Kelvinator Freezer Parts

This cabinet breaker kit forms the insulating trim around the appliance opening. It provides a proper surface for the door or lid gasket to seal against and helps minimize condensation along the edge for clean, reliable performance.

• Creates the thermal break and finished edge around the cabinet opening
• Supports correct seating of the door/lid gasket for a consistent seal
• Helps reduce sweating or moisture at the perimeter
• Replaces cracked, warped, or missing breaker trim components

• Disconnect power before servicing; wear cut-resistant gloves
• Remove the door/lid if required for access and retain all fasteners
• Carefully remove old breaker components and clean the mounting surfaces
• Install the new breaker and corners, align evenly, avoid overtightening, and verify the gasket seals all around

This Temperature Controller regulates cooling by switching power to the compressor and related circuits to hold the set temperature. Replacing a failing controller restores accurate temperature control and reliable operation. What it does:

• Cycles cooling components to maintain the temperature you set
• Helps keep cabinet temperatures consistent for proper food storage
• Coordinates on/off operation to prevent overcooling or warm conditions
• Common failure symptoms: too warm or too cold, runs constantly or won't start, control/dial unresponsive

• 1 temperature controller

• Disconnect power before servicing—this is a line-voltage control
• Access the control area, label or photograph wire positions, and move wires one at a time to the new controller
• Reuse existing mounting hardware and any knob/overlay as applicable
• After install, set to mid setting and allow up to 24 hours for temperatures to stabilize

This bottom hinge replaces the lower door pivot on compatible Frigidaire refrigerators to restore proper door alignment and smooth opening. It provides a secure pivot point to help maintain an even close and consistent seal. What it does:

• Supports and pivots the lower edge of the refrigerator door for smooth opening and closing.
• Helps maintain correct door alignment so the gasket seals evenly.
• Common replacement for doors that sag, bind, or do not close evenly.
• Works with the factory mounting hardware and hinge locations on compatible models.

• Disconnect power and remove food and loose items from the door before starting.
• Always support the door while removing or installing the hinge to prevent injury or damage.
• Use appropriate hand tools and avoid overtightening fasteners; check door alignment after installation.
• Refer to your model's service manual or official parts diagram for model-specific steps and torque specs.

A small replacement mounting clip that secures interior trim or panels on select refrigerators, helping restore a snug fit and reduce loose, rattling parts. Fits where worn or broken clips allow trim to shift. What it does:

• Holds trim, panels or small components in place to prevent rattling and movement.
• Restores proper alignment of affected panels so edges sit flush and look finished.
• Simple mechanical fastening — replaces brittle or broken clips that no longer grip.
• Helps reduce noise caused by loose interior parts during normal operation.

• Always unplug the appliance or switch off power at the breaker before servicing.
• Remove the affected trim or panel per manufacturer instructions to access the clip location.
• Press the clip into the mating slot or post until it seats securely; use a small tool if needed to avoid fingernail or surface damage.
• Inspect surrounding mounting surfaces for cracks or wear; damaged supports may require additional replacement parts.

This inner door panel restores the interior surface and structural support for an oven door, helping maintain a proper seal and protecting internal components from heat and debris. It's a direct-replacement exterior/interior panel used during door repair. What it does:

• Replaces a cracked, dented, warped or otherwise damaged inner door panel to restore door rigidity and appearance.
• Protects insulation, wiring and other internal door components from direct contact with cookware, spills and heat.
• Helps maintain an even seal and reduce drafts or heat loss caused by a warped or loose inner panel.
• Stops rattling or vibration caused by loose or broken interior door pieces.

• Disconnect power to the appliance before starting any repair and allow the oven to cool completely.
• Handle panels and any glass carefully; wear cut-resistant gloves and eye protection.
• Installation typically requires removing the door and detaching interior trim and fasteners—keep hardware organized for reassembly.

This electronic control board is the refrigerator's main circuit board that manages temperature, defrost and user controls—restoring responsive control functions and resolving erratic or non-working control behavior. What it does:

• Controls compressor, fans and defrost cycles by sending signals based on sensor inputs
• Manages user interface commands and display response
• Can stop fridge cooling or cause incorrect temperatures when failing
• May cause intermittent operation, no display response, or failure to complete defrost cycles

• Disconnect power to the appliance before starting any work to avoid electrical shock
• Handle the board by its edges and avoid touching components or connector pins
• Verify connector orientation and seating; replace exactly like-for-like to ensure compatibility

This water inlet valve controls water flow to the refrigerator's dispenser and ice maker, restoring reliable water delivery and ice production when the valve is faulty or worn. What it does:

