Parts for Ge CVM1790SS1SS: 06 - Interior Parts (2) Parts

This is a binding-head screw used to fasten panels and components on compatible GE appliances. It provides secure, low-profile fastening where a binding head design is required for proper fit and alignment. What it does

• Secures panels, brackets, or small assemblies to prevent movement or rattling.
• Replaces a missing or stripped screw that causes loose parts or squeaks.
• Restores proper alignment for components that rely on the binding-head profile.
• Works where a shallow, rounded head and threaded shaft are specified.

• Use the correct driver size to avoid cam-out or head damage.
• Do not overtighten; snug until secure to avoid stripping threads or damaging parts.
• Disconnect power and follow all appliance-specific safety procedures before accessing panels.

This molded air tunnel directs heated air from the blower through the dryer drum for consistent airflow and efficient drying. Replaces a cracked or damaged duct to restore proper air circulation and help improve drying performance. What it does:

• Channels blower air into the drum and toward the lint screen and exhaust
• Prevents airflow loss from gaps or cracks that can reduce drying efficiency
• Helps maintain proper ventilation to reduce overheating and extended dry cycles
• Fits into the dryer's internal plenum to keep airflow focused and consistent

• One air tunnel/drying airflow duct

• Disconnect electrical power (and gas supply for gas dryers) before beginning service
• Access typically requires removing the dryer front panel or cabinet
• Align the tunnel with the blower housing and drum opening, then secure with the original fasteners or clips
• Check for a good seal around mating surfaces and reassemble panels before testing

This ventilation motor drives the vent fan to remove smoke, steam and cooking odors from the range hood assembly. It restores proper airflow so the ventilation system can clear air more effectively during use. What it does

• Replaces a worn or failed vent fan motor so the hood or microwave exhaust regains suction.
• Helps stop symptoms like no airflow, weak exhaust, or unusual motor noise during vent operation.
• Works with the fan/blower assembly to move air through the vent duct and filters.
• Matches OEM function and mounting so it integrates with the existing blower housing.

• One motor-ventilation (single motor unit)

• Install only with the appliance unplugged or power turned off at the breaker.
• Handle the motor and wiring harness carefully; reconnect all plugs and fasteners exactly as removed.
• Verify fan spins freely after installation before reassembling covers or panels.

The Fuse is an OEM part for GE microwaves. It serves as a safety device designed to protect the microwave from excessive current that can cause overheating and potential fire hazards. When the current flowing through the microwave circuit exceeds a certain level, the fuse blows or breaks, cutting off the power to prevent damage or fire.

Common causes for a fuse to blow include power surges, faulty wiring within the appliance, or the use of microwave inappropriate containers that cause sparks. It is essential to address these issues not only to replace the fuse but also to correct the underlying problems to prevent future failures.

Symptoms of a bad fuse include:

• The microwave suddenly stops working.
• No signs of power or response even when the microwave door is closed and the start button is pressed.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

A temperature sensor assembly that monitors internal temperatures and sends readings to the appliance control so the unit can maintain proper heating or cooling. Replacing a failed sensor restores accurate temperature regulation and consistent performance. What it does

• Detects and reports temperature to the electronic control or thermostat
• Helps the appliance maintain set temperatures for consistent operation
• A faulty sensor can cause inaccurate temperature readings or uneven heating/cooling
• May trigger temperature-related error codes or put the unit into a diagnostic/fail-safe mode

• Disconnect power to the appliance before attempting any repair
• Handle the sensor and its wiring gently; avoid bending or damaging the sensing tip or connectors
• Reconnect wiring securely and confirm correct routing to prevent interference with moving parts

A refrigerator temperature control thermostat that regulates internal cooling to keep food at the right temperature. Replaces a faulty control to restore proper cycling between compressor on/off and help maintain consistent fridge temperatures. What it does:

• Senses cabinet temperature and signals the compressor or control system to start or stop cooling
• Commonly used to correct a fridge that runs constantly or won't cool enough
• Helps restore regular on/off cycling and temperature stability when original thermostat fails
• Fits into the temperature control assembly and connects to the refrigerator's wiring harness

• Disconnect power to the appliance before installing to avoid shock or damage
• Basic hand tools are typically required; avoid forcing connectors or mounting clips

The Halogen Light Bulb is an OEM part for GE microwaves and ovens. It provides interior lighting, allowing you to clearly see the contents inside the appliance during operation. This illumination is essential for monitoring cooking progress and ensuring safety.

You should replace the halogen light bulb if it burns out or becomes damaged. Causes of a bad halogen light bulb can include regular use over time, electrical surges, or physical impact that can cause the bulb to break.

Symptoms of a bad halogen light bulb include:

• The light not turning on when the microwave or oven door is opened
• Flickering or dim lighting inside the appliance
• A burnt-out appearance or visible breakage in the bulb

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

A direct-replacement supporter housing that secures and aligns internal components for stable operation. Restores proper positioning inside the appliance so parts sit correctly and function as intended. What it does

• Provides a secure mounting point and structural support for internal components.
• Keeps parts properly aligned to prevent binding, rubbing, or premature wear.
• Helps reduce movement that can lead to rattling or vibration-related noise.
• Maintains correct clearances so associated parts operate smoothly.

• Disconnect power (and water if applicable) before starting any repair.
• Basic hand tools required; handle plastic housings gently to avoid cracking.
• Verify proper orientation and secure fasteners snugly—do not overtighten.