Lawn Hawk Lawn Mower Parts

This replacement part is a hex bolt. It is a genuine replacement part made by MTD. Hex bolts are named because they are shaped like a hexagon and are different from the regular circle-shaped bolts. These parts are able to hold other parts secure and in place so that everything can operate as needed. A new hex bolt might be needed if the current ones are damaged in any way. It is possible that these bolts become stripped or lodged in place over time due to normal wear and tear and should be replaced. The repair should be fairly easy, only requiring a screwdriver or pliers if the previous part is stuck. Be sure the engine is completely powered down before beginning this repair. This bolt is sold individually. Be sure to purchase the correct amount as many appliances require more than one. This is a genuine OEM replacement part sourced directly from the manufacturer.

This carriage screw is a replacement part for Craftsman, Yard-Man, MTD, and Yard Machines lawnmowers and snowblowers. Carriage screws are made from durable metal and have a flat tip with a round head and threading on a portion of the shank. These screws may also be called coach screws or plow screws and are corrosion resistant, strong, and resistant to scratches. If a carriage screw breaks or beings to become weak, replacement may be required. In many cases, it’s possible to inspect the screw to determine whether it is still doing its job. The screw might be rusted or appear beaten up, which means it should be replaced. In most cases, it can be removed using a wrench unless the rusting is extreme. The new screw can be placed into the original hole and tightened to keep your snowblower running correctly. This is a genuine OEM replacement component for use with lawn tractors and snowblowers. It’s made of metal and can be found in various locations depending on the tool model. The screw comes as an individual item and will require the use of a wrench to install.

This OEM replacement push cap can be used in a variety of lawn and garden equipment. The push cap is secured to the end of a shaft, providing protection to the user from the sharp metal edge of the shaft. The push caps that are included with the machines may wear out over time or fall off in some cases, creating an injury risk involving sharp metal edges. These push caps are high-quality and made from durable plastic. They are easy to install. The OEM push cap is a genuine part made by the original manufacturer, to ensure quality and s proper fit. The push caps can be used on lawn tractors, chippers, shredders, log splitters, and other equipment. Some of the brands that this push cap is compatible with include MTD, Husky, Yard-Man, Bolens, Troy-Bilt, Ryobi, Yard Machines, and cub Cadet.

This authentic OEM replacement part is a steering shaft intended to be used on lawn tractors. A steering shaft connects the steering wheel to the rest of the steering mechanism. As a user rotates the steering wheel, the steering shaft also rotates to move the pinion along the steering rack. The more the steering shaft rotates, the more the pinion travels along the rack, and the more the wheels turn in the direction of the steering wheel. Steering shafts most commonly have to be replaced if the steering mechanism becomes worn out or stripped. When this happens, steering will be more difficult and cause strange clunking sounds. The steering wheel may also feel looser than normal and may not recenter after being turned. Leaving a faulty steering shaft unrepaired can lead to accidents. Replacing the steering shaft means detaching the lower deck of the lawn tractor from the upper frame, then removing the steering wheel, adapter, fuel tank, and old steering shaft. This requires a socket wrench set and can is an intermediate-level repair. This part is compatible with MTD, Yard Machines, Troy-Bilt, Yardman, Husky, and Bolens lawn tractors. It ships individually and is sourced from the original manufacturer.

Carriage bolts are flat-tipped with round heads, and their function in small engine appliances is to fasten together components and to secure that connection with a nut. There are various reasons that a carriage bolt might have to be removed and replaced, among them misplacement of the small, easily lost part. Other reasons to replace a carriage bolt could include damage or erosion that prevents the bolt from attaching the materials to one another effectively. If a carriage bolt is subject to this kind of damage, it should be replaced before using the small engine appliance. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This genuine MTD carriage bolt can be used as a replacement part for several different kinds of appliances that require small engines, including lawnmowers, snowblowers, wood-chippers, tillers, string trimmers, leaf blowers, and edgers. The OEM carriage bolt is compatible with the following brands: Craftsman, Toro, Cub Cadet, Ryobi, Troy-Bilt, Murray, Yard Machines, MTD, Huskee, Montgomery Wards, Bolens, Yard-Man, Turf King, and MasterCut. This part is sold individually.

