Parts for Ge GTE18ETHDRBB: Machine Compartment Parts

This hex-head screw secures dishwasher panels, brackets, and internal hardware so parts stay tight and rattle-free. Replace missing or stripped fasteners to restore a secure fit and reliable operation.

• Fastens panels, brackets, and other dishwasher components to the tub or frame
• Replaces a missing, stripped, or corroded screw that no longer holds securely
• Helps eliminate vibration and rattling caused by loose hardware
• Maintains proper alignment and secure mounting of parts during operation

• Disconnect power and shut off water supply before servicing
• Keep track of fastener locations and orientation for correct reassembly
• Start threads by hand; use an appropriate nut driver or socket to tighten
• Tighten snugly—do not overtighten, especially when threading into plastic

This access cover is the replacement panel that protects and hides internal refrigerator components while allowing access when service is needed. It restores a finished appearance and keeps wiring and parts shielded from spills and debris. What it does

• Covers and protects internal components behind the refrigerator control/ice area.
• Helps prevent dirt, moisture and foreign objects from contacting wiring and electronics.
• Allows service access to underlying parts when removed for diagnostics or replacement.
• Damaged or missing covers can expose components and lead to rattling or moisture issues.

• One access cover panel

• Disconnect power to the appliance before starting any service.
• Remove screws or clips holding the old cover; note locations for reassembly.
• Handle plastic tabs carefully to avoid cracking during removal or installation.
• Tighten fasteners snugly but do not overtighten to prevent damage.

This wiring harness assembly connects control and electrical components to restore proper signal and power routing within the appliance. Use it to replace damaged or faulty wiring that causes intermittent or failed component operation. What it does

• Routes power and control signals between the control board and major components.
• Replaces frayed, burned, or broken wires to eliminate shorts or open circuits.
• Helps resolve symptoms like no power to components, intermittent operation, or controls that don't respond.
• Maintains correct connector fit and secure electrical connections for reliable performance.

• One wiring harness assembly as shown.

• Disconnect all power before starting any repair to avoid shock or injury.
• Compare the new harness to the original for correct connector types and lengths before installation.
• Route and secure the harness away from sharp edges, moving parts, and heat sources.

Size: 10-16 ab.

This condenser kit replaces a refrigerator's damaged or corroded condenser to help restore proper heat dissipation and improve cooling efficiency. It's the direct-fit condenser assembly used in compatible GE refrigeration units. What it does:

• Moves heat away from the refrigerant so the system can cool properly
• Commonly replaced for visible coil damage, corrosion, or bent fins
• Can address symptoms such as reduced cooling performance or longer run cycles
• Works with the existing refrigeration loop when installed correctly

• One replacement condenser kit

• Disconnect power to the appliance before starting any repair
• Access typically requires removing the back or lower rear service panel
• Inspect mounting hardware and electrical connections during installation; follow OEM instructions

The Overload Ptcr Combo is an OEM part for GE refrigerators. It is responsible for regulating the electrical current flowing to the compressor. It helps prevent damage to the compressor and extends its lifespan.

A bad overload ptcr combo can be caused by power surges, electrical malfunctions, or normal wear and tear over time.

Symptoms of a bad overload ptcr combo include:

• The refrigerator not cooling properly.
• The compressor making unusual noises or not running at all.
• Excessive heat around the compressor area.
• Frequent tripping of the circuit breaker.

Replace your worn-out or damaged overload ptcr combo with this genuine OEM part and ensure the efficient and reliable operation of your refrigerator's compressor. This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

This is a grommet and it is intended for use on refrigerators and freezers. This is a genuine replacement part made by General Electric. A new grommet might be needed if the current one is visibly worn out or damaged in any way. If there are noises from vibration coming from the lower back area of the fridge there might be need for a new grommet. This is an OEM part sourced directly from the manufacturer, and it is sold individually. It is compatible with refrigerators and freezers, or units with a compressor and is made by General Electric.

This condenser support is the replacement mounting bracket that secures the refrigerator condenser coil and helps keep the unit stable behind the lower access panel. It restores proper condenser positioning for reliable cooling performance. What it does:

• Holds the condenser coil in the correct position to prevent contact with other components
• Reduces vibration and rattling from a loose condenser assembly
• Helps maintain proper airflow behind the cabinet when installed correctly
• Can prevent wear to nearby components caused by a displaced condenser

• Disconnect power before servicing and work with the appliance unplugged to avoid shock
• Access typically requires removing the refrigerator's lower access panel or rear service panel
• Basic hand tools are usually sufficient; keep fasteners for reuse unless damaged
• Handle edges carefully; inspect surrounding parts and wiring before reassembly