Parts for Mtd 26M: Lawn Mower Parts

This control handle is designed specifically as a replacement for use on select walk-behind lawn mowers. The control handle is the safety that is engaged to allow the engine to run. When holding the control handle in, the pull start can be activated and the engine will run. Once the control handle is released, the engine will stop. In the event that the control handle becomes damaged or fails, it will need to be replaced so that the mower can continue to be used. This handle can provide a genuine replacement for compatible models. This control handle is manufactured to exact standards by MTD and provides an exact fit. It is compatible with hundreds of models, including select models from RYOBI, Yard Machines, Troy-Bilt, Yard-Man, Husky, Bolens, and Cub Cadet. This part is also known as the control bar, control handle, engine stop handle, bail control, or mower bail. It is made of durable metal and sold individually. No tools are required for the installation of this part. To replace the handle, simply squeeze the existing control handle to remove it from the outer handle, and then align the new handle and slide it into place. When properly installed, the pressure will hold it in place and allow for proper operation.

This replacement part is a cable control drive. This is a genuine replacement part made by MTD. This part is typically found in lawn mowers and allows the user to control different settings during use.A new cable control drive might be needed if the current one is missing or damaged in any way. The wires in this part can easily become worn down over time and might cause the mower to not work effectively. If the wires are visibly stripped, it is recommended that the user replace this part as soon as possible. Work gloves are recommended while completing this job to ensure safety.This is a genuine OEM replacement part. This part is sold individually and is sourced directly from the manufacturer.

This upper handle can be used as a replacement part for a lawnmower or snowblower. The upper handle allows the user to control the movement of the equipment while it is in operation.If the part suffers damage from direct impact or wears down from use over time, it may need to be replaced. An upper handle can suffer damage in the form of piercing, cracks, scrapes, punctures, and corrosion of the metal material. If this damage makes steering the lawnmower or snowblower difficult, the handle should be removed and replaced with this genuine OEM replacement part before using the appliance again. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This upper handle is a genuine MTD part, sold individually. It is compatible with the following outdoor appliance brands: MTD, Troy-Bilt, Yard Machines, Huskee, Craftsman, Yard-Man, and Bolens.

A rope guide eyebolt is an important piece of hardware designed for use with pieces of outdoor lawn and garden power equipment that have small engines, such as lawn mowers. It is compatible with products by brands such as Craftsman, Bolens, Husky, Yard Machines, Yard Man, MTD, and Troy-Bilt.The rope guide eyebolt part plays a valuable role in making the lawn mower easier to operate. The metal rope guide eyebolt is to be mounted to the side rail of the handle, which then keeps it secured with a handle knob. The rope guide eyebolt keeps the starter rope on the upper handle for ease of access. The purpose of all of this is simply to keep the rope out of the way while operating. The replacement or repair process of the rope guide eyebolt should be straightforward, but the user replacing the part should always be sure to wear gloves during any assembly, replacement, or installation processes.The user should also refer to the owner's manual of their equipment and any guiding diagrams that clarify the placement location. This part is made out of metal. This rope guide eyebolt is an original OEM part sourced directly from the manufacturer, MTD. It is sold individually.

This is a knob handle that is used on various types of lawn and garden equipment. It is responsible for helping to make adjustments to the upper handle of the lawnmower or other machine. If the knob handle no longer works, is broken, or falls off, adjustments can no longer be made to the equipment. If this situation occurs, the knob handle will need to be replaced.Take a look at the knob handle and determine if it has been damaged. It could have cracks, broken areas, or excessive scratches that make it hard or impossible to use. If the knob handle is not present, this also necessitates a replacement. The part is easy to replace and requires no tools to install. Simply remove the old handle and place the new one in the same location.This is an authentic OEM replacement knob handle that is directly sourced from the manufacturer. It is sold as an individual component. The knob handle is used on lawnmowers, snowblowers, string trimmers, leaf blowers, wood chippers, and edgers. It fits various models offered by MasterCut, Yard-Man, Bolens, Montgomery Wards, Huskee, MTD, Yard Machines, Murray, Troy-Bilt, Ryobi, Cub Cadet, and Craftsman.

