Parts for Lg LRSPS2706V/00: Machine Compartment Parts

This is a replacement drain tube assembly that directs water from the appliance tub to the drain pump or household drain, helping restore proper water removal and reduce leaks. It's a direct-fit service part used in the drainage system. What it does:

• Channels wastewater away from the tub to the drain pump or drain line
• Helps prevent pooling or slow draining caused by a damaged or disconnected tube
• Restores a sealed path to reduce leaks at the tub-to-pump connection
• Suitable when the original drain tube is cracked, split, collapsed, or leaking

• One drain tube assembly as shown

• Disconnect power and water before beginning any repair to avoid shock or flooding
• Inspect and clean mating surfaces and clamps; replace clamps if corroded or damaged
• Ensure correct routing and secure connections to prevent kinks and leaks

This insulated duct assembly cushions and channels airflow while reducing noise and heat transfer. It restores proper ventilation and helps maintain efficient operation and quieter performance. What it does:

• Replaces a damaged or worn insulated duct to restore correct airflow routing
• Reduces vibration noise and minimizes heat loss from the airflow path
• Helps prevent air leaks that can cause reduced performance or localized heating
• Fits where the original insulated duct was installed and works with the appliance's venting system

• Disconnect power and any gas supply before servicing
• Inspect surrounding seals and fasteners; replace any damaged clips or tape
• Follow OEM instructions for routing and securing the duct to avoid pinching

The Ice Bin is an OEM part for LG refrigerators. This bin is responsible for storing ice produced by the ice maker.

Causes of a bad ice bin include wear and tear from years of use, damage from falls or impacts, or stresses from repeated opening and closing of the freezer door. 

Symptoms of a bad ice bin include:

• Leaks or drips from within the freezer compartment
• The bin not fitting or sitting securely in place

This OEM LG part is also compatible with some Kenmore models.

This drawer tray assembly is the replacement storage tray that supports and contains items inside a refrigerator drawer, restoring proper drawer function and organization. What it does

• Replaces a cracked, warped, or broken drawer tray so items sit level and the drawer closes smoothly
• Restores a sealed surface that helps contain spills and prevents items from shifting
• Helps eliminate scraping, catching, or sticking during drawer use
• Fits into the existing drawer housing and works with the factory slide mechanism when the original tray is removed

• One drawer tray assembly as shown

• Installation typically requires removing the drawer and snapping or sliding the tray into the drawer frame
• Handle the part carefully to avoid cracking plastic; inspect mounting rails and clips for damage before installing
• If clips or rails are damaged, replace those components as well—this part replaces only the tray
• Disconnect power and remove stored items from the drawer before starting work

This upper drawer tray assembly supports and contains items in the refrigerator's top drawer, restoring a stable surface and helping prevent spills or sagging. Designed to replace a cracked, warped, or damaged upper drawer tray. What it does:

• Provides a flat, stable base for the upper refrigerator drawer so items sit level
• Keeps small items contained to reduce shifting and spills inside the drawer
• Restores proper drawer alignment and smooth sliding when a broken tray causes binding
• Helps prevent moisture pooling when the original tray is cracked or distorted

• Unplug the refrigerator or disconnect power before servicing to avoid electrical hazard
• Remove food and slide out the drawer fully to access and replace the tray
• Handle the replacement part carefully to avoid scratching or chipping; reassemble in reverse order
• If you encounter resistance or misalignment after installation, double-check tray seating and drawer rails

This shelf assembly replaces a damaged or missing refrigerator shelf to restore stable storage and organization. It provides a durable, easy-to-install surface for holding food, containers, and other items in the fresh-food compartment. What it does

• Provides a flat, stable surface for storing food and containers inside the refrigerator
• Replaces cracked, chipped, or warped shelves that cause items to tip or slide
• Restores proper spacing and organization to improve usable storage area
• Compatible with factory shelf supports and slides to sit securely in place

• One refrigerator shelf assembly (exact configuration as shown)

• Remove all food and loose items before installing; handle glass edges carefully
• Slide the shelf into existing tracks or rest on supports until it sits level and secure
• If shelf uses clips or brackets, confirm alignment before applying pressure
• If damaged supports or clips are present, replace those parts to ensure a safe fit

A replacement freezer shelf assembly that restores storage support and organization inside the freezer compartment. Replaces a cracked, warped or missing shelf so frozen items sit level and are easier to access. What it does:

