Kitchenaid Cooktop Parts

Rubber grommet that cushions and protects wiring, hoses or components where they pass through metal openings. Helps reduce chafing, vibration and noise while restoring a secure, flush fit when a worn grommet is replaced. What it does

• Protects wires, cables or hoses from rubbing against sharp metal edges.
• Cushions and isolates components to reduce rattles and vibration noise.
• Helps keep openings sealed from debris and limits movement of the routed part.
• Common symptoms that indicate replacement: torn, cracked or missing grommet; visible chafing on wiring; rubbing or new rattling sounds.

• Disconnect power (and water, if applicable) before accessing the repair area.
• Remove any panels or retainers that block the grommet location; note fastener placement.
• Press the grommet into the opening until seated flush; a small amount of soapy water can ease installation—avoid sharp tools that can tear the part.
• Inspect surrounding wiring/hoses for damage and replace or repair as needed.

This genuine-style replacement power cord restores electrical connection to compatible appliances, letting the unit receive mains power safely. Use it to replace frayed, damaged, or missing cords and stop intermittent or no-power issues. What it does:

• Carries mains power from the wall outlet to the appliance
• Replaces damaged or worn cord that causes intermittent power or no power
• Eliminates exposed wires, melting, or visible cord damage that can be a safety hazard
• Restores secure strain relief and connector fit when original cord is failing

• Disconnect the appliance from power before starting any work
• Follow the appliance service manual for access and wiring; correct terminal connections
• Tighten strain relief and secure wiring to prevent pinching or chafing

This chrome handle medallion restores the finished look of a damaged or worn appliance handle by replacing the decorative cover. It improves appearance and helps protect the underlying handle hardware from wear. What it does:

• Replaces a scratched, dented, or faded handle trim piece to renew the appliance's appearance
• Covers and protects the handle mounting area from everyday wear
• Matches chrome finishes for a consistent, factory look
• Helps eliminate cosmetic blemishes that make the appliance look older

• Basic hand tools are typically required; follow the appliance's user manual or parts diagram for correct removal/replacement of the handle
• Remove the handle or access panel carefully to avoid scratching adjacent finishes
• Keep hardware and fasteners organized during disassembly so original parts can be reused

This replacement door handle restores a secure grip and smooth operation to your appliance door. It provides a direct-fit swap for worn, cracked, or broken handles so the door opens and closes reliably. What it does:

• Replaces the damaged or broken door handle so the door can be opened and closed safely
• Provides a comfortable grip and restores original door appearance
• Reduces the risk of further damage from using a compromised handle
• Helps prevent door misalignment caused by loose or missing hardware

• Verify power is off or appliance is in a safe state before starting any work
• Installation requires removing the old handle hardware and securing this handle with the original fasteners
• Keep small screws and retainers in a safe place during installation to avoid loss

Color: Black

NAT to LP gas conversion kit

This flush-style control knob fits onto the appliance's control shaft to select settings with a smooth, secure turn. Replace worn or missing knobs to restore reliable adjustment and a clean, factory look. What it does:

• Attaches to the control shaft to operate the underlying switch or valve
• Provides a secure grip for selecting and adjusting settings
• Restores control when the original knob is cracked, stripped, or missing
• Typical symptoms include a knob that spins freely, falls off, won't turn the control, or is visibly damaged

• 1 control knob

• Disconnect power (and shut off gas supply if applicable) before servicing
• Pull the old knob straight off the shaft—do not pry from the sides
• Align the new knob's opening with the control shaft and press straight on until fully seated
• Restore power and test for smooth, proper operation

The Clip is an OEM component specifically designed for Whirlpool free-standing electric ranges, securely fastening rack guides, and wire assemblies. This versatile clip features corrosion-resistant anchors and firm spring coils.

Causes of failure involve metal fatigue weakening the spring over years of expansion and contraction during heating, worn surfaces losing grip, or damaged barbs failing to anchor the racks correctly.

Symptoms of a bad cooking rack clip include:

• Loosened racks skewing pans off-center  
• Detached wires posing burn and electrical hazards
• Rattling components exacerbating noises  
• Difficulty transferring baking sheets without obstruction

Replace yours today with this genuine OEM Whirlpool clip. Compatible with KitchenAid, Maytag, and Jenn-Air appliances as well, its reinforced coils maintain constant tension for organized baking.

This switch seal is a replacement gasket that helps keep moisture and debris away from the appliance's door/control switch, protecting the switch assembly and helping restore reliable door detection and operation. What it does:

• Seals the area around the door/control switch to block water, lint, and grime.
• Helps prevent intermittent trips or failures caused by moisture or foreign material contacting the switch.
• Promotes consistent switch actuation and can extend the service life of the switch assembly.
• Useful when the existing seal is cracked, torn, flattened, or missing.

