covers and protects the range's heating elements while providing a smooth cooking surface
• Restores even cookware contact for efficient heating when the underlying elements are working
• Helps prevent debris from falling into the range cavity and simplifies cleanup
• Commonly used when the glass is cracked, chipped, or heavily scratched

• Handle with care; glass can be heavy and break if dropped — use gloves and eye protection
• Verify power is disconnected at the breaker before starting any work
• Installation usually requires removing the range top trim and disconnecting wiring to access mounting points; follow OEM instructions
• If underlying heating elements or supports are damaged, replace them as needed for safe operation

A surface ignitor that produces the spark needed to light gas burners on compatible ranges and cooktops. Replaces a worn or failed ignitor to restore reliable ignition and consistent burner lighting. What it does

• Creates the spark at the burner to ignite gas when the control is turned on.
• Commonly used when burners click but fail to light or when a specific burner never ignites.
• Works with the cooktop's ignition system to provide consistent, repeatable sparking.
• Fits into the burner assembly and connects to the appliance's existing wiring and mounting.

• One surface ignitor (quantity: 1)

• Disconnect power to the appliance and shut off the gas supply before starting any service.
• Handle the ignitor by the ceramic/insulated areas; avoid touching the tip with bare hands to prevent contamination or damage.
• Confirm correct fit and secure all wiring connections; test ignition on a safe flame setting after reinstalling.

This single replacement control knob restores safe, precise control of your appliance's settings. It fits standard control stems to replace a cracked, worn, or missing knob so you can turn burners or temperature dials smoothly. What it does:

• Replaces a damaged or missing control knob so you can select heat or function settings reliably.
• Provides a secure grip and clear pointer alignment for accurate setting selection.
• Stops slipping or spinning on the control shaft when the original knob is worn.
• Helps eliminate intermittent contact or incomplete turns caused by broken knobs.

• Disconnect power to the appliance before servicing to avoid injury.
• Pull the old knob straight off the control stem; press the new knob onto the stem until fully seated.
• Align the pointer on the knob with the control indicator for correct settings.
• If the knob does not seat properly or the control shaft is damaged, do not force—inspect the shaft and replace damaged components as needed.

This inner door glass is the heat-resistant panel mounted on the inside of the oven door. It restores a clear, secure barrier to help retain heat and visibility when the original glass is cracked, shattered, or stained.

• Forms the inner pane of the oven door to contain heat and allow viewing of food
• Damage can cause heat loss, longer preheat/cook times, and unsafe sharp edges
• Cracked, shattered, or missing glass should be replaced before using the appliance
• Cloudy or permanently stained glass reduces visibility into the oven

• Disconnect power at the breaker and allow the oven to cool completely
• Wear cut-resistant gloves and eye protection; handle glass carefully
• Support or remove the door and work face-down on a padded surface
• Transfer any brackets/clips/insulation as configured; do not overtighten fasteners against the glass

Kit includes 4 pins.