• Provides a sturdy surface to hold frozen foods and containers
• Replaces shelves that are cracked, bent, or no longer supporting weight
• Helps restore proper airflow and organization inside the freezer compartment
• Useful when shelf clips or mounting points are damaged or worn

What's included: One freezer shelf assembly Install notes:

• Unplug the appliance or shut off power before starting work
• Remove contents from the shelf and surrounding area to avoid breakage
• Handle with care if the shelf includes glass; wear gloves and eye protection
• Basic tools may be needed to release or secure mounting clips

This freezer shelf assembly restores a sturdy, level surface for food storage in your freezer. Replace a broken or missing shelf to maximize usable space, keep items organized, and maintain safe, easy access to stored foods. What it does:

• Provides a stable, level platform for freezer storage
• Replaces cracked, broken, sagging, or missing shelf panels
• Helps items stay organized and prevents tipping or shifting
• Can resolve issues with a shelf not seating or staying in its rails when the original is damaged

• 1 freezer shelf assembly

• Disconnect power and remove contents before servicing
• Lift out or unclip the damaged shelf; install the new shelf in the same orientation and position
• Ensure the shelf is fully seated in side rails or rear slots; do not force into place
• Distribute weight evenly before loading items

This vegetable tray assembly replaces a damaged or worn crisper drawer to restore storage for fresh produce and help keep it organized in your refrigerator. Durable molded construction supports fruits and vegetables while sliding into the cabinet. What it does:

• Replaces a cracked, chipped, or broken crisper/vegetable drawer that won't hold produce
• Restores a smooth sliding drawer action when the tray and guides are intact
• Provides a dedicated, contained space to keep fruits and vegetables organized
• Helps prevent produce from spilling onto lower shelves

• One vegetable/crisper tray assembly

• Unload produce and remove the old tray before installing the replacement
• Inspect drawer rails/guides for damage and clean tracks of debris for smooth operation
• No special tools typically required; handle glass or plastic components carefully to avoid damage

This Tray Cover Assembly replaces a cracked or damaged plastic cover that protects and secures the appliance tray, restoring proper fit and appearance. It provides a simple, direct replacement for worn or broken covers. What it does:

• Covers and protects tray contents from debris and spills
• Keeps the tray seated and aligned to prevent rattling or shifting
• Replaces cracked, warped, or broken covers that no longer stay in place
• Helps restore proper function and appearance after impact or wear

• One tray cover assembly

• Disconnect power or unplug the appliance before starting any repair
• Remove the old cover by releasing retaining clips or screws as applicable; handle plastic parts gently to avoid breakage
• Align the replacement cover and snap or fasten it into place until all clips engage

This rear cabinet cover replaces a damaged or missing TV back panel to protect internal electronics and restore the set's finished appearance. It provides a secure mounting surface and helps keep dust and debris out of the chassis. What it does

• Shields internal circuit boards, power supply and connections from dust, impact and accidental contact
• Restores proper alignment and attachment points for the TV chassis and external connectors
• Eliminates rattles or loose fit caused by cracked or broken mounting tabs
• Helps maintain proper ventilation paths around internal components when installed correctly

• Unplug the TV and place on a soft, protected surface before starting; handle cover edges carefully to avoid cuts.
• Keep and reuse original screws and any attached hardware unless replacements are specified.
• Align mounting tabs and connectors before tightening fasteners; do not force or overtighten to avoid breaking plastic tabs.
• If internal access is required, refer to the TV's service manual; do not touch exposed boards while the set is powered.

This freezer door foam assembly replaces the insulating foam inside a freezer door to help restore proper door sealing and temperature control. It reduces cold loss and helps prevent frost build-up around the door. What it does:

• Replaces deteriorated or damaged door insulation to improve thermal barrier performance
• Helps the door form a tighter seal, reducing warm air infiltration and temperature swings
• Limits frost and ice buildup that can result from poor insulation
• Supports more consistent freezer temperatures and can reduce overworking of the compressor

• Disconnect power to the appliance before beginning any repair
• Installation typically requires removing the inner door panel; save screws and handle components carefully
• Handle foam gently to avoid tearing; align and seat the foam evenly within the door cavity

This replacement door gasket assembly restores the airtight seal around a refrigerator door to help maintain stable temperatures and reduce frost and moisture buildup. Use it to replace torn, warped, or leaking gaskets and improve sealing. What it does:

• Seals the refrigerator door to keep cold air in and warm air out.
• Helps reduce frost and moisture inside the compartment.
• Commonly replaced when the gasket is cracked, warped, compressed, or allows noticeable air leaks.
• Installing a good seal can help the appliance maintain set temperatures more consistently.