• Disconnect power before servicing to avoid electrical shock.
• Access typically requires removing the door trim or control panel—follow your model's service instructions.
• Inspect the switch and surrounding area for damage or corrosion and clean before installing the new seal.

This small mounting clip secures small panels and components on compatible Whirlpool appliances, restoring proper fit and preventing parts from coming loose. It's a simple replacement that helps stop rattles and misaligned panels. What it does:

• Secures trim, panels or small components to the appliance frame to maintain proper alignment
• Prevents parts from shifting or vibrating during operation, reducing rattling noises
• Restores fit where a broken or missing clip allowed gaps or loose pieces
• Designed to snap into place for a secure hold without added hardware

• One clip

• Disconnect power to the appliance before attempting any repair
• Remove any trim or panels carefully to access the clip location; note original orientation
• Press or snap the clip into the mounting slot until it seats; some locations may require a flat tool or light force
• Replace or repair the adjacent parts for a secure fit

This switch seal is a small rubber gasket that protects a control or door switch from moisture and debris, helping maintain reliable operation and prevent damage to the switch assembly. What it does:

• Creates a moisture- and dust-resistant barrier around a switch to reduce shorting and corrosion
• Helps keep switches operating smoothly by blocking contaminants that cause sticking or intermittent contacts
• Supports safe electrical performance by keeping water away from switch terminals and housings
• Common symptom linkage: switch malfunction, intermittent control, or moisture-related failures near switch area

• Disconnect power to the appliance before inspecting or replacing the seal
• Remove surrounding trim or components carefully to avoid damaging the switch or housing
• Confirm correct orientation and full seating of the seal during reassembly for an effective barrier
• If the switch shows damage or corrosion, replace the switch assembly as well

The Burner Cap is an OEM component specifically designed for Whirlpool gas ranges. Located atop each surface burner element, it creates an ideal heating footprint optimized for common cookware.

Symptoms of a faulty burner cap often include misshapen or distorted areas from prolonged exposure to high temperatures. Discoloration or scaling along outer rims occurs as well from mineral accumulation over many years.

Symptoms of a bad burner cap include:

• Caps appear badly twisted or misshaped
• Grime builds up in hard-to-clean sections
• Flame patterns become irregular or unstable
• They show signs of cracking

This OEM Whirlpool replacement burner cap restores safe, uniform heating. Installed promptly to remedy burners scorched underneath, it averts continued performance compromises from further damage or debris traps. 

Compatible also with some GE and Frigidaire range models, this part maintains efficient energy use for cooking convenience. 

This genuine replacement wire harness connects and routes power and signal lines between appliance components, restoring reliable electrical communication for normal operation and control response. What it does:

• Replaces damaged or frayed wiring that can interrupt power or signals
• Restores reliable connections between controls, motors, and sensors
• Helps resolve intermittent operation, loss of certain functions, or failure to start when caused by wiring faults
• Provides factory-style connectors and routing for secure, vibration-resistant connections

• Disconnect power to the appliance before starting any repairs
• Handle connectors carefully; match connector shapes and colors to the original
• Route the harness as the OEM diagram specifies and secure with clips or ties to prevent chafing

Color: Biscuit. Other colors: For black use WP9750372FF, for white use WP9750372FW.

This switch bracket mounting seal replaces a worn or damaged seal that cushions and protects the door or control switch mounting area. It helps keep the switch assembly seated and reduces debris and moisture intrusion for reliable operation. What it does:

• Seals the switch bracket mounting area to protect the switch from lint, dust and moisture
• Helps keep the switch properly positioned for accurate door or control sensing
• Can prevent intermittent or failed switch contacts caused by contamination or misalignment
• Useful when replacing a brittle, torn or missing mounting seal during switch or door repairs

• Disconnect power to the appliance before starting any repair
• Remove the door or panel per service instructions to access the switch bracket area
• Fit the seal into the bracket groove or around the switch housing, ensuring full seating without stretching
• Inspect adjacent clips or screws and reuse or replace as needed; test the switch function after reassembly

This ground wire provides a safe chassis connection to restore proper grounding and reduce shock and electrical-fault risk. It replaces a frayed, corroded or missing ground lead to help keep the appliance electrically safe. What it does

• Connects the appliance chassis to the grounding system to prevent stray voltage on metal surfaces
• Restores a secure ground path if the original wire is broken, loose, or corroded
• Helps stop intermittent power faults or nuisance tripping caused by a compromised ground
• Addresses symptoms like visible wire damage, loose ground connection points, or grounding-related electrical issues

• One ground wire

• Always disconnect power (unplug or shut off the circuit breaker) before starting work
• Attach the ring/terminal ends to the designated chassis ground screw and the equipment ground point
• Route the wire away from moving parts, heating elements, and sharp edges; secure with existing clips or fasteners
• If terminal hardware is missing or damaged, replace with equivalent OEM-style fasteners and torque to specification