Parts for Frigidaire FFEC3625UB: Main Top / Surface Units Parts

This oven bake element heats the oven cavity so food cooks and bakes properly. Replacing a worn or broken element restores consistent heat for even baking and broiling. What it does:

• Converts electrical power into heat to warm the oven interior during bake and broil cycles
• Replaces a damaged or open element that can cause the oven to not reach temperature or cook unevenly
• Works with the oven's control system to provide steady, distributed heating
• Common symptom: oven won't heat, heats very slowly, or produces uneven cooking results

• Disconnect power at the breaker before starting any repair
• Allow the oven to fully cool and wear gloves to protect against sharp edges
• Remove the oven bottom or access panel as required, disconnect element wiring, and secure the replacement element in the original mounting
• Reconnect power and perform a short test bake to ensure proper operation

This main top is the replacement upper surface for a freestanding range that supports burners and provides a finished cooktop. It restores a flat, stable surface and helps keep heat and spills contained. What it does:

• Replaces a damaged, dented, or warped cooktop surface to restore safe burner support
• Provides a secure mounting area for burners and grates so cookware sits level
• Helps contain spills and directs crumbs away from internal components
• Restores the appliance's finished appearance for easier cleaning

• Disconnect power and gas before servicing the range
• Remove oven grates, burners, and any trim per factory instructions to access mounting screws
• Handle carefully to avoid scratching the finished surface; use proper fasteners and torque per OEM guidance

This replacement part is a maintop for electric stoves. The maintop, also known as the cooktop, is the top glass piece of the range where pots and pans are set for cooking. Glass maintops need to be replaced if they are broken or damaged. While it might seem difficult to uninstall the glass top of a stove, replacing the maintop is a very simple process. To begin replacing the maintop, make sure the range is unplugged, and the circuit breaker is off. After unplugging the stove, get under the main glass top and identify the brackets holding it down. Once identified, remove the brackets and then push up on the glass top. Once pushed up out of the stove, there will be a metal chassis attached to the glass top. Remove the screws from the chassis to remove the old glass top. Finally, place the new glass piece on top of the chassis and reconnect the screws to secure the new glass top. This is a genuine OEM part compatible with Frigidaire, Electrolux, Gibson, Kelvinator, and Westinghouse brand stoves.

This mounting bracket secures and supports internal appliance components to keep assemblies aligned and stable. It restores proper fit and reduces vibration for smoother, quieter operation. What it does:

• Provides a secure mounting point for internal panels or assemblies
• Keeps components aligned to prevent rubbing, rattling, or wear
• Reduces vibration and movement during normal operation
• Helps maintain proper door/panel fit and function when used where specified

• Disconnect power (unplug appliance or shut off breaker) before starting any repair
• Basic hand tools are typically required; access may require removing exterior panels
• Handle edges carefully; wear gloves and eye protection to avoid injury
• Follow model-specific instructions for correct placement and fastener torque

These are replacement countertop mounting screws that secure the appliance to the countertop or cabinet, restoring a stable, flush fit and preventing movement or gaps. Sold as a 2-pack for quick, direct replacement. What it does

• Secures the appliance countertop or trim to the cabinet or counter to keep the unit from shifting.
• Helps eliminate rocking, gaps, or uneven alignment caused by missing or loose mounting screws.
• Restores proper fit and finish where original mounting hardware has been lost or damaged.
• Works with factory mounting points and standard driver heads for straightforward replacement.

• Two countertop mounting screws.

• Use the correct-size driver to avoid stripping the screw head.
• Tighten until snug; avoid over-tightening which can strip threads or damage the cabinet/countertop.
• Keep original brackets and hardware; replace only the missing or damaged screws as needed.

Size: 6-20 x 0.312 inch.