This replacement curved hd. screw is also known as a carriage bolt. The screw can be used on many types of lawn and garden equipment. The purpose of the screw is to hold and support the upper and lower handles of the machine. It works along with the hand knob to help secure the handles, but buyers should know that the knob is sold separately. Owners might need to replace the carriage bolt if it has become corroded or no longer properly secures the handles. If the owner has lost the bolt, they will need to buy a new one before they can use their machine. The replacement for this part is fast and simple. This is an authentic OEM replacement curved hd. screw that is sold individually. It is for use with lawn mowers, tillers, snowblowers, wood chippers, edgers, and leaf blowers. It is compatible with certain models from Craftsman, Cub Cadet, Ryobi, Troy-Bilt, Husky, Yard Machines, MTD, Huskee, Montgomery Wards, Bolens, Yard-Man, and MasterCut.

A flange lock nut, also known as a flange lock or a lock nut, is created to be used in various types of lawn and garden equipment. This flange lock nut holds other parts in place and, when properly threaded, will resist loosening. Over time, a flange lock nut may begin to weaken and may become loose or break. If it appears to be broken or weak, a replacement is required. Flange locks can be adjusted and uninstalled after use. When replacement is required, you may need a socket set, screwdriver, hacksaw, and butane torch. The socket wrench will loosen the bolt it is connected to, while the torch is used to heat the lock nut. A socket wrench may remove the nut, but sometimes cutting it with a hacksaw is required. This flange lock nut is a genuine OEM component directly from the manufacturer and comes in an individual unit. It is made of metal, a gold color, and can be found in various areas of lawn equipment. It works with lawnmowers, trimmers, snowblowers, cultivators, tillers, and leaf blowers by Poulan, MTD, Toro, Cub Cadet, Murray, Troy-Bilt, Bolens, Yard Machines, Craftsman, and Yard-Man.

A star knob connects the upper and lower handles on an outdoor appliance, and if removed, the upper and lower handles are quick-released. This part is made of black heavy-duty black plastic, and the threads are made of steel. Over time, the threading can become worn out, making the connection loose, and causing the two handles to no longer stay in place. Star knobs are a straightforward repair that can be done in a matter of minutes. Just unscrew the original, damaged knob and screw in the new knob. The knob is designed to be unscrewed by hand, so there is no need for additional tools to make this repair. This genuine OEM replacement part is designed for a variety of outdoor appliances, including lawnmowers, edgers, chippers, tractors, trimmers, and cultivators. This star knob is compatible with Yard Machines, Yard-Man, Cub Cadet, Bolens, Craftsmen, and Ryobi products. This part ships individually.

This is a seven-inch cable tie that is used with different types of lawn and garden equipment. It is most commonly used to secure the cable onto the handle of the lawnmower or tiller so it is secure. The cable tie is made of durable plastic but can be damaged or break. When this happens, the tie will need to be replaced to ensure the cable stays on the handle.If the cable tie needs to be replaced, no tools are needed. In the situation where other parts need to be replaced at the same time, a basic set of tools and a pair of work gloves may be required. Turn off the yard equipment and place it on a stable surface before replacing the broken cable tie. The old tie can be removed so the new one can be installed before further use.This cable tie is an authentic OEM replacement part that is directly sourced from the manufacturer. This product is sold individually. The component is designed to be compatible with lawnmowers, lawn tractors, tillers, and snowblowers manufactured by MTD, Troy-Bilt, Yard-Man, and Yard Machines.

A hex screw fastens and holds two components together. It has a hexagonal head and features threading starting underneath the shoulder down to the tip. Its all-metal construction offers rigidity and longer lifespan. It is also threaded, so you can conveniently loosen or tighten in position. It measures 1/4-20 x 0.5 inch and comes in brass or gold color. Take note that this replacement hex screw may beused in different locations of a machine. Double check the device’s model number for compatibility. To install this hex screw, you will need a hex wrench or a hex socket. This hex screw is a replacement made by MTD. This screw/bolt may be used on lawn mowers, snowblowers, tillers, string trimmers, leaf blowers, edgers, chainsaws, pole pruners, log splitters, or wood chippers made by Craftsman, Toro, Cub Cadet, Ryobi, Troy-Bilt, Husky, Murray, Yard Machines, MTD, Huskee, Montgomery Wards, Bolens, Yard-Man, Turf King, or MasterCut. This OEM hex screw is sold individually.