This authentic OEM replacement ball joint assembly is a part of the front suspension of a lawn tractor or riding mower. Suspensions are complex systems that include joints, bushings, and bearings that must all work together to turn and maintain contact with the ground. This ball joint assembly helps to connect all of these components. It works similarly to a human hip in that it has a joint and a ball that allows for pivot motions. The most common reason for a ball joint assembly to go bad is if it loses lubrication or becomes gritty. In order to work smoothly, these joints must stay well oiled or else they will grind and break. If the ball assembly breaks, use a wrench to disengage the wheel and change out the part. This is a fairly straightforward repair and should not take more than a few minutes. This replacement assembly is a high-quality part for Cub Cadet, Huskee, MTD, Yard Machines, Murray, Troy-Bilt, Bolens, Ryobi, and Yard Man machines. This part is sourced from the original parts manufacturer and ships individually.

The choke cable opens and closes the valve that controls the choke, or throttle, on the lawn mower. When the choke handle is depressed or pulled out, it will open or close the butterfly valve, controlling fuel flow to increase or decrease the speed and performance of the mower. Based on the type of tension cable that is used, this part can wear out or even snap from regular use and need to be replaced. The durable choke cable will be easy to install, but always disconnect the spark plug and wear gloves. This genuine OEM choke cable can be used with mowers from RYOBI, MTD, Husky, Yard Machines, Yard-Man, Troy-Bilt, Cub Cadet, and Bolens. It is made of metal and plastic and comes directly from the manufacturer to ensure quality. Sold individually.

The hex head self-tapping screws are designed for a number of applications in lawn and garden equipment, primarily holding machinery and engine parts together. Over time, screws can become stripped, fall out, or otherwise get damaged, resulting in a need for replacement. When replacing screws and other hardware, always be sure to disengage or disable any power supply to reduce the risk of shock or other injuries. The self-tapping screw makes it easy to replace, and the fact that they are manufacturer-guaranteed ensures a perfect fit for compatible machines. This OEM self-tapping screw is compatible with several machines from RYOBI, MTD, Husky, Cub Cadet, Yard-Man, Troy-Bilt, Bolens, and Yard Machines. It can be found in lawnmowers and tractors and can be in multiple locations, depending on the exact model. This screw is sold as a single piece; order multiple quantities if needed.

This is a self-tapping screw that can be used on a wide variety of lawn and garden equipment in many applications. A self-tapping screw is used to secure metal, wood, plastic, and brick together. When using a self-tapping screw, there's no need to drill a pilot hole since the screw makes its own hole. The only exception is with metal, which will still need a drilled hole before installation. There are many situations when a screw may need to be replaced. Some screws are damaged or broken, while others can become loose and no longer hold materials together. Screw heads can become stripped, which will also mean they need to be replaced. A visual inspection can often give an indication of whether you should replace a self-tapping screw. This is a genuine OEM hex head screw that can be used on various lawn and garden equipment, including wood chippers, lawn mowers, snowblowers, log splitters, tillers, edgers, and leaf blowers. It's compatible with products by MasterCut, Craftsman, Turf King, Cub Cadet, Yard-Man, Ryobi, Bolens, Troy-Bilt, Montgomery Wards, Murray, Huskee, Yard Machines, MTD, and more. This screw is sold individually.

This is a fully-threaded hex tap screw that can be used in a wide range of machines from many of the top brands making lawn and garden equipment. The screw is used to help fasten pieces of the machine together and to provide a tight connection. If the screw is damaged in some way or is missing, it can cause a range of problems in the machine. Problems with the screw might cause the machine to not hold together properly. It could cause added vibration in the machine.The hex tap screw is made from metal and it should last for a long time without needing to be replaced. However, problems can happen. The head could become damaged and difficult to turn, which will require a replacement before the problem worsens. The threads could be stripped, or the screw could have become corroded. It might also be lost and will need to be replaced.The hex tap screw can work with machines from Craftsman, Ryobi, Bolens, Troy-Bilt, MTD, Husky, Yard Machines, and Yard-Man. It is sold individually and is a genuine OEM replacement part.

This lock washer is used frequently for a number of applications on power yard equipment. The size, 5/16, is the default for many small engine housing and manifold applications. Lock washers are used with machined bolts to fasten engine blocks to the housing of the equipment being used. The compressed washer is able to handle the constant vibration of the small gasoline engine without losing the seal between the screw or bolt and the housing. Typically these lock washers only need to be replaced when they are misplaced during repairs or when the screws that attach them have to be chiseled or cut away, meaning the washers are destroyed as well. These OEM certified replacement washers have been manufactured to the same specifications as the originals they are replacing. In addition to lawn mowers, lock washers of this type and size are frequently used on blowers, lawn tractors, cultivators, snowblowers, and trimmers. Brands compatible with this type of washer are Murray, Husky, Poulan, Bolens, Yard-Man, Cub Cadet, Troy-Bilt, Yard Machines, MTD, and Ryobi.