Parts for Electrolux ECWM3012ASA: Lower Oven Parts

This replacement air fry tray lets your oven's air-fry function hold and crisp foods safely on the oven rack. It restores the manufacturer-intended tray used with Peregrine-series air fry ovens for even airflow and easy cleanup. What it does

• Holds food above the oven surface so hot air can circulate for air-frying and crisping.
• Designed to work with the oven's air-movement system to help promote even browning.
• Replaces a bent, warped, cracked, or missing air-fry tray that prevents proper use of the air-fry feature.
• Helps contain drips and crumbs for easier cleanup when roasting or air-frying.

• One air fry tray (Peregrine) as shown.

• Slide the tray onto the oven rack in the same orientation as the original; no tools usually required.
• Allow the oven to cool and disconnect power before removing the old tray or installing the new one.
• Inspect oven racks and supports for damage before use; do not use if warped or compromised.
• Hand wash or follow manufacturer care instructions; avoid abrasive cleaners that could damage the finish.

This replacement switch restores reliable control of a selected function by opening or closing an electrical circuit inside your appliance. When the original switch wears out, buttons may stop responding or features may not activate consistently.

• Opens/closes an electrical circuit when the button/actuator is engaged
• Routes power or sends a signal to the control or component
• Common symptoms: no response when pressed, intermittent operation, or function won't start
• May show signs of heat damage, loose terminals, or inconsistent "click" feel

• Disconnect power at the breaker before servicing
• Photograph or label wire positions to ensure correct transfer to the new switch
• Move wires one at a time; fully seat connectors on the correct terminals
• Reassemble, restore power, and test the function activated by the switch

This lamp assembly replaces a damaged or nonworking interior refrigerator light to restore safe, reliable illumination. It includes the housing and lamp so you can see contents clearly and check temperatures at-a-glance. What it does

• Provides interior lighting so food and controls are visible when the door is opened
• Replaces cracked or yellowed lens/housing that scatters light or exposes wiring
• Restores a light that stays off due to a broken assembly
• Helps prevent food spoilage by making it easier to find items and verify temperatures

• One lamp assembly (housing with lamp)

• Disconnect power or unplug the appliance before beginning work
• Use basic hand tools; handle glass or lens pieces carefully to avoid breakage
• Check the door switch and wiring harness

This small replacement spacer positions and secures appliance components to maintain correct alignment and fit. Installing the spacer restores proper panel spacing and reduces vibration where a worn or missing spacer causes looseness or rubbing. What it does:

• Maintains the correct gap between panels, trim, or assemblies to ensure parts fit flush
• Keeps components aligned to prevent rubbing, binding, or uneven wear
• Helps reduce vibration and rattling caused by a missing or damaged spacer
• Preserves original part spacing for reliable operation of the surrounding components

• Disconnect power to the appliance before any service to avoid shock or injury
• Remove any trim or fasteners that block access; keep track of screws and small parts
• Match the new spacer's orientation to the original; do not force parts into place

This temperature probe senses oven cavity temperature and sends a signal to the range control so the oven can regulate heat. It helps restore accurate temperature readings for consistent baking and cooking results. What it does

• Senses oven temperature and relays readings to the control board
• Allows the control to cycle heating elements or gas valve for stable temps
• Commonly replaces a failed or intermittent sensor that causes incorrect oven temps
• Resolves symptoms like oven running too hot, too cool, or showing temperature error codes

• Disconnect power to the appliance before starting any repair to avoid shock.
• Handle the sensor and its wiring gently; avoid kinking or pulling on the lead.
• Route and secure the sensor lead the same way as the original to prevent contact with heating elements.

This door hinge secures and guides a refrigerator or freezer door, restoring proper alignment and smooth opening/closing. It replaces a worn or damaged hinge to help stop door sag, rubbing, or uneven sealing. What it does:

• Supports the door at the cabinet, bearing the door's weight and pivoting for opening/closing
• Restores correct door alignment to improve gasket contact and sealing
• Reduces door sag, binding, or scraping against cabinet or shelves
• Helps prevent uneven wear on the door and frame caused by a failing hinge

• Basic mechanical replacement; use proper tools and support the door to prevent dropping
• Power off and remove contents from the door before starting work
• Tighten mounting screws securely but avoid over-torquing to prevent damage

This replacement evaporator fan blade helps circulate cold air inside the freezer or refrigerator compartment to maintain even temperatures and proper cooling performance. A direct-fit replacement when the existing blade is cracked, warped, or missing. What it does:

• Moves air across the evaporator to promote even cooling and frost prevention
• Restores proper airflow when a damaged blade causes noise or reduced cooling
• Helps reduce hot or warm spots inside the compartment
• Quiet, balanced operation when installed correctly

• One replacement evaporator fan blade

• Disconnect power to the appliance before starting any repair
• Typically accessed by removing interior panels in the freezer/refrigerator compartment
• Inspect the fan motor shaft and mounting for damage before installing the new blade

This is a replacement mounting nut used to secure components on compatible Frigidaire appliances. It provides a simple, reliable fastener to replace a missing, damaged, or corroded nut and restore proper part retention. What it does

• Secures panels, brackets, or hardware so parts stay in position during use
• Replaces stripped, rusted, or missing nuts that cause rattling or loose components
• Helps restore proper alignment and safe operation of the affected assembly
• Small fastener used wherever the OEM diagram specifies part 561231207

• One mounting nut (part number 561231207)

• Disconnect power or unplug the appliance before starting any repair
• Use the correct-size wrench or socket to avoid rounding the nut
• Tighten snugly but do not overtighten to prevent thread damage
• If the original nut was corroded, inspect mating threads and replace the bolt/stud if needed

This hex flange nut secures components where a broader bearing surface is needed to resist loosening and distribute load. It fits 10-32 threaded studs and is used on fastened assemblies in appliances. What it does:

• Provides a secure threaded connection for 10-32 screws and studs
• Flange spreads clamping force to reduce panel or bracket damage
• Hex shape allows tightening with a wrench for a reliable hold
• Commonly replaces worn or missing nuts that cause loose panels or rattling

• One hex flange nut

• Use the correct 10-32 screw or stud and hand-start threads to avoid cross-threading
• Tighten with an appropriately sized wrench; do not overtighten to prevent thread or part damage
• Disconnect power and follow appliance safety instructions before servicing
• Replace only like-for-like; confirm size and thread match your application

This factory screw secures components in your appliance, restoring a tight, rattle-free fit. Replace missing or damaged hardware to keep panels, brackets, and trim properly fastened and aligned for safe, reliable operation.

• Secures panels, brackets, trim, or internal components to the chassis
• Replaces lost, rusty, stripped, or cross-threaded screws
• Helps eliminate looseness, gaps, and vibration/rattling
• Common signs: loose/misaligned panels or trim, rattling noises, missing or rounded screw heads

• Disconnect power (and shut off gas if applicable); allow the unit to cool completely
• Match to the original location and replace one at a time to maintain alignment
• Hand-start to prevent cross-threading; tighten snugly—do not overtighten
• Use light torque when threading into plastic or thin sheet metal