• Disconnect power and remove food/media from the door area before starting.
• Clean the door channel and gasket seating area to ensure proper adhesion/seating.
• Align the gasket evenly and engage all retaining tabs or adhesive per the original orientation.

This replacement door basket restores storage on your refrigerator door, keeping bottles and small containers organized and secure. Ideal when the original bin is cracked or missing, it helps prevent spills and maximizes usable door space. What it does:

• Holds bottles, jars and small food containers on the refrigerator door
• Keeps items organized and prevents them from falling when the door opens
• Replaces cracked, warped or broken door bins to restore full door functionality
• Snaps into existing door shelf supports for a secure fit

• Empty the door shelf and remove the damaged bin before installing the replacement
• Align the bin with the door shelf supports and snap it firmly into place
• No special tools typically required; handle glass or plastic containers with care
• If working near electrical components or lights, unplug the appliance or switch off power as a safety precaution

This name plate is the exterior emblem that mounts to the appliance's front panel. It replaces a missing, cracked, or faded badge to restore a clean, factory look and cover the designated trim area.

• Attaches to the outer panel to display brand/series identification
• Restores a finished appearance where the original emblem sits
• Direct replacement for a lost, damaged, or worn badge
• Typical symptoms: missing emblem, loose or broken tabs, peeling, or discoloration

• Disconnect power before servicing the appliance
• Carefully remove the old emblem; release any tabs from behind or peel away remaining adhesive
• Clean and dry the mounting surface; remove all residue for best fit
• Align with the recess/holes and press evenly until fully seated

Restore a tight seal on your refrigerator door with this door gasket assembly. A fresh, flexible gasket helps keep cold air in and warm air out, maintaining proper temperatures and reducing frost and moisture around the door.

• Creates an airtight seal between the refrigerator door and cabinet to maintain consistent cooling
• Helps reduce condensation, frost, and warm spots near the door
• May help if the door won't close fully, the gasket is torn or warped, or temperatures fluctuate
• Magnetized edge engages the cabinet for a secure seal when the door is closed

• Unplug the refrigerator before beginning; wear cut-resistant gloves
• Soften the gasket in warm water or with gentle heat to ease installation and improve fit
• Remove the old gasket carefully, noting retainer/channel orientation; press new gasket fully into the track
• Check door alignment and perform a dollar-bill test around the perimeter to confirm a uniform seal

This refrigerator door bin replaces a broken or missing shelf on the inner door, restoring organized, easy-to-reach storage. It seats into the molded tabs on the door liner to hold items securely and maximize usable space.

• Holds bottles, jars, and condiments on the door to free up shelf space
• Replaces cracked plastic or broken locking tabs
• Addresses a bin that won't stay seated, sags, or wobbles
• Ideal when a bin is missing or too damaged to safely store items

• Remove the old bin by lifting up to release it from the retaining tabs, then pull out
• Align the new bin's tabs/hooks with the slots on the door liner
• Press down/slide into place until fully seated and level
• Verify the bin is secure before loading; distribute weight evenly to prevent damage

This home bar case is a replacement door bin that restores secure storage and easy access to beverages and small items in the refrigerator door. It fits into the refrigerator's home bar area to keep contents organized and contained. What it does:

• Holds and secures bottles, cans and small containers in the refrigerator's home bar area
• Replaces cracked, broken or worn door bins that no longer latch or hold items safely
• Prevents items from shifting or falling when the door is opened or closed
• Restores the original storage shape and containment of the door shelving system

• One home bar case (door bin)

• Replacements are usually snap-in; remove the old bin by lifting or sliding per the refrigerator's door shelf design
• Handle parts carefully to avoid scratching the door or interior trim during removal/installation
• Disconnect power only if working near electrical controls or lights; otherwise, no major disassembly is typically required

The Hinge Assembly, Upper is an OEM replacement part for LG refrigerators. This upper hinge assembly works together with the center hinge to provide balanced support and motion to the refrigerator doors.  