This is a flanged lock nut. It’s designed to apply tension, typically on a joint that needs to have a certain amount of flex. As such, it’s mostly used on snowblower chutes and lawnmower handles. They can remain in place, but with a forgiving connection that can take a beating. The nut size is 3/8, with a thread size of 16. A lock nut will generally last for many years. However, the silicone ring inside will wear down if it’s frequently tightened and loosened. It needs to be replaced when it will no longer reliably remain in place. Generally, this begins as a symptom of slight slippage and worsens as time goes on. Thankfully, whether it’s being used on a snowblower or a lawnmower, this nut is generally straightforward to access. Simply unscrew the old nut, then screw the new nut on until it’s nice and tight. Our flanged lock nuts are genuine OEM MTD nuts, and they are sold individually.

This hex screw and lock washer are commonly used with lawn mowers and other small engines to secure a motor to the housing of the equipment. It is machined in such a way that it binds the manifold and frame permanently. There are occasions when these bolts have to be removed, typically when major repairs are performed on the engine. In those cases, users often find it advisable to replace the hex bolts and washers with new ones. It happens as well that these screws are so tightly fastened that they cannot be unscrewed and must be cut off. In those cases, it is necessary to replace the original screws. These replacement screws and lock washers are genuine OEM certified replacements that are manufactured to be identical to the hardware they are replacing. In addition to mowers, these hex screws are used to secure engines to devices such as log splitters, edgers, shredders, trimmers, and snowblowers. This screw is compatible with devices made by Husky, Yard-Man, Cub Cadet, Troy-Bilt, Ryobi, Bolens, and Yard Machines.

This v-belt is a genuine MTD part, sold individually. This v-belt can be used as a replacement part in a lawn mower. The purpose of a v-belt in a lawn mower is to manage the equipment's speed.The v-belt in a lawn mower might need to be replaced if the component is damaged sufficiently to render it beyond functionality or severely reduced in functionality. This could occur if the v-belt is torn, ripped, scraped, dented, cracked, eroded, punctured, or otherwise damaged; if this damage renders the component beyond repair, it should be removed and replaced by this genuine OEM replacement part before using the lawn mower again, as safe use of the lawn mower cannot be guaranteed without a v-belt in place. Remember to always wear gloves when handling, repairing, and operating outdoor equipment.This OEM part is a genuine replacement that is sold individually and sourced directly from the manufacturer. This v-belt is compatible with the following outdoor appliance brands: MTD, Yard Man, and Yard Machines.

A C-clip is a retaining ring with open ends that snap into place. It is commonly fitted onto a pin, shaft, or other similar components to allow for rotation but prevents the component from moving from side to side. A C-clip fits into a machined groove and acts as a shoulder that holds the part in place snugly. On a lawn mower, a C-clip retaining ring can be found on the wheel axle. It will fit into a narrow groove on the axle to prevent the washer and the wheel from moving.With repeated use, a C-clip can become worn and need replacement. Replacing a C-clip requires removing the old one and installing a new one. While replacing a C-clip is typically a quick process, it must be done with care. Their spring action can launch them when they are being removed or installed, and they are notorious for getting lost. This C-clip is an OEM part sourced directly from the manufacturer and it is sold individually. It is compatible with lawn mowers made by Craftsman, Cub Cadet, Troy-Bilt, Yard Machines, MTD, Huskee, Bolens, and Yard-Man.

This replacement part is a transmission assembly intended for use in lawn mowers. Transmissions play a vital part in stopping and starting the mower engine.If the engine is struggling to start up, it can be due to a malfunctioning transmission. If the user hears unusual noises coming from inside the engine, it can be from this part. Work gloves are always recommended when working near the engine. This is a genuine OEM replacement part manufactured by MTD. This part is sold individually.

This is a replacement transmission cover part for a walk-behind lawn mower or a riding lawn tractor. The transmission helps provide controlled power to the engine and overall machine, so it is important to keep it safe. The cover is a durable plastic that fits around the transmission itself, and is really easy to replace.Over time and through potential mowing over damaging material, the cover can break or crack. This depends on the mower, storage, and the terrain it is used on. For mowers used on normal grass lawns and are stored indoors and out of sunlight might need transmission covers less often than mowers used on silty grasslands or those that are kept out in the sunlight. Replacing the cover is simple, and requires a screwdriver, pliers, a drill, and a pair of durable gloves. The replacement requires some disassembly of the lawn mower and its inner workings.This is a genuine OEM replacement transmission cover. This part is compatible with MTD, Yard Machine, Troy-Bilt, Bolens, Yard Man, and Husky machines, depending on the model. This part is sold separately.