• Opens and shuts to allow water into the ice maker and dispenser when activated
• Common symptom: no water to dispenser or ice maker
• Common symptom: reduced or intermittent water flow from dispenser
• Common symptom: ice maker not filling or producing smaller/soft ice
• Can cause visible leaks at the valve or connections when failing

• One water inlet valve assembly

• Turn off water supply and unplug appliance before beginning work
• Relieve any pressure in the water line and have towels handy for minor spills
• Verify inlet/outlet hose orientation and tighten all fittings to OEM torque; use replacement gaskets if supplied

This corner cabinet trim replaces a damaged or missing corner finish piece on the appliance cabinet, restoring a clean edge and helping the door and adjacent panels fit correctly. It provides a cosmetically complete appearance. What it does:

• Covers and protects the cabinet corner for a finished look
• Helps maintain proper alignment and spacing at the cabinet corner
• Commonly replaced when cracked, chipped, broken, or missing
• Restores cosmetic appearance and helps prevent exposed sharp edges

• One corner cabinet trim piece

• Turn off and unplug the appliance before accessing trim or removing panels
• Trim may secure with clips, screws, or snap-fit tabs—inspect fasteners and retainers before removal
• Handle edges carefully; use appropriate tools to avoid scratching adjacent surfaces

A small metal clamp that secures the refrigerator's capillary (temperature sensing) tube to the cold control so the thermostat reads temperatures accurately. Replaces worn or missing clamps to keep the sensing tube stable and prevent movement-related issues. What it does:

• Holds the capillary/sensing tube firmly against the cold control or cabinet
• Helps maintain accurate thermostat sensing by preventing tube movement
• Reduces vibration or rattling from a loose sensing tube
• Stops intermittent temperature swings caused by a displaced capillary tube

• Disconnect power before servicing the appliance.
• Handle the capillary tube gently; avoid kinks or sharp bends.
• Install clamp over the tube and secure to the control or bracket using the factory hole or fastener; do not overtighten.

This left-side tiltout end cap replaces the damaged or worn plastic end piece that secures and guides a fridge/freezer tilt-out or dairy bin. Restores a secure fit and smooth opening for the tilt-out assembly. What it does:

• Replaces the left end cap on a tilt-out/dairy bin assembly
• Helps keep the drawer aligned and held in place during use
• Reduces rattling or catching when opening and closing the tilt-out
• Matches OEM fit and mounting points for direct replacement

• One left tiltout end cap

• Remove contents and the tilt-out bin before attempting replacement
• Installation typically requires basic hand tools and gentle prying to disengage clips
• Inspect mating clips and housing; replace or repair any broken tabs before reinstalling

This is a replacement retainer clip used to secure interior trim and small components on compatible refrigerators. It restores proper fit and prevents loose panels, rattles, or improperly seated trim. What it does:

• Secures trim, panels or small components in place to maintain proper alignment
• Prevents rattling, gaps, and shifting caused by broken or missing clips
• Replaces brittle or cracked clips that no longer hold parts securely
• Helps restore a clean, finished fit where the original clip has failed

• Disconnect power to the appliance before beginning any service
• Remove surrounding trim or panels carefully to access clip location; small fasteners may be present
• Press replacement clip into position until it snaps in; do not force or bend brittle plastic
• If other clips or fasteners are damaged, replace them to ensure a secure fit

A replacement temperature control (thermostat) that regulates the refrigerator/freezer cooling cycle so food stays at the set temperature. Restores reliable on/off cycling when the original control fails. What it does

• Sends the signal to the compressor and fans to maintain the selected interior temperature.
• Replaces a faulty control when the appliance is too warm or too cold, or when temperatures fluctuate.
• Can stop short-cycling or continuous-run issues caused by a defective control.
• Works with the fridge's user temperature selector to restore normal cooling responses.

• Disconnect power to the appliance before starting any repair to avoid shock or injury.
• Handle control and wiring harness carefully; note or label wire locations before removal.
• Mount the control in the original position and reconnect wires to the matching terminals.

This hinge-side door stop helps limit door travel and protect the hinge assembly from over-rotation for a secure, consistent door movement. Replaces a worn or broken hinge-side stopper to restore proper door alignment and operation. What it does:

• Acts as the stop/breaker on the hinge side to prevent the door from swinging past its intended range
• Helps reduce stress and wear on the hinge and door seal caused by over-rotation
• Commonly replaced when the door catches, over-rotates, or the hinge feels loose
• Works with the hinge assembly to keep door movement smooth and predictable

• Disconnect power to the appliance before starting any repair
• Remove the door or access hinge per your model's service instructions to reach the stopper
• Inspect adjacent hinge hardware and fasteners; replace any stripped or damaged parts
• Use proper hand tools and follow manufacturer torque and alignment guidance