Causes of a bad upper hinge assembly can include long-term wear and tear, accidents, or overloading the doors with excessive weight. Over time, the hinges may become misaligned or components can weaken.

Symptoms of a bad upper hinge assembly include:

• Gaps appearing along the top edge of the door seal
• Doors no longer closing flush or sealing properly  
• Difficulty opening and closing the doors
• Noises or creaking coming from the hinge area

This OEM LG part is also compatible with select Sears/Kenmore brand models. 

This upper hinge assembly secures and pivots the refrigerator door, restoring proper alignment and smooth opening/closing. Durable replacement for worn or damaged upper door hinge hardware to help prevent sagging and gaps. What it does:

• Supports the top of the refrigerator door and provides the pivot point for opening and closing
• Restores proper door alignment to help maintain an even seal and prevent cold air loss
• Eliminates squeaks, binding, or resistance caused by worn hinge components
• Helps prevent door sag and uneven gaps that can interfere with operation

• Unplug the appliance and remove food from the door shelves before beginning work
• Support the door (use a second person or a block) while removing and installing the hinge to avoid dropping or damaging the door
• Keep fasteners and any bushings/towels organized; some models reuse original screws or pins
• Adjust hinge screws per the manufacturer's instructions

This hinge lever mounts on the refrigerator door hinge to guide door movement and closure, helping the door seal properly. Replacing a worn or broken lever restores smooth operation and consistent sealing.

• Guides hinge motion so the door opens and closes smoothly
• Helps maintain door alignment for a reliable gasket seal
• Replace if the lever is visibly cracked, worn, or deformed

• Disconnect power and support the door to prevent injury or damage
• Remove the hinge cover and fasteners; note the lever's orientation before removal
• Install the new lever in the same position and reassemble the hinge components
• Adjust hinge per model procedures if needed

This hinge cover assembly replaces a damaged or worn trim piece that protects and conceals the door hinge. It restores the washer/dryer's finished appearance and helps keep the hinge area free of debris. What it does:

• Covers and protects the door hinge from dirt, lint, and physical damage
• Keeps the hinge area looking finished and prevents snagging on clothing
• Helps maintain proper clearance around the door hinge for smooth opening and closing

• Disconnect power and water supply before starting repairs.
• Support or remove the door per the appliance service instructions to access hinge trim.
• Typically secured with screws or clips; use basic hand tools and avoid overtightening.
• Replace/repair the hinge hardware before installing the cover.

This evaporator assembly replaces the sealed evaporator coil and housing that cools the freezer compartment and helps maintain proper low temperatures. Restores cold-air circulation and supports frost-management in frost-free refrigerators. What it does:

• Absorbs heat from the freezer compartment so refrigerant can carry heat away
• Works with the evaporator fan to circulate cold air through the cabinet
• Failing or damaged evaporators can cause warm/freezer not cold, frost buildup, or excessive frost/ice on coils
• Helps stop drip or pooling water from improper defrost when the evaporator assembly is functioning

• One evaporator assembly

• Service may require access to the sealed refrigeration system; follow manufacturer repair procedures
• Handle carefully to avoid puncturing the coil; damaged coils require sealed-system service
• Disconnect power before servicing and wear appropriate PPE when accessing internal components

A small retaining pin used to secure moving parts and keep components aligned for smooth operation. Replacing a worn or broken common pin can stop rattling and restore proper fit between linked parts. What it does:

• Holds or aligns two parts together so they move correctly and stay in position
• Helps prevent rattling, looseness, or parts slipping out of place
• Works as a simple mechanical fastener—no electronics involved

• One common pin

• Disconnect power to the appliance before beginning any service
• Keep track of small parts; lay out components in order to aid reassembly
• May require removal of trim or a hinge/retainer to access the pin—use basic hand tools
• If the pin is difficult to seat, do not force; inspect mating parts for damage

This PTC thermistor assembly senses temperature changes and sends that signal to the appliance control so the system can regulate heating or cooling. It's a direct-replacement part that restores accurate temperature feedback for proper cycle control. What it does:

• Measures temperature and provides a resistance/voltage signal to the control board
• Helps the appliance maintain correct operating temperature and cycle timing
• Can cause long run times, poor temperature control or error codes when failing
• Works as a monitored safety/feedback device in the appliance's thermal system

• One thermistor assembly (PTC) as shown

• Disconnect power before servicing to avoid shock or damage
• Handle the sensor and wiring carefully; avoid bending or stressing the probe or connector
• Reconnect wiring securely and route harnesses away from moving parts and heat sources

This compressor damper is a vibration-isolating mount that sits between the sealed-system compressor and the chassis. It cushions the compressor to reduce noise, limit vibration transfer, and help keep refrigerant lines from being stressed.