This is a replacement front lever spring. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. This part can be used to replace a broken or defective front lever spring on a variety of outdoor power equipment models. This part helps to adjust the height of the equipment deck to allow it to reach the optimal cutting height for different types of terrain. When working on or near an engine, ensure the equipment is powered off and completely cooled down before starting any repairs. Access to proper tools is required to install this part. It is always recommended that the appropriate safety precautions are adhered to when attempting to fix any power tools or machinery. For more accurate information on how and where to install this front lever spring, the appropriate owner's manual and included diagrams should be referenced.As an authentic replacement part, this front lever spring is suitable for use on several different lawnmower models, log splitters, and chippers manufactured by MTD, Craftsman, Yard Man, Cub Cadet, Husky, Yard Machines, and Troy-Bilt. This is a genuine part made of high-quality, durable materials and is sold individually.

This replacement part is a hex bolt. It is a genuine replacement part made by MTD. Hex bolts are named because they are shaped like a hexagon and are different from the regular circle-shaped bolts. These parts are able to hold other parts secure and in place so that everything can operate as needed. A new hex bolt might be needed if the current ones are damaged in any way. It is possible that these bolts become stripped or lodged in place over time due to normal wear and tear and should be replaced. The repair should be fairly easy, only requiring a screwdriver or pliers if the previous part is stuck. Be sure the engine is completely powered down before beginning this repair. This bolt is sold individually. Be sure to purchase the correct amount as many appliances require more than one. This is a genuine OEM replacement part sourced directly from the manufacturer.

The blade support is found between the blade and the bolt. As its name suggests, it is designed to provide support for the blade to ensure it is secured to the base of the mower deck. It is made of metal and it will need a replacement if it becomes worn or damaged. To replace a blade support or blade spacer, first, the engine needs to be cool. Remove the wire and boot from the spark plug. Tip the mower back on its handle assembly and use a piece of wood or sturdy object to hold the cutting blade in place. Remove the old blade support and blade. When installing the new one, ensure that the blade's sharp edge faces away from the mower deck. Re-thread and torque the bolt between 40 and 50 ft-lbs. This is an original OEM replacement part for lawnmower blade support made by Craftsman, Cub Cadet, Troy-Bilt, Murray, Yard Machines, MTD, Huskee, Bolens, Yard-Man, MasterCut. It is sold individually.

This replacement part is a hex screw. This is a genuine replacement part made by MTD. This type of screw is commonly found in many types of machinery and appliances. Screws are able to keep certain parts stable and connected so that they are secure during use. A new hex screw might be needed if the current one is visibly damaged in any way or missing. It is not uncommon for screws to become stripped down or lodged in place after years of normal use. If this is the case they should be replaced as soon as possible. If the screw is lodged in place, pliers might be required on top of a screwdriver to complete this repair. This part is sold individually and is sourced directly from the manufacturer. This part is a genuine OEM replacement part to ensure proper fit and long-lasting use.

This is a height adjuster knob for walk-behind lawn mowers. It attaches to the height adjuster lever. This component is used to adjust the front wheels on the lawnmower deck. This adjustment allows the user to select the desired cutting height of the grass. This component is made out of a hardened foam material that is easy to grip.If the height adjuster knob falls off of the height adjust lever and will not reattach, it is likely that it will need to be replaced. The height adjuster lever itself is sold separately. The repair person may wish to wear gloves when replacing this part.This component is sourced straight from the manufacturer. It is sold individually and is a genuine OEM part. This height adjuster knob is compatible with walk-behind lawnmowers that are manufactured by the Ryobi, MTD, Yard Machines, Troy-Bilt, Bolens, Yard-Man, Cub Cadet, Craftsman, and Husky brands.

This replacement part is a dust wheel. This is a genuine replacement part made by MTD. This part is used to help prevent wheels from becoming too dusty or dirty when not in use. A new dust wheel might be needed if the current on is missing or damaged. If the dust wheel is torn or unable to close properly, it might be time to replace it. This is a fairy simple repair as the user should be able to slip the dust wheel on over the current wheels. Be sure to purchase the correct amount as these are sold individually. Refer to the user manual for more instructions on how to replace this specific part. This part is sold individually and is sourced directly from the manufacturer. This part is also a genuine OEM replacement part to ensure proper fit.

