Parts for Ge PT9200SL3SS: Lower Oven Parts

Fix F9 error codes and overheating control panels with this cooling fan motor. Restores airflow to protect internal components. Moderate DIY repair.

Oven won't heat or shuts off during use? This high limit switch cuts power when temperatures exceed safe levels. Moderate DIY repair for wall ovens.

Left-hand rack guide for electric wall ovens. Guides the oven rack smoothly in and out. Replace if cracked, broken, or missing for proper rack support.

Replace your worn, warped, or missing oven rack. This gray rack slides into standard wall oven rack guides for holding cookware during baking and roasting.

Rack slide assembly for wall ovens. Mounts inside the oven cavity to support and guide oven racks. Replace if slides are bent, damaged, or missing.

Right-hand rack guide for wall ovens. Supports and aligns oven racks for smooth sliding. Replace if cracked, broken, or missing to restore proper function.

Seals the back lamp assembly in your wall oven to prevent heat loss and moisture intrusion. Replace if cracked, brittle, or no longer sealing properly.

If your wall oven won't heat properly or takes too long to preheat, the lower bake element may be burned out. This repair restores even heating.

Fix F2 error codes and inaccurate oven temperatures by replacing a faulty temperature sensor. Simple 15-minute DIY repair with basic tools.

Retainer bolt secures internal components and panels in your range or wall oven. Replace if bolt is stripped, missing, or causing loose assemblies.

Restores bright interior lighting in your oven or range. Replace when bulb burns out to clearly see food and monitor cooking progress. Verify G9 base fit.

Halogen light bulb assembly for your oven. Replace when light dims, flickers, or burns out to restore interior visibility. Verify fit with your model.

This SPDT high-amp switch controls high-current circuits by switching one input between two outputs, restoring proper electrical control in affected appliance functions. Built for high-load switching where reliable on/off selection is required. What it does:

• Directs high-current power from a single input to one of two outputs (single-pole, double-throw action)
• Replaces worn or failed selector/limit-style switches that cause intermittent or no power to a circuit
• Commonly used where a high-amp, durable switching contact is required to complete a function
• Helps stop symptoms like intermittent operation, failure to switch between states, or no power to the controlled circuit

• One SPDT high-amp switch (WB24T10160)

• Disconnect power to the appliance before inspecting or replacing the switch
• Verify wiring locations and take a photo before removal for correct reconnection
• Use proper tools and avoid touching energized contacts;

This rail support secures an oven rack guide so the rack slides smoothly and stays aligned. It restores proper rack movement and prevents sagging or binding for safer, more reliable oven use. What it does

• Holds and aligns the oven rack guide so racks slide in and out smoothly
• Replaces a cracked, broken, or worn support that causes rack wobble or misalignment
• Prevents racks from tipping or catching when pulled forward
• Works with the oven's rack system to maintain stable cooking and loading

• One rail support

• Disconnect power to the appliance before starting any repair
• Typically accessed from the oven interior; remove racks to reach the support
• Install with basic hand tools; do not force parts into place—ensure correct orientation

Replaces the lower exterior trim on your wall oven door. Restores a secure fit and clean appearance where original trim is cracked, bent, or missing.

A receiver hinge that secures and supports an oven door hinge pin to keep the door aligned and operating smoothly. Replaces a worn or broken receiver to restore proper door fit and movement. What it does

• Accepts and retains the oven door hinge pin so the door opens and closes correctly.
• Supports door weight to prevent sagging or uneven alignment.
• Helps the door latch and seal properly for safe, consistent operation.
• Commonly replaced when the door drops, rubs, or will not stay closed.

• One receiver hinge

• Disconnect power to the appliance before servicing to avoid shock or injury.
• Remove the oven door or access panel per the service manual for safer installation.
• Use basic hand tools; check hinge pins and mating hardware for wear and replace if needed.

The Probe Thermistor is an OEM replacement part for GE wall ovens and ranges. Located inside the oven cavity, this temperature-sensitive probe precisely monitors interior heat to safeguard against overcooking.

Causes of a faulty thermistor involve exposure to excessive cooking temperatures, moisture infiltration from spills or steam, or basic failure due to old age.

Symptoms of an inadequate probe thermistor include:

• Inaccurate temperature readings and baking inconsistencies
• Oven temperature exceeding desired setting risking fire

This OEM GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This is an electrical relay used in ranges and ovens to control power to specific components such as heating elements or fans. It switches circuits on and off in response to signals from the control board. Replace this relay if a burner or oven element fails to heat, heats intermittently, or if the relay is visibly burned or damaged.

The Wall Oven Capacitor Motor is an OEM part for GE wall ovens. Located inside the oven cavity, this motor is responsible for turning the convection fan which circulates hot air for even baking and roasting. 

Symptoms of a bad capacitor motor include:

• Inability to select convection bake or roast features 
• Uneven cooking results 
• Lack of air circulation inside the oven
• Strange noises coming from the fan/motor area
• The convection fan not turning on 

Causes of failure can be wear over time, damage from debris inside the oven, or occasional voltage fluctuations which can degrade motor components.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Wire harness for oven temperature probe. Connects probe sensor to control board. Replace if wires are frayed, connectors are damaged, or harness is broken.

Replace the plunger harness wire in your wall oven. This wire harness connects to the door latch plunger assembly. Order now if damaged or worn.

Replacement mounting screw for cooktops and ranges. Secures cooktop components to the frame. Replace if screw is stripped, missing, or damaged.

Replacement washer for ranges and ovens. Used to secure components and provide even fastening. Replace if cracked, worn, or missing during repairs.

Ribbon connector assembly that links control boards to user interface components. Needed when the existing flat flex cable is damaged, torn, or worn.