• Isolates the compressor from the frame to absorb start/stop shock and vibration
• Helps reduce humming, rattling, or buzzing from the back/bottom of the appliance
• Replaces a damper that's cracked, flattened, hardened, or missing
• Can help if the compressor rocks or the unit vibrates excessively

• Disconnect power and pull the unit forward for access; remove rear/service panel if present
• Support the compressor to relieve load on the mounts before removing fasteners
• Match orientation; transfer any sleeves/spacers from the old damper to the new one
• Ensure the compressor sits level and that tubing is not strained before restoring power

This small stopper installs in the refrigerator to limit the travel of a moving component and keep it securely in place. Replacing a broken or missing stopper prevents over-extension and helps maintain smooth, aligned operation.

• Limits the range of motion for a door, bin, or drawer to prevent over-opening or accidental removal
• Helps keep interior components aligned and operating smoothly
• Replace if cracked, missing, or deformed
• Common symptoms: drawer or bin slides out too far, door swings past normal range, or a broken plastic stop is found

• Disconnect power before servicing; remove or support the affected bin/drawer/door
• Note the old stopper's orientation and location before removal
• Transfer and reuse any original screws or clips if applicable
• Snap or fasten the new stopper in place and test for smooth movement

This holder secures the dryer-related assembly in place to reduce movement and wear, helping maintain proper alignment and quieter operation. It's a simple replacement that restores part stability in the appliance. What it does:

• Secures a dryer assembly or component to the appliance frame to prevent shifting
• Helps reduce vibration and rubbing noises caused by a loose part
• Maintains correct alignment so related parts operate smoothly
• Used when the existing holder is cracked, broken, or missing

• Disconnect power before replacing any dryer components to avoid shock or injury
• Access location and removal steps vary by model; follow the appliance's service manual or exploded view
• Keep fasteners and adjacent parts organized for reassembly; replace any damaged clips or screws

This condenser assembly is the factory-style replacement condenser wiring and support used in compatible LG refrigerators to restore proper condenser connections and securement. It helps maintain reliable cooling system electrical routing and component support. What it does:

• Provides the correct wire routing and connections for the refrigerator condenser area
• Secures condenser components in place to prevent vibration and wear
• Restores proper electrical paths for condenser-related circuits to help the compressor/fan operate as intended
• Helps address symptoms like intermittent cooling, unusual vibration, or loose wiring in the condenser compartment

• One condenser assembly as shown

• Disconnect power and follow manufacturer safety procedures before starting work
• Inspect surrounding components (fan, compressor mounts, tubing) while replacing this assembly

This fan assembly is the rotating blower that moves air through the appliance to support drying, venting, and internal cooling. Replacing a worn fan restores proper airflow and reduces noise or overheating risks. What it does

• Spins the blower wheel to circulate air for drying, venting, or cooling functions.
• Restores airflow when the appliance has weak or no air movement.
• Reduces abnormal rattling, grinding, or humming caused by a damaged motor or wheel.
• Helps prevent overheating by maintaining adequate internal ventilation.

• One fan assembly.

• Disconnect power before starting any repair.
• Access may require removing outer panels or interior trim; keep fasteners organized.
• Handle wiring connectors and harnesses carefully; match connector positions during reassembly.
• Test operation after installation and reassemble panels securely before returning the appliance to service.

The Fan Guide Assembly is an OEM component specifically designed for LG refrigerators equipped with rear evaporator fans. This assembly guides proper airflow within the refrigerator compartment.

Symptoms of a bad fan guide assembly include:

• Development of warm or cool spots inside fridge surfaces  
• Excessive frost or moisture buildup at specific locations
• Reduced temperature fluctuation stability 
• Abnormally loud fan operation sounds

Causes of failure can be damage allowing fan blade strikes, cracks reducing structural integrity over time, or accumulation of dust clogging air passages.  