This dowel pin is a genuine MTD part, sold individually. This dowel pin can be used as a replacement part for a lawn mower, a tiller, or a wood chipper. The purpose of a dowel pin in one of these tools is to serve as a fastening component that affixes two different components to one another by fitting into the cylindrical hole of the dowel pin.The dowel pin can be easily lost or misplaced as it is a small component. The dowel pin can also become stripped. If this occurs, the component should be immediately replaced. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. Always unplug the appliance before performing any kind of repair or replacement. The operator of the appliance should be aware that this component is a genuine OEM replacement part, sourced directly from the manufacturer. It is sold individually. This dowel pin is compatible with the following outdoor appliance brands: MTD, Craftsman, Cub Cadet, Ryobi, Troy-Bilt, Yard Machines, Huskee, Bolens, MasterCut, and Yard Man.

This spring washer has a conical shape with an open center. It has a shape like a traditional washer but is smaller than a typical coiled spring. These washers can handle a larger load than a coiled spring and are used in lawn and garden equipment to cushion heavy loads. Over time, these washers can experience wear and tear which will lead to damage or breakage. When this occurs, the spring washer will need to be replaced.Visually inspect the spring washer for damage like scratches, breaks, and dents. If these occur or the washer is warped, it needs to be replaced. The process involves removing the nut or screw above the washer with a screwdriver or other tool. After accessing the spring washer, it can be removed and a replacement part can be added to the equipment. Reassemble the parts and the equipment should work again.This is a genuine OEM spring washer replacement part that is sold individually. It's sourced directly from the manufacturer. It is compatible with lawnmowers, wood chippers, snowblowers, log splitters, tillers, chainsaws, string trimmers, and edgers by Craftsman, MasterCut, Toro, Turf King, Cub Cadet, Yard-Man, Ryobi, Bolens, Husky, Montgomery Wards, Murray, Huskee, Yard Machines, and MTD.

This replacement part is an adjuster assembly intended for use in lawn mowers. This adjuster assembly allows the user to control the height of the mower's blades, which will adjust the depth of a cut.An adjuster assembly may become stripped or worn down over time, necessitating replacement.This is a genuine OEM replacement part manufactured by MTD. This part is sold individually.

Lawnmowers and other lawn and garden equipment need to be mobile, and that means they need wheels. There are many warning signs that it is time to replace the wheel. For example, if a self-propelling machine struggles to move easily or if a push mower is not operating as smoothly as in the past, it may be that the wheel assembly has failed. The reasons for failures include the materials, the amount of weight put on the wheels, the amount of use, and the type of use. Changing a wheel is simple but requires the appropriate parts. It features a bar tread and roughly 8 in diameter. It should work with all self-propelled and manually operated mowers, as well as the machine and equipment types listed. This authentic OEM complete wheel replacement will work on chipper and shredder machines, edgers, and lawnmowers from the Craftsman, Bolens, and Yard Machines brands. It will also work with Ryobi, MTD, Huskee, and Yardman equipment. It will require the appropriate hardware, which is not included.

This bearing spacer is a genuine MTD part, sold individually. This bearing spacer can be used as a replacement part for a lawn mower. The purpose of a bearing spacer is to line up the bearings of the wheels while situated on the axle of the wheel in between the two bearings.The bearing spacer might have to be replaced at some point within the standard lifespan of a lawn mower if it can no longer separate the bearings from one another. The bearing spacer might suffer damage in the form of stripping, puncturing, tearing, or eroding from general wear and tear, or the component might be lost or misplaced. If this occurs, the bearing spacer should be replaced by this genuine OEM replacement part. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. Always unplug the appliance before performing any kind of repair or replacement.This is an OEM part sourced directly from the manufacturer. It is sold individually. This bearing spacer is compatible with the following outdoor appliance brands: MTD, Craftsman, Cub Cadet, Troy-Bilt, Yard Machines, Huskee, Bolens, and Yard-Man.

This hex screw is a genuine MTD part, sold individually. This hex screw can be used as a replacement part in lawn mowers, snowblowers, tillers, leaf blowers, and wood chippers. The purpose of a screw for one of these outdoor appliances is to serve as a fastening component.This hex screw might have to be ordered as a complete replacement in a hex screw that has been lost, misplaced, or stripped as a result of general wear and tear over long-term use or due to an accidental collision with a hard object. If this occurs, the screw should be removed and replaced by this genuine OEM replacement part.This is a genuine OEM replacement part sourced directly from the manufacturer. It is sold individually. This hex screw is compatible with the following outdoor appliance brands: MTD, Craftsman, Cub Cadet, Troy-Bilt, Murray, Yard Machines, Huskee, Yard Man, and MasterCut.