Parts for Ge ZGP486LDR5SS: Large Door Assembly Parts

This mounting screw secures appliance components to the chassis for a tight, rattle-free fit. Replacing a missing, stripped, or corroded fastener helps keep panels, brackets, or burner assemblies properly aligned and secure.

• Fastens designated parts to the appliance frame or mounting points
• Helps maintain proper alignment of panels, trim, brackets, or burner assemblies
• Restores hold when the original screw is worn, rusted, or lost
• Symptoms include loose or wobbly components, rattling/vibration, or visible gaps

• Disconnect power; allow all surfaces to cool. For gas units, also shut off the gas supply.
• Use the correct driver/bit; avoid cross-threading.
• If mating threads or clip/nut are damaged, repair or replace them before installing.
• Tighten until secure; do not overtighten to prevent stripping.

This small end cap fits the end of an extension piece to act as a stop and finish. It restores a secure, finished edge so the sliding component or trim stays aligned and doesn't over-travel during use.

• Caps the end of an extension rail or trim to prevent over-travel and pullout
• Keeps the assembly aligned to reduce wobble
• Replaces cracked, missing, or worn caps
• Helps eliminate rattling and exposed edges

• Disconnect power and allow all hot surfaces to cool before servicing
• Access the end of the extension/rail; release any locking tab and remove the old cap
• Align and snap or press the new cap into place
• Verify smooth travel and a secure stop after installation

This 27" oven door gasket seals the gap between the door and oven body to help maintain proper cavity temperature and reduce heat loss during cooking. It restores a tighter door seal for more consistent baking and roasting. What it does:

• Replaces worn or torn door seal that lets oven heat escape
• Helps the oven reach and maintain set temperatures more reliably
• Reduces hot spots and uneven cooking caused by a failing seal
• Minimizes heat transfer to surrounding cabinetry and reduces energy loss

• One door gasket (27")

• Disconnect power and allow the appliance to cool completely before starting
• Remove the old gasket and any adhesive or fasteners before installing the new gasket
• Press the new gasket into the door channel evenly, ensuring proper orientation and a continuous seal

This 27" glass oven door provides the visible, heat-resistant window for an oven cavity so you can monitor cooking while keeping heat contained. Durable replacement glass restores a secure, clean-looking door surface. What it does:

• Replaces damaged, cracked, or chipped oven door glass to restore safe viewing
• Helps maintain oven temperature by sealing the door opening
• Prevents food splatter from contacting internal components
• Restores proper visibility for checking progress without opening the door

• One 27" oven glass door

• Disconnect power to the appliance and allow the oven to fully cool before starting
• Handle the glass with gloves and place on a protected, padded surface to avoid damage
• Some door removal or hinge access is typically required; keep track of fasteners and brackets

This inner oven door glass replaces a cracked or cloudy panel to restore a clear view into the oven cavity and help the door seal properly. It fits into the oven door assembly and restores safe, functional operation. What it does:

• Replaces damaged, cracked, or discolored inner oven door glass
• Restores visibility so you can monitor cooking without opening the door
• Helps maintain the oven door seal and proper heat containment
• Prevents loose glass fragments that could fall into the oven cavity

• High-level replacement: typically accessed by removing the outer door panel; follow the oven model's service manual
• Handle glass carefully; wear cut-resistant gloves and eye protection
• Disconnect power and allow the oven to cool fully before starting work
• If clips, brackets, or adhesive are required, obtain the specific hardware for your door variant

This replacement screw secures appliance components so panels, brackets, and trim stay tight and aligned. Use it to replace a missing, stripped, or rusted fastener and restore a solid, rattle-free fit in the affected assembly.

• Fastens parts to the chassis/frame or mounting brackets
• Replaces lost, damaged, or corroded hardware
• Can help address loose or vibrating panels and minor misalignment
• Maintains a secure attachment during normal operation

• Disconnect power before servicing; for gas appliances, also shut off the gas supply
• Match the screw to the original location and reuse any clips or washers if present
• Start threading by hand to avoid cross-threading; tighten snugly without overtightening
• Repair/replace damaged receiving threads or clip for proper hold