Parts for Ge PHS93EYP2FS: Induction Control Tray Parts

Range blower not venting properly? This centrifugal blower restores proper ventilation. Direct replacement part for select electric range models.

Replacement cooktop glass surface for electric ranges. Restores flat, even finish when original is cracked, chipped, or scratched. Dark gray color.

This lower oven warming element heats the oven's warming/holding compartment so food stays warm until serving. Replaces a damaged or non-heating lower element to restore consistent low-temperature operation. What it does:

• Heats the oven's warming/lower compartment for holding cooked food
• Replaces elements that show visible damage, burn-through, or no heat output
• Helps restore even low-temperature performance when the warmer function fails
• Works with the oven's temperature control and safety circuits to provide steady heat

• One lower oven warming element

• Disconnect power at the breaker before beginning any repair
• Wear gloves; element edges and terminals may be sharp
• Verify proper wiring and secure terminal connections during installation

This induction cooktop element provides targeted heating for compatible induction ranges, replacing a failed or weak cooking zone to restore fast, reliable cooking performance. Designed as a direct-replacement heating element for the specified part number. What it does:

• Heats cookware using induction to generate a hot cooking zone when paired with compatible cookware.
• Restores a non-working or underperforming cooktop zone that no longer responds or heats properly.
• Helps eliminate uneven heating or slow-to-heat symptoms tied to a single induction element.
• Works with the range's control and power system to enable normal cooktop function.

• One induction cooktop element (2500W)

• Disconnect power at the breaker before inspecting or replacing the element to avoid electrical shock.
• Handle the element and glass/ceramic surround carefully to avoid damage; use proper tools and protective gloves.

Element not heating or cooking unevenly? This induction element restores precise temperature control. Common repair for cracked or damaged elements.

The Rear Vent Trim and Gasket Assembly is an OEM part for GE ranges. It seals the rear vent opening of the range, directing hot air and potential gas fumes outside through the exhaust vent during oven use. Without an intact seal provided by the gasket and vent trim, combustion byproducts can enter the kitchen presenting safety and performance issues.

Causes of a bad range rear vent assembly include wear over years of use with high heat cycles, cracking or degradation of sealing materials, or damage from cleaning or impacts around the vent area.

Symptoms of an issue include:

• Foul odors detected in the kitchen during use of the oven
• Inefficient or uneven baking and broiling
• Visible openings or gaps seen around the rear vent perimeter
• Detached, cracked, or missing components

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This is a replacement black screw used to secure interior or exterior appliance components. It provides a discrete, color-matched fastener to restore proper fit and stop rattles or loose panels. What it does

• Fastens trim, panels, brackets or control components where a small black screw is required
• Restores secure mounting to eliminate vibration, rattling or misaligned parts
• Matches finished appliance surfaces for a clean, unobtrusive look
• Simple hardware replacement for small fastener loss or damage

• One black screw

• Disconnect power to the appliance before servicing to avoid shock or injury
• Use the correct screwdriver to seat the screw; avoid overtightening to prevent stripping or cracking surrounding material
• Keep track of small fasteners during disassembly and handle with care
• Replace with the exact part number if the original screw is damaged or the thread/length differs

Hex washer head screw secures oven panels, brackets, and door handles. Replace missing, stripped, or damaged screws to eliminate looseness and rattling.

Replacement mounting screw for electric ranges and wall ovens. Secures components and panels. Order a new screw if yours is stripped, missing, or damaged.

Black. 8-18 AB HXW 3/8

Spacer for electric ranges. Installs to maintain proper clearance between components. Replace if cracked, worn, or missing to restore correct spacing.