Replace yours today with this genuine OEM LG assembly to maintain optimized cooling throughout storage areas. Smooth, balanced airflow preserves food freshness evenly. This replacement part is compatible with Frigidaire, GE, and Samsung models for factory fit and function. Proper air distribution helps maintain energy efficiency.

A replacement grille assembly that covers and protects the appliance fan while directing airflow for proper cooling and quieter operation. Restores the fan housing appearance and helps keep debris away from moving parts. What it does

• Protects the fan and motor from accidental contact and foreign objects
• Directs airflow for efficient cooling of the appliance components
• Helps reduce fan noise and vibration caused by loose or missing grille
• Keeps dust and large debris out of the fan area to prevent clogging

• Always disconnect power to the appliance before beginning any service
• Remove any access panels or kickplate to reach the fan area; keep fasteners for reinstallation
• Align clips or mounting tabs and secure all screws firmly but avoid overtightening

This DC motor drives the refrigerator's circulation fan, moving air across the coils and through the compartments for steady, efficient cooling. Replacing a weak, noisy, or seized motor restores airflow and temperature stability. What it does:

• Converts DC power into rotation to spin the attached fan and promote airflow
• Supports efficient heat exchange for even compartment temperatures
• Common symptoms: fan not running or intermittent, loud humming/squealing/grinding, warm spots or frost buildup, longer run times
• Contributes to reduced ice production or error codes in some models

• 1 DC motor

• Disconnect power and wear cut-resistant gloves; internal panels may have sharp edges
• Access the motor behind the interior panel or rear service panel; note connector orientation and wire routing
• Transfer the fan blade, grommets, and any mounting hardware from the old motor if needed
• Seat the blade fully and verify it spins freely before reassembly and restoring power

This motor bracket secures the washer motor to the chassis, restoring proper alignment and reducing vibration and noise caused by a loose or damaged mount. Fits the OEM motor location to keep drive components stable. What it does:

• Provides a stable mounting point for the motor to prevent movement and misalignment
• Helps reduce excessive vibration and rattling during spin and agitate cycles
• Prevents motor-to-chassis contact that can cause grinding or unusual noises
• Maintains correct motor position for proper belt/drive engagement

• Disconnect power and water before starting any repair
• Support the motor or drum when removing/installing the bracket to avoid strain on wiring or drive components
• Keep existing hardware if reusable; replace stripped or damaged screws/bolts with OEM-specified fasteners
• If noise or vibration persists after installation, inspect motor bearings, suspensions, and mounts for related wear

The Rear Evaporator Motor Grommet is an OEM part for LG refrigerators. It's designed to secure and cushion the evaporator motor, ensuring it remains in place and operates quietly. This grommet plays a crucial role in minimizing vibrations and noise from the motor, which can otherwise lead to a disruptive refrigerator operation.

Causes of a bad Rear Evaporator Motor Grommet can result from deterioration due to cooling and thawing cycles in the refrigerator. Physical damage during cleaning or servicing may cause a loose motor fit.  

Symptoms of a malfunctioning Rear Evaporator Motor Grommet include:

• Unusual noises or vibrations from the back of the refrigerator.
• The evaporator motor shifting out of place, which can affect cooling efficiency.
• Increased wear on the evaporator motor due to lack of proper cushioning and support.

This OEM LG part is also compatible with some Kenmore models.

The Front Evaporator Motor Grommet is an OEM part for LG refrigerators. This grommet cushions and secures the evaporator motor, reducing vibrations and noise during operation to ensure efficient cooling.

Causes of a bad grommet can include prolonged use leading to material fatigue, exposure to extreme temperatures, or physical damage from accidental impacts. A damaged grommet can result in increased noise and potential misalignment of the evaporator motor.

Symptoms of a bad evaporator motor grommet include:

• Increased noise from the refrigerator
• Vibrations or rattling sounds
• Poor cooling performance
• The evaporator motor becoming loose

This OEM LG part is also compatible with Sears/Kenmore.

The POWER CORD ASSEMBLY is an OEM component specifically designed for LG refrigerators. As the connection between the fridge and its power source, it is vital for safe day-to-day operation. A properly functioning power cord allows for consistent cooling and food preservation.

Causes of a bad power cord assembly can include fraying of insulation from the repeated coil/uncoil. Bends that crack internal wires pose another risk, reducing conductivity over time.

