Parts for Thermador T36IT71FN/01: Installation Parts

This active carbon filter refreshes the air when your range hood is set to recirculate. Replace a saturated filter to restore effective odor reduction and maintain a more comfortable cooking space. What it does:

• Adsorbs cooking odors in recirculating operation
• Helps maintain fresher indoor air when venting back into the room
• Restores odor-removal performance when the old filter is saturated
• Typical signs it's time to replace: persistent cooking smells or diminished odor reduction

• One activated carbon filter

• Disconnect power to the hood before servicing
• Remove the metal grease filter(s) to access the charcoal filter
• Release the old filter from its clips/bayonet mount and install the new filter in the same orientation until it locks
• Charcoal filters are not washable; replace when saturated

• For hoods configured for recirculation; not used when vented to the outdoors

The Water Filter is an OEM part for Bosch refrigerators. This part removes impurities and contaminants from the water supply to your appliance. This part ensures that the water and ice dispensed by your refrigerator are clean, taste fresh, and are free of common waterborne particles and substances. 

Over time, the water filter can become clogged with sediments and contaminants, reducing its effectiveness and potentially affecting the taste and quality of the water and ice. Regular replacement is essential for maintaining optimal performance.

Symptoms of a bad Water Filter include:

• Unpleasant taste or odor in the water or ice
• Decreased water flow to the dispenser or ice maker
• Visible particulate matter in the water or ice cubes

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This fixture is the replacement mounting component used to secure internal parts and assemblies in place, restoring proper alignment and reducing rattles or movement. It's a direct-fit replacement when the original fixture is cracked or missing. What it does

• Secures and supports nearby panels or internal components to maintain correct alignment.
• Prevents rubbing, vibration noise, and misalignment caused by a broken or missing fixture.
• Helps maintain the appliance's intended fit-and-function of adjacent parts.
• Use when visual damage, looseness, or part migration is observed.

• One fixture component

• Turn power off and disconnect the appliance before beginning any repair.
• Access the location via the appropriate panel or assembly; retain screws and fasteners for reassembly.
• Replace only the damaged fixture and verify adjacent parts are not worn.

This profile stripe is a replacement door trim strip that restores the finished look of the appliance and protects the door edge from chips and wear. It's a direct-fit exterior trim designed to match the original appearance. What it does

• Replaces a worn, cracked, missing, or scratched door trim stripe to restore cosmetic appearance
• Covers the junction between door panels and provides a finished edge
• Helps protect the door edge from everyday dings and moisture at the seam
• Restores proper fit and alignment of visible trim for a factory look

• Use basic hand tools; remove power to the appliance and follow OEM instructions before starting
• Handle trim carefully to avoid marring the finish; clip or adhesive locations may be fragile
• If adhesive is used, allow proper cure time per adhesive manufacturer instructions

Replacement retaining pin that secures appliance components so panels, hinges or linkages stay connected. Use this direct-fit hardware to restore proper alignment and reduce looseness, rattling or separation caused by a missing, bent or worn pin.

• Secures mating parts like hinges, levers or shafts to prevent separation and play
• Common symptom: loose or rattling door/panel or misaligned assembly where the original pin is missing or damaged
• Typical use: keeps pivot points and small assemblies aligned for proper operation
• Metal fastener designed for a simple, local replacement

• Disconnect power (and water, if appliance type requires) before servicing
• Remove any obstructions and note original orientation before removing the old pin
• Use appropriate hand tools; do not force parts—if fit is tight, inspect mating components for damage

This factory trim strip finishes an edge or covers a seam on the appliance. Replacing a worn or missing strip restores a clean appearance and proper fit, and helps keep adjoining parts aligned where designed.

• Provides a finished edge and covers gaps/seams in the specified location
• Helps position or stabilize an adjacent panel or gasket where applicable
• Direct replacement for a cracked, warped, discolored, or missing strip
• Common symptoms: visible gap, loose or rattling panel, misaligned edge, cosmetic damage

• Disconnect power and, if applicable, water supply before servicing
• Remove any related panels/fasteners to access the mounting area; retain hardware for reuse
• Align the new strip to the original footprint and press/secure it using the existing attachment method
• Avoid overbending; ensure proper panel/door alignment and operation after installation