Lowe's Parts

Replace your cracked or worn lawn mower grass collection bag. This hard-top grass bag attaches to the rear discharge to collect clippings during mowing.

Hex screw fastener for lawn tractors and outdoor power equipment. Secures components throughout the machine. Replace if stripped, overtightened, or missing.

Tap screw for lawn mowers and tractors. Secures panels, guards, and components. Replace if stripped, rusted, or missing to restore proper assembly.

Square key for lawn tractors, tillers, and snow blowers. Secures shafts and pulleys. Replace if worn, sheared, or missing to restore proper assembly.

If your lawn tractor has vibration or won't drive properly, the U-joint may be worn. Connects rotating components in the drive system.

This amp fuse is a genuine MTD part, sold individually. This amp fuse can be used as a replacement part in a lawn mower. The purpose of the amp fuse in a lawn mower is to protect the lawn mower from potential voltage issues and failures that might occur during the general use of the appliance.The amp fuse in a lawn mower might need to be replaced if the component suffers damage or blows out after protecting the appliance from an electrical current voltage overload. If the amp fuse has blown or has suffered damage from general wear and tear with long-term use, the amp fuse should be removed and replaced by this genuine OEM replacement part in order to guarantee continued safe use of the lawn mower by the operator. Always unplug the appliance before performing any kind of repair or replacement.This component is a genuine OEM replacement part sourced directly from the manufacturer. It is sold individually. This amp fuse is compatible with the following outdoor appliance brands: MTD, Cub Cadet, and Troy-Bilt.

Insulator plate for lawn tractors and riding mowers. Mounts between engine components to provide heat insulation and proper spacing. Replace if cracked or worn.

Replacement rear discharge flap assembly for walk-behind lawn mowers. Installs at the rear deck opening to shield against debris. Needed when cracked or torn.

This genuine OEM part is a compression spring for a lawnmower. The compression spring is the spring that holds the mower deck onto the lawnmower. Over time, the compression spring can become degraded due to excessive wear and tear. If it is no longer securing the mower deck, it will need to be replaced. Luckily, replacing this part is a relatively simple process.To replace the spring, make sure the mower deck is set to the lowest position. Locate the old retainer spring and pull it out and away from the mower. Once removed, slide the new spring into its proper position. Make sure it fits tightly, and the mower deck is secured. Once secured, power the mower to see if the spring stays in place during operation. If it does, then the installation was a success. This replacement part is sold individually and is compatible with MTD brand lawnmowers.

Small metal washer that installs with screws and bolts throughout lawn mowers and outdoor power equipment. Replace if cracked, worn, or missing.

Flat washer for lawn tractors and mowers. Replace when worn, damaged, or lost to ensure proper hardware fit and secure assembly. Verify compatibility.

Small metal washer for lawn mowers and outdoor power equipment. Replaces cracked, worn, or missing washers. Ensures proper spacing and assembly.

Replace a bent, damaged, or broken tiller shaft causing poor tilling performance or unusual vibration. Direct fit for multiple rear-tine tiller models.

Shoulder screw fastener for lawn tractor internal machinery. Replace if screw is stripped, missing, or no longer secures components properly.

This is a thrust bearing. The thrust bearing is positioned between the lawn mower's spindle and front axle and serves to reduce friction during use. This part makes shifting between different speeds much easier. A worn-out thrust bearing will have more room between the rollers on the outside of the bearing. This movement will cause the bearing to move more than usual. When the bearing goes bad, the driver may notice rattling, squeaking, or other noises coming from the machine. These noises can be more prevalent when the clutch pedal is engaged. To replace the thrust bearing, first, the clutch must be removed from the lawn mower. On the bottom of the driveshaft, there is a bolt and washer that need to be removed. Wedge and move the clutch, allowing it to work its way down the driveshaft, then remove it. There is a bearing retainer clip and three bolts that will enable the thrust bearing to be removed. Repeat the steps in reverse after installing the new component.This product is a genuine OEM MTD part sourced directly from the manufacturer. The part is sold individually and not available with any other components. This product is compatible with MTD and Cub Cadet products.