Symptoms of a bad power cord assembly include: 

• Intermittent or unreliable fridge performance  
• Loose connectivity at the wall outlet or fridge outlet
• Overheating, sparking, or safety tripping of breakers
• Inability to power fridge components like the compressor

Replace yours today with this genuine OEM cord. Proper power delivery ensures long-lasting, dependable cooling. Compatible with Sears/Kenmore as well for straightforward installation.

The Main PCB Assembly is an OEM part for LG refrigerators. As the central control hub, it incorporates the modules that regulate temperatures, lighting functions, and connected features.

Causes of failure involve water damage compromising circuitry from spills during shelving organization or condenser line clogs reducing air flow over many seasons of use.

Symptoms of a faulty main board include:

• Inability to lower temperatures adequately for preservation
• Frozen display requiring resets or unresponsive buttons
• Lights remaining lit or failing to turn off automatically
• Disruption of ice/water dispensing or internal fans

This LG part is also compatible with some Kenmore models.

This replacement sensor cover protects the washer lid sensor assembly and helps keep the sensor aligned for proper operation. It restores the sensor housing so lid-detect functions work reliably. What it does:

• Shields and secures the lid sensor assembly from moisture, lint, and physical damage.
• Helps maintain correct sensor alignment so the washer can detect lid position.
• Commonly replaced when the original cover is cracked, broken, or missing.
• Resolves symptoms like lid-not-detected errors or intermittent lid-related cycle interruptions.

• Disconnect the appliance power before beginning any repair.
• Handle the cover and sensor gently to avoid damaging the sensor or wiring.
• Follow the appliance service manual for correct removal and reassembly procedures.

This LED assembly restores the TV's backlight by replacing a failed LED strip, improving screen brightness and uniformity for visible picture. Designed to match the original part's fit and function. What it does:

• Replaces the TV's failed LED backlight strip to restore screen illumination
• Can resolve symptoms such as dim or dark screen, uneven brightness, or vertical/horizontal dark bands
• Helps stop flickering or intermittent backlight outages when caused by the LED strip
• Works with the TV's existing power board and connectors

• Disconnect power and unplug the TV before starting any repair
• Handle LEDs and the circuit board carefully; avoid touching LED surfaces and flexing the strip
• Use anti-static precautions and keep small screws and brackets organized during reassembly

This LED assembly is the backlight strip used to illuminate an LCD panel, restoring even screen brightness and color when individual LEDs fail or the backlight dims. It replaces a damaged or faulty LED strip to improve picture visibility. What it does:

• Provides uniform backlighting behind the LCD panel for consistent brightness across the screen
• Replaces burned-out or flickering LEDs that can cause dark spots, vertical bands, or uneven lighting
• Stops intermittent or flashing backlight-related display issues caused by failed LED elements
• Works with the TV's existing power module and driver board to restore normal backlight operation

• Disconnect power and unplug the TV before beginning any repair
• Handle the LED assembly and circuit board by the edges; avoid touching LEDs or solder joints
• Use proper tools and keep small screws/parts organized; follow TV disassembly guidance for your model

This temperature sensor monitors refrigerator temperatures and sends signals to the control board so it can regulate cooling and airflow. Replacing a failed sensor restores accurate readings and consistent temperatures in the fresh food and freezer sections.

• Measures internal compartment temperature for the control system
• Helps the board regulate compressor and evaporator fan operation to maintain setpoints
• Supports stable cooling and proper system cycling
• Failure may present as sections too warm or too cold, temperature swings, or frequent cycling

• Disconnect power to the refrigerator before servicing
• Access point varies by model; commonly behind an interior cover or clipped near the evaporator
• Note wire routing and any clips/insulation and transfer them to the new sensor
• Restore power and allow up to 24 hours for temperatures to stabilize

The Freezer Temperature Sensor is an OEM part for LG refrigerators. It plays a critical role in precisely monitoring freezer compartment temperatures to maintain a consistent cold environment for food storage. 

Causes of a bad temperature sensor can include wear from years of use, moisture damage impairing sensor function, or physical impact affecting circuit integrity.

Symptoms of a bad temperature sensor include:

• Inability to regulate freezer temperatures properly  
• Wide temperature fluctuations outside of set range
• Repeated ice maker or cooling failures
• Error codes indicating temperature control issues

This OEM LG replacement sensor is also compatible with some Kenmore models.