Parts for Ge GTE21GTHGWW: Machine Compartment Parts

Electronic defrost control board that manages the refrigerator's timed defrost cycles to reduce evaporator frost buildup and help maintain steady cooling. Replacing a failed control restores normal automatic defrost operation. What it does:

• Regulates defrost cycle timing and duration to prevent excessive ice on the evaporator
• Stops regular cooling temporarily during defrost to melt accumulated frost
• Common symptom: excessive frost or ice buildup on evaporator coils or in the freezer compartment
• Other symptom: temperature fluctuations or the unit running continuously because defrost cycles aren't happening

• Always disconnect power to the appliance before servicing to avoid electrical shock
• Access typically requires removing the refrigerator's control or back access panel — keep screws and small parts organized
• Match wire harness connectors and mounting holes; do not force connectors or bend pins

The Drier is an OEM component specifically designed for GE combination refrigerator-freezers. Absorbing moisture, its treated silica particles buffer humidity within refrigerant lines. Proper drying sustains energy-efficient performance while preventing corrosion.

Causes of a faulty drier commonly relate to saturation reducing capacity. As desiccant degrades, water passes into closed system compressors requiring change. 

Symptoms of a bad drier involve:

• Frost and ice buildup impairing cooling  
• Puddling around evaporator evidencing leaks
• Higher operating costs from impaired efficiency

Causes of a bad drier involve typical saturation shortening drying cycles. Cracks release desiccant particles risking blockages necessitating timely replacement.

This OEM GE part is also compatible with some Hotpoint, RCA, and Frigidaire combination units. Replace to retain steady humidity management protecting components and maximizing freshness years of operation.
 

This condensate auxiliary drain tray catches and directs refrigerator drain water to the main drain, helping prevent minor leaks and moisture buildup under the unit. It's a small replacement tray used with the appliance's evaporator/condensate system. What it does:

• Collects condensate and channels it to the refrigerator drain system
• Helps reduce water pooling and moisture under the cabinet or inside kickplate areas
• Supports proper evaporator/defrost drainage to avoid misdirected runoff
• Can resolve symptoms like water dripping or minor leakage near the base of the fridge

• One condensate auxiliary drain tray

• Disconnect power to the appliance before accessing internal panels
• Remove the appropriate access or kick panel to reach the drain area; retain fasteners for reinstallation
• Seat the tray into the existing mounting location and secure any clips or screws as originally installed
• After installation, restore power and run a short defrost or pour a small amount of water into the evaporator drain to confirm proper flow

The Compressor Overload Protector is an OEM component specifically designed for GE refrigerators. It plays an important safety role by protecting the compressor from damage. 

The overload protector works to monitor compressor temperature and electrically disconnect power to the compressor if it exceeds safe operating limits. This prevents overheating that could compromise refrigeration system integrity.

Causes of a bad overload protector include failing sensors, breaking off mounting tabs, or damage from physical impact over time.

Symptoms of a bad overload protector are:

• The refrigerator fails to cool and the compressor does not run  
• Abnormal compressor buzzing or rattling noises occur
• Diagnostic codes or error messages indicate compressor issues

This genuine OEM GE replacement ensures the compressor functions properly without overheating. It also helps extend the lifespan of major components. Compatible with Hotpoint, RCA, and Kenmore models as well.
 

Size: 8-32 t. Includes 12 screws.

This is a replacement mounting screw used to secure components and trim on compatible GE appliances. Installing the correct screw restores secure fits and prevents rattling or loose parts for reliable operation. What it does

• Secures panels, brackets, trim pieces or components in place
• Prevents vibration-related noise by keeping parts tight
• Restores proper alignment where a lost or damaged screw caused looseness
• Matches OEM fastening point to maintain fit and function

• One mounting screw as shown

• Use the matching driver and size to avoid stripping the head or threads
• Tighten until snug; avoid over-torquing which can damage parts or plastic mounts
• Disconnect power or follow appliance-specific safety steps when accessing internal areas

The R600 Process Valve with Red Cap is an OEM part for GE refrigerators. It regulates the flow of refrigerant within the cooling system, ensuring proper cooling and temperature control.

A bad process valve can occur due to wear and tear, refrigerant leaks, or mechanical failure. If you notice symptoms such as inadequate cooling, excessive frost buildup, or unusual noises coming from the refrigerator, it may indicate a faulty or malfunctioning process valve.

Symptoms of a bad process valve include:

• Inadequate cooling or inconsistent temperature control
• Excessive frost buildup in the freezer
• Unusual noises coming from the refrigerator

Restore your refrigerator by replacing the faulty process valve with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.